Age | Commit message (Collapse) | Author |
|
parsing, and migration to valueless node for log and state matchers
|
|
firewal, nat and nat66.
(cherry picked from commit 51abbc0f1b2ccf4785cf7f29f1fe6f4af6007ee6)
|
|
|
|
If ethernet interface is a bond memeber:
1. Allow for changing only specific parameters which are specified
in EthernetIf.get_bond_member_allowed_options function.
2. Added inheritable parameters from bond interface to ethernet
interface which are scpecified
in BondIf.get_inherit_bond_options.
Users can change inheritable options under ethernet interface
but in commit it will be copied from bond interface.
3. All other parameters are denied for changing.
Added migration script. It deletes all denied parameters under
ethernet interface if it is a bond member.
(cherry picked from commit aa0282ceb379df1ab3cc93e4bd019134d37f0d89)
|
|
Currently VyOS VXLAN implementation uses the Linux assigned port 8472 that
predates the IANA assignment. As Most other vendors use the IANA assigned port,
follow this guideline and use the new default port 4789.
Existing configuration not defining an explicit port number will be migrated
to the old default port number of 8472, keeping existing configurations work!
(cherry picked from commit 6db8d3ded19f652b99231be0d705d76b598ac72a)
# Conflicts:
# interface-definitions/include/version/interfaces-version.xml.i
|
|
(cherry picked from commit 4c4c2b1f8a58398798f20c252bde80461320d330)
|
|
Migrate policy local-route <destination|source> to node address
replace 'policy local-route{v6} rule <tag> destination|source <x.x.x.x>'
=> 'policy local-route{v6} rule <tag> destination|source address <x.x.x.x>'
(cherry picked from commit 9f7a5f79200782f7849cab72f55a39dedf45f214)
|
|
|
|
Disabeled adding the peer with the same public key as the router has.
Added smoketest
|
|
T5154: NTP: allow maximum of one ipv4 and one ipv6 address on paramet…
|
|
<listen-address>. Also allow only one single value <interface>.
|
|
Migrate:
high-availability virtual-server 203.0.113.1
to: high-availability virtual-server <name> address 203.0.113.1
|
|
... this is a step towards a new and better implementation that will utilize
VPP.
|
|
Create migration and bump package version from 0 -> 1 for dynamic dns
|
|
syslog: T2778: T2769: refactoring and VRF support
|
|
|
|
|
|
|
|
|
|
Tunnel interface multicast settings can be "enabled or disabled". As we prefer
valueless nodes, and the linux kernel default is "disabled" we should add a
set interfaces tunnel tunXX enable-multicast
command
|
|
Not supported with swanctl
|
|
sstp-client
|
|
T4916: Rewrite IPsec peer authentication and psk migration
|
|
Rewrite strongswan IPsec authentication to reflect structure
from swanctl.conf
The most important change is that more than one local/remote ID in the
same auth entry should be allowed
replace: 'ipsec site-to-site peer <tag> authentication pre-shared-secret xxx'
=> 'ipsec authentication psk <tag> secret xxx'
set vpn ipsec authentication psk <tag> id '192.0.2.1'
set vpn ipsec authentication psk <tag> id '192.0.2.2'
set vpn ipsec authentication psk <tag> secret 'xxx'
set vpn ipsec site-to-site peer <tag> authentication local-id '192.0.2.1'
set vpn ipsec site-to-site peer <tag> authentication mode 'pre-shared-secret'
set vpn ipsec site-to-site peer <tag> authentication remote-id '192.0.2.2'
Add template filter for Jinja2 'generate_uuid4'
|
|
T4857: SNMP: Implement FRR SNMP Recomendations
|
|
warning message
|
|
* Move CLI from "system ntp" -> "service ntp"
* Drop NTP server option preempt as not supported by chrony
|
|
|
|
move from vfs to overlay driver
The following pre iage upgrade script must be executed to have containers after
the reboot:
for pod in $(cli-shell-api listActiveNodes container name); do
systemctl stop vyos-container-${pod//\'}.service
done
sed -i 's/vfs/overlay/g' /etc/containers/storage.conf /usr/share/vyos/templates/container/storage.conf.j2
rm -rf /usr/lib/live/mount/persistence/container/storage/libpod
for pod in $(cli-shell-api listActiveNodes container name); do
image=$(cli-shell-api returnActiveValue container name ${pod//\'} image)
podman image pull $image
systemctl start vyos-container-${pod//\'}.service
done
for dir in vfs vfs-containers vfs-images vfs-layers; do
rm -rf /usr/lib/live/mount/persistence/container/storage/$dir
done
|
|
T4780: Firewall: add firewall groups in firewall. Extend matching cri…
|
|
so this new group can be used in inbound and outbound matcher
|
|
<name> interface <ifname>`
* Include refactor to policy route to allow for deletion of mangle table instead of complex cleanup
* T4605: Rename mangle table to vyos_mangle
|
|
|
|
This is to refactor ISIS segment routing to match up with OSPF segment routing.
|
|
Changed CLI syntax in route-map set community,
set large-community, set extcommunity
Allows to add multiple communities, large-communities
and extcommunities in clear view.
Added new well-known communities.
Added non-transitive feature in extcommunities.
Fixed community's validators.
|
|
ids: T4557: Migrate threshold and add new threshold types
|
|
Migrate "service ids ddos-protection threshold xxx" to
"service ids ddos-protection general threshold xxx"
Add new threshold types:
set service ids ddos-protection threshold tcp xxx
set service ids ddos-protection threshold udp xxx
set service ids ddos-protection threshold icmp xxx
|
|
The initial Accel-PPP PPPoE implementation used:
set service pppoe-server interface <name> vlan-id <id>
set service pppoe-server interface <name> vlan-range <start-stop>
This is actually a duplicated CLI node.
|
|
ipsec: T4118: Change vpn ipsec syntax for IKE ESP and peer
|
|
Migration and Change boolean nodes "enable/disable" to
disable-xxxx, enable-xxxx and just xxx for VPN IPsec
configurations
- IKE changes:
- replace 'ipsec ike-group <tag> mobike disable'
=> 'ipsec ike-group <tag> disable-mobike'
- replace 'ipsec ike-group <tag> ikev2-reauth yes|no'
=> 'ipsec ike-group <tag> ikev2-reauth'
- ESP changes:
- replace 'ipsec esp-group <tag> compression enable'
=> 'ipsec esp-group <tag> compression'
- PEER changes:
- replace: 'peer <tag> id xxx'
=> 'peer <tag> local-id xxx'
- replace: 'peer <tag> force-encapsulation enable'
=> 'peer <tag> force-udp-encapsulation'
- add option: 'peer <tag> remote-address x.x.x.x'
Add 'peer <name> remote-address <name>' via migration script
|
|
firewall node
* Refactor firewall and zone-policy rule creation and cleanup
* Migrate interface firewall values to `firewall interfaces <name> <direction> name/ipv6-name <name>`
* Remove `firewall-interface.py` conf script
|
|
bgp: T4257: Changing BGP "local-as" to "system-as"
This change is to change the global BGP name for the node "local-as" to "system-as"
This is needed so that there's less ambiguity with the local-as feature per neighbor.
bgp: T4257: Changing BGP "local-as" to "system-as"
bgp: T4257: Changing BGP "local-as" to "system-as"
This change is to change the global BGP name for the node "local-as" to "system-as"
This is needed so that there's less ambiguity with the local-as feature per neighbor.
|
|
As we have specific configuration for each plugin:
set service monitoring telegraf xxx
- azure-data-explorer
- prometheus-client
- splunk
We should to move configuration that related to influxdb under
influxdb node
Replace:
set service monitoring telegraf
- authentication xxx
- bucket xxx
- port xxx
- url
To:
set service monitoring telegraf influxdb xxx
|
|
After discussion with @zsdc this was decided the better long term fix
* Removes hourly logrotate cron in favour of systemd timer override
|
|
|
|
|
|
|
|
present for DHCP
VyOS 1.4 still leverages PPPd internals on the CLI.
pppd supports three options for a default route, none, auto, force.
* none: No default route is installed on interface up
* auto: Default route is only installed if there is yet no default route
* force: overwrite any default route
There are several drawbacks in this design for VyOS and the users. If auto is
specified, this only counted for static default routes - but what about dynamic
ones? Same for force, only a static default route got replaced but dynamic ones
did not got taken into account.
The CLI is changed and we now re-use already existing nodes from the DHCP
interface configuration:
* no-default-route:
On link up no default route is installed, same as the previous
default-route none
* default-route-distance:
We can now specify the distance of this route for the routing table on the
system. This defaults to 210 as we have for DHCP interfaces. All this will be
migrated using a CLI migration script.
|
|
|
|
|