| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This reverts commit 9541355433e202fade4692851bffa33ba9d48f44.
|
|
Migrate from
ethernet eth1 {
offload-options {
generic-receive on
generic-segmentation on
scatter-gather on
tcp-segmentation on
udp-fragmentation on
}
}
to
ethernet eth1 {
offload {
ufo
tso
sg
gso
gro
}
}
|
|
|
|
|
|
|
|
|
|
Using 'xdp' will automatically decide if the driver supports 'xdpdrv' or only
'xdpgeneric'. A user later sees which driver is actually in use by calling
'ip a' or 'show interfaces ethernet'.
|
|
The CLI command 'set interfaces ethernet <interface> offload-options xdp" enables
the XDP generic mode on the given interface.
vyos@vyos:~$ show interfaces ethernet eth1
eth1: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 xdpgeneric/id:151 qdisc mq state DOWN group default qlen 1000
link/ether 00:50:56:bf:ef:aa brd ff:ff:ff:ff:ff:ff
inet6 fe80::250:56ff:febf:efaa/64 scope link tentative
valid_lft forever preferred_lft forever
Description: fooa
XDP code is thankfully copied from [1], thank you for this nice tutorial.
NOTE: this is an experimental feature which might break your
forwarding/filtering.
[1]: https://medium.com/swlh/building-a-xdp-express-data-path-based-peering-router-20db4995da66
|
|
|
|
Since the dependency problem has not been solved before,
if the monitoring interface does not exist when the
mirror rule is created, the execution will be abnormal
|
|
setting and streamline the code
|
|
|
|
of `bridge` should not be overwritten
|
|
`vlan_filter` to avoid redundant paths
|
|
|
|
|
|
mirror: T3089: support two-way traffic mirroring
|
|
|
|
This is the second attempt after commit d247736f ("vyos.ifconfig: T1579: do not
remove IPv6 link-local address on reconfiguration"). We only clean out link-local
IPv6 addresses left over after an interface MAC change.
|
|
reconfiguration"
This reverts commit d247736f67cc056062b75a4215a031bebcfee2ee.
We need to clean link-local IPv6 addresses on link reconfiguration to also drop
no longer existing link-local addresse son MAC address change.
|
|
|
|
vyatta-cfg-quagga
|
|
|
|
|
|
class
|
|
FileNotFoundError: [Errno 2] failed to run command: ip link set dev wg01 master br0
|
|
|
|
|
|
|
|
|
|
While migration to get_config_dict() was introduced in commit 789775af9f5 the
logic for adding an IPv4 or IPv6 peer address was using the wrong dictionary
to determine if it's an IPv4 or IPv6 address.
We now use the proper peer dict over the wrong config dict.
|
|
link-local addresses can still be disabled using:
set interfaces wireguard wg0 ipv6 address no-default-link-local
|
|
|
|
|
|
|
|
|
|
The MAC address is changed after we have set an IP address on the interface or
started dhclient. This will cause some users to receive the wrong IP address
on device startup.
Change to order of how parameters are set in the system. The interface MAC
address is now configured first.
|
|
In the implementation of T3042, it will cause two problems:
1. Even if VLAN awareness is not enabled, the VLAN settings of the
vlan filter will be modified. When the bridge member has a WLAN interface,
the error is exposed, so repair it here. You should not modify the
related settings when the VLAN awareness mode is not enabled
2. Even if VLAN awareness is not enabled, the VLAN settings of the
vlan filter will be modified. When the bridge member has a WLAN interface,
due to special settings, the bridge mode cannot be entered and the settings
cannot be completed directly. Therefore, the WLAN interface should be rejected
Enter the bridge with VLAN awareness
|
|
This reverts commit 806f35b5856c3f8dae634718a6a9e82cc90bb63a.
Unfortunately this did not work our in the attempt to bridge a station to a
bridge "brX" interface. Also adjusting the wireless interface during operation
cause several exceptions and the feature is removed again as it was never in any
production system.
|
|
In #601, I provided a basic patch. Under this patch, I rely on vif to
detect the vlan id range that the bridge should flow through,
which may lead to greater redundancy in the configuration,
so I am considering detecting effective vlan filters In setting the range
of vlan id that is required to flow through the bridge,
I use set() to complete the deduplication of this vlan id
and set it to the bridge uniformly (at the same time,
I slightly modified the smoke test script)
|
|
We had two places were the is_ip, is_ipv4 and is_ipv6 helpers had been defined.
All places now have been converged into vyos.template as they are used both
in the Jinja2 templates and also in our scripts.
|
|
1. Due to the previous focus on the implementation of VLAN filter, it was not considered to include MTU settings, which will lead to MTU setting errors in some cases
2. In order to make VLAN aware of the work of the bridge, it is necessary to specify the allowed VLAN ID range for the bridge itself, and forget to join it before
|
|
|
|
|
|
|
|
|
|
Renamed using snippet below:
----------------------------
for file in $(find . -name "*.py")
do
sed -i "s/vyos_dict_search/dict_search/" $file
done
|
|
|
|
almost every interface can be part of a bridge thus the code for changing STP
cost is best part of the Interface() base class itself.
Commit b5ef10cf ("ifconfig: T2985: support on demand bridge creation")
implemented this change but the STP file was not removed on the test devices
causing tests to pass.
|
