Age | Commit message (Collapse) | Author |
|
Ability to terminate interactive sessions (TTY/PTS) after a period
of inactivity.
set system login timeout '300'
|
|
ids: T4557: Migrate threshold and add new threshold types
|
|
Migrate "service ids ddos-protection threshold xxx" to
"service ids ddos-protection general threshold xxx"
Add new threshold types:
set service ids ddos-protection threshold tcp xxx
set service ids ddos-protection threshold udp xxx
set service ids ddos-protection threshold icmp xxx
|
|
This commit raises the minimum TCP MSS clamping range to the MSS value
corresponding to the minimum packet size that must be accepted for IPv4.
|
|
This extends commit 28573ffe4f ("xml: T4698: drop validator name="range" and
replace it with numeric"). The first version allowed both a range and discrete
numbers to be validated by the numeric validator.
This had a flaw as both 22 and 22-30 were valid at the same time. The generic
"port-number.xml.i" building block only allows a discrete number. Now if a user
set port 22-30 for e.g. SSH the daemon did no longer start. This is why range
validation must be explicitly enabled.
|
|
update-check: T3476: Allow update-check for VyOS images
|
|
|
|
T4699: Firewall: Add return action
|
|
|
|
In addition to the rewrite to make use of get_config_dict() the CLI is
slightly adjusted as specified in T4703.
* Rename vlan-id and vlan-range to simply vlan
* Rename network-mode to simply mode
* Re-use existing common Jinja2 template for Accel-PPP which are shared
with PPPoE and SSTP server.
* Retrieve default values via defaultValue XML node
|
|
|
|
name
|
|
|
|
T4699: Firewall: Add jump action in firewall ruleset
|
|
The initial Accel-PPP PPPoE implementation used:
set service pppoe-server interface <name> vlan-id <id>
set service pppoe-server interface <name> vlan-range <start-stop>
This is actually a duplicated CLI node.
|
|
ipsec: T4118: Change vpn ipsec syntax for IKE ESP and peer
|
|
|
|
Migration and Change boolean nodes "enable/disable" to
disable-xxxx, enable-xxxx and just xxx for VPN IPsec
configurations
- IKE changes:
- replace 'ipsec ike-group <tag> mobike disable'
=> 'ipsec ike-group <tag> disable-mobike'
- replace 'ipsec ike-group <tag> ikev2-reauth yes|no'
=> 'ipsec ike-group <tag> ikev2-reauth'
- ESP changes:
- replace 'ipsec esp-group <tag> compression enable'
=> 'ipsec esp-group <tag> compression'
- PEER changes:
- replace: 'peer <tag> id xxx'
=> 'peer <tag> local-id xxx'
- replace: 'peer <tag> force-encapsulation enable'
=> 'peer <tag> force-udp-encapsulation'
- add option: 'peer <tag> remote-address x.x.x.x'
Add 'peer <name> remote-address <name>' via migration script
|
|
|
|
This will set the listen-host ocserv configuration option.
|
|
After T4669 added support for range validation to the OCaml validator there is
no need to keep the slow Python validator in place.
Raplace all occurances of <validator name="range" argument="--min=1 --max=65535"/>
with <validator name="numeric" argument="--range 1-65535"/>.
|
|
T3896(adjacent): Fix ocserv local user requirement, add groupconfig
|
|
Add new VyOS CLI command:
set protocols bgp parameters bestpath peer-type multipath-relax
This command specifies that BGP decision process should consider paths from all
peers for multipath computation. If this option is enabled, paths learned from
any of eBGP, iBGP, or confederation neighbors will be multipath if they are
otherwise considered equal cost. [1]
[1]: http://docs.frrouting.org/en/stable-8.3/bgp.html#clicmd-bgp-bestpath-peer-type-multipath-relax
|
|
* 'T4689' of https://github.com/jack9603301/vyos-1x:
rfs: T4689: Support RFS(Receive Flow Steering)
|
|
|
|
Kernel 5.15.y and newer only support an upper boundary of 255.
vyos@vyos:~$ sudo sysctl -w net.netfilter.nf_conntrack_tcp_max_retrans=255
net.netfilter.nf_conntrack_tcp_max_retrans = 255
vyos@vyos:~$ sudo sysctl -w net.netfilter.nf_conntrack_tcp_max_retrans=256
sysctl: setting key "net.netfilter.nf_conntrack_tcp_max_retrans": Invalid argument
|
|
Add Spain (es) and Japan (jp106) keymaps
set system option keyboard-layout es|jp106
|
|
firewall: zone-policy: T2199: T4605: Refactor firewall, migrate zone-policy
|
|
|
|
firewall node
* Refactor firewall and zone-policy rule creation and cleanup
* Migrate interface firewall values to `firewall interfaces <name> <direction> name/ipv6-name <name>`
* Remove `firewall-interface.py` conf script
|
|
This reverts commit 53355271a2864d844daca89a064c21e514e10adb.
|
|
|
|
The local-policy and local-policy6 nodes were missing their priority
property causing an ordering issue between the creation of dynamic
interfaces (like VLAN/Bonding) and referencing said interface in PBR
rules.
Add a priority value to order local-policy(6) to be after all interface
definitions.
|
|
Ability to autocheck available new images
Parse remote URL JSON image-version.json file and compare version
VyOS with a local current version, if find diff sent wall
message that the new image is available
Also, add op-mode command to check images "show system image"
With option "auto-check" check will be once per 12 hours
set system update-check auto-check
set system update-check url 'http://example.com/image-version.json'
If new version is available shows it per login (MOTD)
|
|
firewall and in policy route
|
|
Matching criteria added: ttl/hoplimit and packet-length
|
|
|
|
|
|
|
|
* 'T4651' of https://github.com/nicolas-fort/vyos-1x:
Firewall: T4651: Change proposed cli from ip-length to packet-length
Firewall: T4651: Add options to match packet size on firewall rules.
|
|
|
|
|
|
This extends the implementation of commit 0cc7e0a49094 ("firewall: T4655: Fix
default action 'drop' for the firewall") in a way that we can now also use the
XML <defaultValue> node under "firewall name" and "firewall ipv6-name". This
is a much cleaner approach which also adds the default value automatically to
the CLIs completion helper ("?").
|
|
|
|
|
|
Fix wrong descriptions for the RPKI server
It was mentioned about the NTP server
|
|
|
|
nat66: T4631: Add port and protocol to nat66 conf
|
|
|
|
|