+
+ +
+

Control features

+

Accel-ppp support next features for control daemon and sessions:

+
+
    +

  • accel-cmd

    • +

  • telnet

    • +

  • snmp

    • +

  • RADIUS COA

    • +
+
+

Common available commands for accel-cmd and telnet. Also possible show this help message with one of commands accel-cmd help and telnet 127.0.0.1  2000 then run help.

+
show stat - shows various statistics information
+terminate if <interface> [soft|hard]- terminate session by interface name
+        [match] username <username> [soft|hard]- terminate session by username
+        ip <address> [soft|hard]- terminate session by ip address
+        csid <id> [soft|hard]- terminate session by calling station id
+        sid <id> [soft|hard]- terminate session by session id
+        all [soft|hard]- terminate all sessions
+reload - reload config file
+restart [hard] - restart daemon
+                hard - restart immediatly
+                default action - terminate all connections then restart
+shutdown [soft|hard|cancel]- shutdown daemon
+                default action - send termination signals to all clients and wait everybody disconnects
+                soft - wait until all clients disconnects, don't accept new connections
+                hard - shutdown now, don't wait anything
+                cancel - cancel 'shutdown soft' and return to normal operation
+exit - exit cli
+show sessions [columns] [order <column>] [match <column> <regexp>] - shows sessions
+        columns:
+                netns - network namespace name
+                ifname - interface name
+                username - user name
+                ip - IP address
+                ip6 - IPv6 address
+                ip6-dp - IPv6 delegated prefix
+                type - VPN type
+                state - state of session
+                uptime - uptime (human readable)
+                uptime-raw - uptime (in seconds)
+                calling-sid - calling station id
+                called-sid - called station id
+                sid - session id
+                comp - compression/encryption method
+                rx-bytes - received bytes (human readable)
+                tx-bytes - transmitted bytes (human readable)
+                rx-bytes-raw - received bytes
+                tx-bytes-raw - transmitted bytes
+                rx-pkts - received packets
+                tx-pkts - transmitted packets
+                ipoe-type - IPoE session type
+                rate-limit - rate limit down-stream/up-stream (Kbit)
+pppoe mac-filter reload - reload mac-filter file
+pppoe mac-filter add <address> - add address to mac-filter list
+pppoe mac-filter del <address> - delete address from mac-filter list
+pppoe mac-filter show - show current mac-filter list
+pppoe interface add <name> - start pppoe server on specified interface
+pppoe interface del <name> - stop pppoe server on specified interface and drop his connections
+pppoe interface show - show interfaces on which pppoe server started
+pppoe set verbose <n> - set verbosity of pppoe logging
+pppoe set PADO-delay <delay[,delay1:count1[,delay2:count2[,...]]]> - set PADO delays (ms)
+pppoe set Service-Name <name> - set Service-Name to respond
+pppoe set Service-Name * - respond with client's Service-Name
+pppoe set AC-Name <name> - set AC-Name tag value
+pppoe show verbose - show current verbose value
+pppoe show PADO-delay - show current PADO delay value
+pppoe show Service-Name - show current Service-Name value
+pppoe show AC-Name - show current AC-Name tag value
+shaper change <interface> <value> [temp] - change shaper on specified interface, if temp is set then previous settings may be restored later by 'shaper restore'
+shaper change all <value> [temp] - change shaper on all interfaces, if temp is set also new interfaces will have specified shaper value
+shaper restore <interface> - restores shaper settings on specified interface made by 'shaper change' command with 'temp' flag
+shaper restore all - restores shaper settings on all interfaces made by 'shaper change' command with 'temp' flag
+
+
+
+

accel-cmd

+

This application is very powerful and often used if you have cli connection. Be default accel-ppp listen TCP port 2000 for input/output with accel-cmd. However telnet has same functions, but accel-cmd is more comfortable, allow send command without enter in to another environment. Detail about cli you may read at [cli] .Let’s revise accel-cmd possible commands.

+
+
    +

  • accel-cmd show stat - one of more important command, allow display accel-ppp daemon statistics and information about connections types and something counters such as RADIUS auth, acct summary and lost queries. Detail below:

    • +
+
+
+
+

telnet

+
+
+

radius CoA

+

Example, terminate session by username: echo User-Name=username | radclient -x 127.0.0.1:3799 disconnect testing123.

+
+
+

snmp

+
+
+ + +
+