| Age | Commit message (Collapse) | Author |
|---|
|
It is easier to backport the entire vyos.ifconfig library from 1.4 instead of
backporting single pieces which are required to add new feature to the tunnel
interface section.
In addition that both libraries are now back in sync it will become much easier
to backport any other new feature introduced in VyOS 1.4!
|
|
Option specifying the rate in which we'll ask our link partner to transmit
LACPDU packets in 802.3ad mode.
set interfaces bonding bond0 lacp-rate <slow|fast>
slow: Request partner to transmit LACPDUs every 30 seconds (default)
fast: Request partner to transmit LACPDUs every 1 second
(cherry picked from commit 8e392a3dbc16f7b80a979f7b4e9c11408d700e6f)
|
|
When a VIF/VLAN interface is placed in admin down state but the lower
interface, serving the vlan, is moved from admin down -> admin up, all its
vlan interfaces will be placed in admin up state, too.
This is bad as a VLAN interface will become admin up even if its specified as
admin down after a reboot.
To reproduce:
set interfaces ethernet eth1 vif 20 disable
set interfaces ethernet eth1 disable
commit
delete interfaces ethernet eth1 disable
commit
Now check the interface state and it returns UP,LOWER_UP
7: eth1.20@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 00:50:56:b3:09:07 brd ff:ff:ff:ff:ff:ff
inet6 fe80::250:56ff:feb3:907/64 scope link
valid_lft forever preferred_lft forever
(cherry picked from commit 49bc3f1e3ff8416908fc986bb60b444a75a1722d)
|
|
Renamed using snippet below:
----------------------------
for file in $(find . -name "*.py")
do
sed -i "s/vyos_dict_search/dict_search/" $file
done
|
|
Instead of using an Adapter pattern to make interfaces VLAN-aware, create a
derived class named VLANIf to represent a VLAN. This change was necessary to
eliminate mixed code in Interfaces class which was VLAN - free, but recently
gained some VLAN specific code for set_admin_state().
In addition this "autoresolves" the issue in T2894 as a bond vlan interface
will no longer change the lower interface.
|
|
Removing a member from a bond/LACP will turn the physical interface always in
admin-down state. This is invalid, the interface should be placed into the state
configured on the VyOS CLI.
Smoketest on bond interfaces is extended to check this behavior.
|
|
Specifies the minimum number of links that must be active before asserting
carrier. It is similar to the Cisco EtherChannel min-links feature. This allows
setting the minimum number of member ports that must be up (link-up state)
before marking the bond device as up (carrier on). This is useful for situations
where higher level services such as clustering want to ensure a minimum number
of low bandwidth links are active before switchover.
This option only affects 802.3ad mode.
The default value is 0. This will cause carrier to be asserted (for 802.3ad
mode) whenever there is an active aggregator, regardless of the number of
available links in that aggregator. Note that, because an aggregator cannot be
active without at least one available link, setting this option to 0 or to 1
has the exact same effect.
|
|
|
|
Commit 29dd5079 ("ifconfig: T2653: remove duplicated code for address flush")
used the class method for address flushing, but it was cvalled in the wrong way.
|
|
|
|
The current VyOS CLI parser code written in Python contains a ton of duplicates
which I can also hold myself accountable for - or maybe mainly me - depends on
the angle of judge.
|
|
|
|
The Interface get_state/set_state were not clear about
if they edited the admin or operational state.
functions are now using admin_state and oper_state
for clarity.
|
|
|
|
|
|
__init__ should be added to a derived class only if it does work in the ctor.
|
|
|
|
|
