| Age | Commit message (Collapse) | Author |
|---|
|
When a VIF/VLAN interface is placed in admin down state but the lower
interface, serving the vlan, is moved from admin down -> admin up, all its
vlan interfaces will be placed in admin up state, too.
This is bad as a VLAN interface will become admin up even if its specified as
admin down after a reboot.
To reproduce:
set interfaces ethernet eth1 vif 20 disable
set interfaces ethernet eth1 disable
commit
delete interfaces ethernet eth1 disable
commit
Now check the interface state and it returns UP,LOWER_UP
7: eth1.20@eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP group default qlen 1000
link/ether 00:50:56:b3:09:07 brd ff:ff:ff:ff:ff:ff
inet6 fe80::250:56ff:feb3:907/64 scope link
valid_lft forever preferred_lft forever
(cherry picked from commit 49bc3f1e3ff8416908fc986bb60b444a75a1722d)
|
|
FileNotFoundError: [Errno 2] failed to run command: ip link set dev wg01 master br0
|
|
While migration to get_config_dict() was introduced in commit 789775af9f5 the
logic for adding an IPv4 or IPv6 peer address was using the wrong dictionary
to determine if it's an IPv4 or IPv6 address.
We now use the proper peer dict over the wrong config dict.
|
|
link-local addresses can still be disabled using:
set interfaces wireguard wg0 ipv6 address no-default-link-local
|
|
|
|
Generate an IPv6 Link Local address for wireguard interfaces.
|
|
We had two places were the is_ip, is_ipv4 and is_ipv6 helpers had been defined.
All places now have been converged into vyos.template as they are used both
in the Jinja2 templates and also in our scripts.
|
|
Instead of using an Adapter pattern to make interfaces VLAN-aware, create a
derived class named VLANIf to represent a VLAN. This change was necessary to
eliminate mixed code in Interfaces class which was VLAN - free, but recently
gained some VLAN specific code for set_admin_state().
In addition this "autoresolves" the issue in T2894 as a bond vlan interface
will no longer change the lower interface.
|
|
The current VyOS CLI parser code written in Python contains a ton of duplicates
which I can also hold myself accountable for - or maybe mainly me - depends on
the angle of judge.
|
|
Commit 289f513 ("wireguard: T2632: support PSK on multiple peers") introduced
a regression when multiple allowed-ips have been configured. They were not
properly quoted when passing them down to the wg binary.
|
|
It was not possible to configure two WG peers with both utilized a pre-shared
key. This has been corrected.
WG psk can only be read from a file when starting the interface. The code for
creating this temporary file has been moved into the ifconfig.WireGuardIf()
class.
Tested with:
============
set interfaces wireguard wg0 address '192.0.2.0/31'
set interfaces wireguard wg0 peer one allowed-ips '0.0.0.0/0'
set interfaces wireguard wg0 peer one preshared-key 'e+SIIUcrnrSDHhbTtpjwKhSlSdUALA5ZvoCjfQXcvmA='
set interfaces wireguard wg0 peer one pubkey '/qQGAQ2HfLSZBSCpdgps04r9wRlK7bSFraCH9+MScmw='
set interfaces wireguard wg0 peer two allowed-ips '0.0.0.0/0'
set interfaces wireguard wg0 peer two pubkey '/qQGAQ2HfLSZBSCpdgfooor9wRlK7bSFraCH9+MScmw='
|
|
|
|
|
|
All operational command are moved within an Operational
class and an inherited on for wireguard.
|
|
|
|
Some left over wireguard code was left in the interface.py
file. The code was moved into the wireguard.py file and
the now empty interface.py file removed as no longer holdin
any code.
|
|
when ifconfig.py was broken down in multiple files an import
was missed. This fixes this import
|
|
|
|
|
|
|
|
__init__ should be added to a derived class only if it does work in the ctor.
|
|
- That should probably move to it's own op command library
as it is the onlt function print out specific information
|
|
|
