summaryrefslogtreecommitdiff
path: root/interface-definitions
AgeCommit message (Collapse)Author
2023-12-21T2898: add ndp-proxy serviceChristian Breunig
VyOS CLI command set service ndp-proxy interface eth0 prefix 2001:db8::/64 mode 'static' Will generate the following NDP proxy configuration $ cat /run/ndppd/ndppd.conf # autogenerated by service_ndp-proxy.py # This tells 'ndppd' how often to reload the route file /proc/net/ipv6_route route-ttl 30000 # This sets up a listener, that will listen for any Neighbor Solicitation # messages, and respond to them according to a set of rules proxy eth0 { # Turn on or off the router flag for Neighbor Advertisements router no # Control how long to wait for a Neighbor Advertisment message before invalidating the entry (milliseconds) timeout 500 # Control how long a valid or invalid entry remains in the cache (milliseconds) ttl 30000 # This is a rule that the target address is to match against. If no netmask # is provided, /128 is assumed. You may have several rule sections, and the # addresses may or may not overlap. rule 2001:db8::/64 { static } } (cherry picked from commit 4d721a58020971d00ab854c37b68e88359999f9c)
2023-12-21srv6: T591: enable SR enabled packet processing on defined interfacesChristian Breunig
The Linux Kernel needs to be told if IPv6 SR enabled packets whether should be processed or not. This is done using /proc/sys/net/conf/<iface>/seg6_* variables: seg6_enabled - BOOL Accept or drop SR-enabled IPv6 packets on this interface. Relevant packets are those with SRH present and DA = local. 0 - disabled (default) not 0 - enabled Or the VyOS CLI command: * set protocols segment-routing interface eth0 srv6 (cherry picked from commit 774cc97eda61eb0b91df820797fb3c705d0073d5)
2023-12-21dhcp: T5846: Ensure DUID regex range is boundIndrajit Raychaudhuri
The DUID regex was missing a lower bound, which could cause it not to match when it should. We have to specify the lower bound explicitly as 0 to keep the regex behavior similar to that in Python (in Python, omitting the lower bound is equivalent to specifying 0). (cherry picked from commit 551f06218755076cde588c848c01ce5ca1bf5e6b)
2023-12-21dhcp: T5846: Fix include pathIndrajit Raychaudhuri
(cherry picked from commit 5768bc2d56cc8aabd8d276a2afc30608c1bc9838)
2023-12-21dhcp: T5846: Refactor and simplify DUID definitionIndrajit Raychaudhuri
Refactor DUID XML definition in conf-mode to be reusable. Additionally, remove explicit call to a separate validator `ipv6-duid` and inline the regex into the XML definition. (cherry picked from commit 51e7832fc5c88f9956b26157a80947bad4495a4e)
2023-12-20T5798: load-balancing revese-proxy add multiple SSL certificatesViacheslav Hletenko
Add ability to configure multiple SSL certificates for frontend/service set load-balancing reverse-proxy service web mode http set load-balancing reverse-proxy service web port 443 set load-balancing reverse-proxy service web ssl certificate cert1 set load-balancing reverse-proxy service web ssl certificate cert2 (cherry picked from commit fe99c45e05fd5794905145ddca80e6078145c2e8)
2023-12-18T4163: Add BGP Monitoring Protocol BMP featureViacheslav Hletenko
Add BMP feature. BMP (BGP Monitoring Protocol, RFC 7854) is used to send monitoring data from BGP routers to network management entities https://docs.frrouting.org/en/latest/bmp.html Example: set system frr bmp commit run restart bgp set protocols bgp system-as '65001' set protocols bgp neighbor 192.0.2.11 address-family ipv4-unicast set protocols bgp neighbor 192.0.2.11 remote-as '65001' set protocols bgp bmp mirror-buffer-limit '256000000' set protocols bgp bmp target foo address '127.0.0.1' set protocols bgp bmp target foo port '5000' set protocols bgp bmp target foo min-retry '1000' set protocols bgp bmp target foo max-retry '2000' set protocols bgp bmp target foo mirror set protocols bgp bmp target foo monitor ipv4-unicast post-policy set protocols bgp bmp target foo monitor ipv4-unicast pre-policy set protocols bgp bmp target foo monitor ipv6-unicast post-policy set protocols bgp bmp target foo monitor ipv6-unicast pre-policy (cherry picked from commit 5523fccf4f7d05444c36c568128e94cd7b08c34f)
2023-12-16ocserv: T5796: add CLI knob "http-security-headers"fett0
OCserv manual recommended HTTP headers tobe included in the configuration. (cherry picked from commit ad65d37ddf92ec8416c84707d7d41e63346b550c) (cherry picked from commit 24f449cc099703df95646c719e9d3f308ed1a3f0)
2023-12-15T5775: firewall: re-add state-policy to firewall. These commands are now ↵Nicolas Fort
included in <set firewall global-options state-policy> node.
2023-12-15firewall: T4502: add offload to firewall table actionsBjarke Istrup Pedersen
2023-12-15frr: T4020: add option to define number of open file descriptorsChristian Breunig
This allows the operator to control the number of open file descriptors each daemon is allowed to start with. The current assumed value on most operating systems is 1024. If the operator plans to run bgp with several thousands of peers then this is where we would modify FRR to allow this to happen. set system frr descriptors <n> (cherry picked from commit 892c28ccf634173d4c4952c248cb03974c560793)
2023-12-13srv6: T591: initial implementation to support locator definitionChristian Breunig
VyOS CLI set protocols segment-routing srv6 locator bar prefix '2001:b::/64' set protocols segment-routing srv6 locator foo behavior-usid set protocols segment-routing srv6 locator foo prefix '2001:a::/64' Will generate in FRR segment-routing srv6 locators locator bar prefix 2001:b::/64 block-len 40 node-len 24 func-bits 16 exit ! locator foo prefix 2001:a::/64 block-len 40 node-len 24 func-bits 16 behavior usid exit ! exit ! exit ! exit (cherry picked from commit ca301cdd4746187f96ff84e411fda6a84e33f237)
2023-12-13bgp: T591: add SRv6 support from FRRChristian Breunig
set protocols bgp sid vpn per-vrf export '99' set protocols bgp srv6 locator 'foo' set protocols bgp system-as '100' Will generate in FRR config router bgp 100 no bgp ebgp-requires-policy no bgp default ipv4-unicast no bgp network import-check ! segment-routing srv6 locator foo exit sid vpn per-vrf export 99 exit (cherry picked from commit af46fe54e56cf85d13b62ee771bec3d80f225ac5)
2023-12-09git: T5803: Adjust git configuration for baseline defaultsIndrajit Raychaudhuri
Apply baseline defaults for `.gitattributes` and `.vscode/settings.json` for improved developer experience. The `.gitattrbutes` settings are based on: Git documentation (https://git-scm.com/docs/gitattributes#_effects) GitHub documentation (https://docs.github.com/en/get-started/getting-started-with-git/configuring-git-to-handle-line-endings) Community templates (https://github.com/gitattributes/gitattributes) Since editor-agnostic line-ending specific settings are applied to `.gitattributes`, they can be removed from `.vscode/settings.json`. The global VSCode defaults have also been removed to avoid duplication. (cherry picked from commit c30002208d392177cb1ffc1a5c714f7ad6d573b6)
2023-12-08Merge pull request #2581 from vyos/mergify/bp/sagitta/pr-2578Viacheslav Hletenko
T160: add NAT64 (backport #2578)
2023-12-07T160: Rebase and fixes for NAT64Viacheslav Hletenko
- Update the base (rebase) - Move include/nat64-protocol.xml.i => include/nat64/protocol.xml.i - Delete unwanted `write_json`, use `write_file` instead - Remove unnecessary deleting of default values for tagNodes T2665 - Add smoketest Example: ``` set interfaces ethernet eth0 address '192.168.122.14/24' set interfaces ethernet eth0 address '192.168.122.10/24' set interfaces ethernet eth2 address '2001:db8::1/64' set nat64 source rule 100 source prefix '64:ff9b::/96' set nat64 source rule 100 translation pool 10 address '192.168.122.10' set nat64 source rule 100 translation pool 10 port '1-65535' ``` (cherry picked from commit 336bb5a071b59264679be4f4f9bedbdecdbe2834)
2023-12-07nat64: T160: Implement Jool-based NAT64 translatorJoe Groocock
Signed-off-by: Joe Groocock <me@frebib.net> (cherry picked from commit 7d49f7079f1129c2fadc7f38ceb230804d89e177) # Conflicts: # debian/control
2023-12-05ddclient: T5791: Migration script for dynamic dns config path changeIndrajit Raychaudhuri
2023-12-05ddclient: T5791: Remove XML includes that aren't used anymoreIndrajit Raychaudhuri
As followup to interface definition change, remove XML snippets that aren't used anymore. They were there because they were 'include'-ed multiple times in the interface definition `dynamic-dns.xml.in`. Since that's not the case anymore, they can be removed.
2023-12-05ddclient: T5791: Update dynamic dns configuration pathIndrajit Raychaudhuri
Modify the configuration path to be consistent with the usual dialects of VyoS configuration (wireguard, dns, firewall, etc.) This would also shorten the configuration path and have a unified treatment for RFC2136-based updates and other 'web-service' based updates. While at it, add support for per-service web-options. This would allow for probing different external URLs on a per-service basis.
2023-12-01http-api: T5782: use single config-mode script for https and http-apiJohn Estabrook
2023-12-01Merge pull request #2557 from vyos/mergify/bp/sagitta/pr-2467Christian Breunig
T5727: Use native URL validator instead of regex-based validator (backport #2467)
2023-12-01policy: T4704: Allowed to set metric (MED) to (+/-)rttaapostoliuk
Allowed to set metric (MED) to (+/-)rtt in the route-map. (cherry picked from commit 5d98e806ef4edb4439620eff60215aaf30b5a592)
2023-12-01T5727: Use native URL validator instead of regex-based validatorIndrajit Raychaudhuri
Replace regex-based URL validator with native validator from vyos-utils. Also, move `include/url.xml.i` to `include/url-http-https.xml.i` to reflect the fact that it is used only for HTTP(S) URLs. (cherry picked from commit 64322b19d6968195a6dc7c82e7e22126072377f5)
2023-11-30ddclient: T5708: Migrate `timeout` to `interval`Indrajit Raychaudhuri
Time interval in seconds to wait between DNS updates would be a bit more intuitive as `interval` than `timeout`.
2023-11-30ddclient: T5574: Support per-service cache management for servicesIndrajit Raychaudhuri
Add support for per-service cache management for ddclient providers via `wait-time` and `expiry-time` options. This allows for finer-grained control over how often a service is updated and how long the hostname will be cached before being marked expired in ddclient's cache. More specifically, `wait-time` controls how often ddclient will attempt to check for a change in the hostname's IP address, and `expiry-time` controls how often ddclient to a forced update of the hostname's IP address. These options intentionally don't have any default values because they are provider-specific. They get treated similar to the other provider- specific options in that they are only used if defined.
2023-11-30ddclient: T5612: Refactor zone configurationIndrajit Raychaudhuri
Refactor zone configuration to use shared XML snippet for all cases.
2023-11-30ddclient: T5612: Relax hostname validation for apex and wildcard entryIndrajit Raychaudhuri
Some porvides (like 'namecheap') allow to use '@' or '*' as hostname prefix for apex and wildcard records. This commit relaxes the hostname validation to allow these prefixes.
2023-11-30ddclient: T5612: Enable TTL support for web-service based protocolsIndrajit Raychaudhuri
Enable TTL support for web-service based protocols in addition to RFC2136 based (nsupdate) protocol. Since TTL is not supported by all protocols, and thus cannot have a configuration default, the existing XML snippet `include/dns/time-to-live.xml.i` does not have common `<defaultValue>300</defaultValue>` anymore and is instead added explicitly whenever necessary.
2023-11-30ddclient: T5612: Fix VRF support for ddclient serviceIndrajit Raychaudhuri
Fix VRF support interface definition and configuration mode for ddclient to actually capture the VRF name and pass it to the template.
2023-11-30Merge pull request #2526 from vyos/mergify/bp/sagitta/pr-2503Daniil Baturin
vxlan: T5759: change default MTU from 1450 -> 1500 bytes (backport #2503)
2023-11-22pppoe: T5630: make MRU default to MTU if unspecifiedChristian Breunig
This fixes the implementation in e062a8c11 ("pppoe: T5630: allow to specify MRU in addition to already configurable MTU") and restores the bahavior that MRU defaults to MTU if MRU is not explicitly set. This was the behavior in VyOS 1.3.3 and below before we added ability to define the MRU value. (cherry picked from commit ffd7339e2ea3eafdd97ac0763ca4a3913fe71bf3)
2023-11-22vxlan: T5759: change default MTU from 1450 -> 1500 bytesChristian Breunig
Found an odd behavior on Linux and the VyOS CLI implementation. If adding VXLAN interfaces using iproute2 the MTU differs depending on the creation syntax: ip -4 link add vxlan100 type vxlan dstport 4789 external df unset tos inherit \ ttl 16 nolearning vnifilter local 172.16.33.201 ip -4 link add vxlan200 type vxlan id 200 dstport 4789 local 172.16.33.201 dev eth0 ip -6 link add vxlan300 type vxlan id 300 dstport 4789 local 2001:db8:1::1 dev eth0 132: vxlan300: <BROADCAST,MULTICAST> mtu 1430 qdisc noop state DOWN group default qlen 1000 link/ether 4e:fb:e3:f5:d9:59 brd ff:ff:ff:ff:ff:ff 133: vxlan200: <BROADCAST,MULTICAST> mtu 1450 qdisc noop state DOWN group default qlen 1000 link/ether 0e:4e:f4:76:59:3f brd ff:ff:ff:ff:ff:ff 134: vxlan100: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN group default qlen 1000 link/ether ba:b6:b7:0c:b1:37 brd ff:ff:ff:ff:ff:ff VyOS always sets a default MTU of 1450 bytes which is correct for IPv4 p2p links or multicast, but invalid for IPv6 p2p. Also this will break EVPN deployments as ethernet bridges with MTU < 1500 bytes are less fun. Increase default MTU to 1500 bytes. Migrate old configurations to use 1450 bytes if not specified otherwise on the CLI. (cherry picked from commit 4a163b016333e58fee9d6ec6b53a09e0160b3213)
2023-11-22vxlan: T5753: add support for VNI filteringChristian Breunig
In a service provider network a service provider typically supports multiple bridge domains with overlapping vlans. One bridge domain per customer. Vlans in each bridge domain are mapped to globally unique VXLAN VNI ranges assigned to each customer. Without the ability of VNI filtering, we can not provide VXLAN tunnels with multiple tenants all requiring e.g. VLAN 10. To Test: set interfaces vxlan vxlan987 parameters external set interfaces vxlan vxlan987 source-interface eth0 set interfaces vxlan vxlan987 parameters vni-filter set interfaces vxlan vxlan987 vlan-to-vni 50 vni 10050 set interfaces vxlan vxlan987 vlan-to-vni 51 vni 10051 set interfaces vxlan vxlan987 vlan-to-vni 52 vni 10052 set interfaces vxlan vxlan987 vlan-to-vni 53 vni 10053 set interfaces vxlan vxlan987 vlan-to-vni 54 vni 10054 set interfaces vxlan vxlan987 vlan-to-vni 60 vni 10060 set interfaces vxlan vxlan987 vlan-to-vni 69 vni 10069 set interfaces bridge br0 member interface vxlan987 Add new op-mode command: show bridge vni Interface VNI ----------- ----------- vxlan987 10050-10054 vxlan987 10060 vxlan987 10069 (cherry picked from commit 35f6033d21053fa420e837f157cd9377a4ccd26a)
2023-11-22http: T5762: rename "virtual-host listen-port" -> "virtual-host port"Christian Breunig
This complements commit f5e43b136 ("http: T5762: api: make API socket backend communication the one and only default") so we have a consistent port CLI node across VyOS components. (cherry picked from commit 0e885f1bf01424130b6876e769cc42612b19351b)
2023-11-22Merge pull request #2517 from nicolas-fort/T5419-FT-SagittaDaniil Baturin
T5419: firewall: backport firewall flowtable to Sagitta.
2023-11-22Merge pull request #2510 from vyos/mergify/bp/sagitta/pr-2506Daniil Baturin
dhcp-client: T5760: add CLI option to pass user-class parameter (backport #2506)
2023-11-21T5419: firewall: backport firewall flowtable to Sagitta.Nicolas Fort
2023-11-21Merge pull request #2512 from zdc/T5577-sagittaChristian Breunig
PAM: T5577: Backported PAM settings from circinus
2023-11-20http: T5762: api: make API socket backend communication the one and only defaultChristian Breunig
Why: Smoketests fail as they can not establish IPv6 connection to uvicorn backend server. https://github.com/vyos/vyos-1x/pull/2481 added a bunch of new smoketests. While debugging those failing, it was uncovered, that uvicorn only listens on IPv4 connections vyos@vyos# netstat -tulnp | grep 8080 (Not all processes could be identified, non-owned process info will not be shown, you would have to be root to see it all.) tcp 0 0 127.0.0.1:8080 0.0.0.0:* LISTEN - As the CLI already has an option to move the API communication from an IP to a UNIX domain socket, the best idea is to make this the default way of communication, as we never directly talk to the API server but rather use the NGINX reverse proxy. (cherry picked from commit f5e43b1361fb59a9c260739bdb28729d5119507c)
2023-11-20TACACS: T5577: Added `mandatory` and `optional` modes for TACACS+zsdc
In CLI we can choose authentication logic: - `mandatory` - if TACACS+ answered with `REJECT`, authentication must be stopped and access denied immediately. - `optional` (default) - if TACACS+ answers with `REJECT`, authentication continues using the next module. In `mandatory` mode authentication will be stopped only if TACACS+ clearly answered that access should be denied (no user in TACACS+ database, wrong password, etc.). If TACACS+ is not available or other errors happen, it will be skipped and authentication will continue with the next module, like in `optional` mode.
2023-11-20RADIUS: T5577: Added `mandatory` and `optional` modes for RADIUSzsdc
In CLI we can choose authentication logic: - `mandatory` - if RADIUS answered with `Access-Reject`, authentication must be stopped and access denied immediately. - `optional` (default) - if RADIUS answers with `Access-Reject`, authentication continues using the next module. In `mandatory` mode authentication will be stopped only if RADIUS clearly answered that access should be denied (no user in RADIUS database, wrong password, etc.). If RADIUS is not available or other errors happen, it will be skipped and authentication will continue with the next module, like in `optional` mode.
2023-11-20dhcp-client: T5760: add CLI option to pass user-class parameterChristian Breunig
Example: set interfaces ethernet eth0 dhcp-options user-class VyOS or set interfaces ethernet eth0 dhcp-options user-class 56:79:4f:53 (cherry picked from commit 260645d0c6ff078cc89601f3a586195902f9c18e)
2023-11-20dhcp-client: T5760: add constraints for dhclient string optionsChristian Breunig
The string data type specifies either an NVT ASCII string enclosed in double quotes, or a series of octets specified in hexadecimal, separated by colons. For example: set interfaces ethernet eth0 dhcp-options client-id CLIENT-FOO or set interfaces ethernet eth0 dhcp-options client-id 43:4c:49:45:54:2d:46:4f:4f As of now there was no input validation performed. (cherry picked from commit bed1cd01904ef89b5d31bd47de0f230214900f16)
2023-11-19config-mgmt: T4957: remove TFTP user/pass from completion helperChristian Breunig
(cherry picked from commit e92667504e0c503b7c0d125d89d8795d6b6d5876)
2023-11-19config-mgmt: T4957: T2405: add proper valueHelp strings for remote URLChristian Breunig
vyos@vyos# set system config-management commit-archive location Possible completions: uri Uniform Resource Identifier Unfortunately URI is a bit "less" specific - add proper help strings: vyos@vyos# set system config-management commit-archive location Possible completions: http://<user>:<passwd>@<host>/<path> https://<user>:<passwd>@<host>/<path> ftp://<user>:<passwd>@<host>/<path> sftp://<user>:<passwd>@<host>/<path> scp://<user>:<passwd>@<host>/<path> tftp://<user>:<passwd>@<host>/<path> git+https://<user>:<passwd>@<host>/<path> (cherry picked from commit dcb277ba0aed4a02f48572d10d3ba242942b8639)
2023-11-19T2405: add Git support to commit-archiveYun Zheng Hu
(cherry picked from commit a89243cfbfc90854a8cddd53c0ffc987f75abcee)
2023-11-19Merge pull request #2498 from nicolas-fort/T4072-sagittaChristian Breunig
T4072: firewall: backport bridge firewall to sagitta
2023-11-16T4072: firewall: backport bridge firewall to sagittaNicolas Fort
2023-11-16xml: T5738: re-use "disable" building blockChristian Breunig
(cherry picked from commit 019723aaa4217403f1fcbcd636f573ea403f909c)