| Age | Commit message (Collapse) | Author |
|---|
|
Jinja template contains some workarounds like {% if port is string %}, this
depends of the resolution of https://phabricator.vyos.net/T2636
|
|
|
|
T2486: DNS, vyos-hostsd fixes
|
|
|
|
|
|
|
|
For more examples on the new get_config_dict() approach migrate this
implementation as it is not yet in production use. Also this serves as proof of
concept code for further migrations.
|
|
|
|
|
|
radvd[31898]: AdvValidLifeTime must be greater than AdvPreferredLifetime in
radvd.conf, line 19
This happens with the following configuration:
vyos@vyos# show service router-advert
interface eth0.20 {
name-server 2001:4860:4860::8888
prefix ::/64 {
valid-lifetime 7200
}
}
A validator is added to solve this issue and radvd will run again.
|
|
|
|
|
|
When multiple RADIUS servers have been configured, they have been all rendered
onto a single line in the config. This lead to errors in syslog and not all
servers beeing reachable.
|
|
The "to" qualifier did not get rendered when using source ports in masquerade
targets. This case was totally missed out when porting.
|
|
|
|
|
|
We specify NFT source/destination ports within a { } group, but if the port
range in question is negated, we need to move the != fraction out of { } and
infront of that group, else NFT loading will fail big time.
|
|
This reverts commit 927c054d9236c2c34ca43c1cbfff10fcfd7f5077.
|
|
After commit 1c7d7cb ("wwan: T2529: migrate device from ttyUSB to
usbXbY.YpZ.Z") the up/down scripts did not properly parse the passed tty
for setting up default routes.
|
|
|
|
The file will be generated by vyos-hostsd to add NTAs for zones (domains)
from /etc/hosts and forward-zones.
|
|
Move templates out of the daemon and add new templates.
|
|
As part of T1595 listen-on was removed and migrated to listen-address,
but some references to it stayed in the variable names and validator
error message.
|
|
|
|
|
|
* 'serial-console' of github.com:c-po/vyos-1x:
console: T2569: run VGA console powersave on tty1
console: T2569: replicate console settings to grub.cfg
Debian: fix warning about undefined substitution variables
console: T2569: only start serial console if device exists
console: T2529: migrate from ttyUSB device to new device in /dev/serial/by-bus
console: T2570: remove support for Hayes Modems
netconsole: T2561: use migrator to delete config nodes
console: T2569: initial implementation with XML and Python
|
|
|
|
|
|
During testing it was discovered that there is a well known problem (we had for
ethernet interfaces) also in the serial port world. They will be enumerated and
mapped to /dev/ttyUSBxxx differently from boot to boot. This is especially
painful on my development APU4 board which also has a Sierra Wireless MC7710
LTE module installed.
The serial port will toggle between ttyUSB2 and ttyUSB5 depending on the
amount of serial port extenders attached (FT4232H).
The shipped udev rule (/usr/lib/udev/rules.d/60-serial.rules) partly solves
this by enumerating the devices into /dev/serial/by-id folder with their name
and serial number - it's a very good idea but I've found that not all of the
FT4232H dongles have a serial number programmed - this leads to the situation
that when you plug in two cables with both having serial number 0 - only one
device symlink will appear - the previous one is always overwritten by the
latter one.
Derive /usr/lib/udev/rules.d/60-serial.rules and create a /dev/serial/by-bus
directory and group devices by attached USB root port.
|
|
|
|
... all information are present in journald.
|
|
During testing it was discovered that there is a well known problem (we had for
ethernet interfaces) also in the serial port world. They will be enumerated and
mapped to /dev/ttyUSBxxx differently from boot to boot. This is especially
painful on my development APU4 board which also has a Sierra Wireless MC7710
LTE module installed.
The serial port will toggle between ttyUSB2 and ttyUSB5 depending on the
amount of serial port extenders attached (FT4232H).
The shipped udev rule (/usr/lib/udev/rules.d/60-serial.rules) partly solves
this by enumerating the devices into /dev/serial/by-id folder with their name
and serial number - it's a very good idea but I've found that not all of the
FT4232H dongles have a serial number programmed - this leads to the situation
that when you plug in two cables with both having serial number 0 - only one
device symlink will appear - the previous one is always overwritten by the
latter one.
Derive /usr/lib/udev/rules.d/60-serial.rules and create a /dev/serial/by-bus
directory and group devices by attached USB root port.
vyos@vyos:~$ find /dev/serial/by-bus/ -name usb* -exec basename {} \; | sort
usb0b1.3p1.0
usb0b1.3p1.2
usb0b1.3p1.3
usb0b2.4p1.0
usb0b2.4p1.1
usb0b2.4p1.2
usb0b2.4p1.3
So we have USB root 0 with bus 1.3 and port 1.0. The enumeration is constant
accross reboots.
|
|
|
|
|
|
|
|
|
|
Commit 8dcf042a7f5 ("pppoe: T2219: move adding of default route to ip-(up|down)
script") wrongly tried to open a file called autoconfigure which infact
should be autoconf
|
|
|
|
Some ISPs (e.g. Comcast) only delegate a /64 by default. You have to explicitly
"ask" for a bigger (e.g. /60) prefix. This commit adds a CLI node to request
a specific prefix length in the range 32 - 64.
dhcpv6-options {
prefix-delegation {
length 60
}
}
|
|
Rename the CLI nodes for prefix delegation from "dhcpv6-options delegate
<interface>" to "dhcpv6-options prefix-delegation interface <interface>".
The change is required to add the possibility to request for specific prefix
sized via the CLI. That option was not possible with the old configuration
tree.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
MACsec always talks about MKA (MACsec Key Agreement protocol) thus the node
should reflect that.
|
|
|
|
|
|
|
