Age | Commit message (Collapse) | Author |
|
|
|
|
|
default-doct
* 'T2588' of https://github.com/thomas-mangin/vyos-1x:
xml: T2588: code to extract defaults values from xml
|
|
|
|
T2486: DNS, vyos-hostsd fixes
|
|
|
|
Merge two dictionaries. Only keys which are not present in destination will
be copied from source, anything else will be kept untouched. Function will
return a new dict which has the merged key/value pairs.
Before:
{'device': {'usb0b2.4p1.0': {'speed': '9600'},
'usb0b2.4p1.1': {'data-bits': '8',
'parity': 'none',
'speed': '115200',
'stop-bits': '2'}}}
After:
{'device': {'usb0b2.4p1.0': {'data-bits': '8',
'parity': 'none',
'speed': '9600',
'stop-bits': '1'},
'usb0b2.4p1.1': {'data-bits': '8',
'parity': 'none',
'speed': '115200',
'stop-bits': '2'}}}
|
|
|
|
|
|
|
|
|
|
|
|
Instead of using "show version" as catch-all command for information rather
add "show system cpu" op-mode command which is analogous to "show system memory"
which deals with RAM.
|
|
|
|
Commit 728b1feaf744 ("dhcpv6-pd: T2551: fix prefix length not set in config")
reworked the way the configuration path is accesses on the individual
interfaces, but it was missed out to apply it correctly when reading in
sla-len and sla-id values.
|
|
Retrieving the CLI nodes from current config was missed out and only
implemented for PPPoE.
|
|
A typo caused vif-s interfaces to not commit.
|
|
|
|
|
|
airbag :T2088: make airbag explicit
|
|
airbag must now be explicitly installed.
the patch also allow to fully disables the installation of the logging
code at setup (and not just installing and doing nothing)
|
|
After commit d5b58517f883 ("dhcpv6-pd: pppoe: T2506: restructure CLI") the
CLI syntax has been adjusted for a better definition of DHCPv6-PD prefix length
option. Verifying a properly rendered template indeed did not happen which
cause the function to vanish for non PPPoE interfaces.
|
|
|
|
Some ISPs (e.g. Comcast) only delegate a /64 by default. You have to explicitly
"ask" for a bigger (e.g. /60) prefix. This commit adds a CLI node to request
a specific prefix length in the range 32 - 64.
dhcpv6-options {
prefix-delegation {
length 60
}
}
|
|
Rename the CLI nodes for prefix delegation from "dhcpv6-options delegate
<interface>" to "dhcpv6-options prefix-delegation interface <interface>".
The change is required to add the possibility to request for specific prefix
sized via the CLI. That option was not possible with the old configuration
tree.
|
|
|
|
|
|
By default MACsec only authenticates traffic but has support for optional
encryption. Encryption can now be enabled using:
set interfaces macsec <interface> encrypt
|
|
|
|
|
|
|
|
|
|
util: T2467: automatically add sudo to known commands
|
|
|
|
|
|
|
|
Add support for prefix delegation when receiving the prefix via ethernet,
bridge, bond, wireless.
|
|
|
|
Dictionary is used to remove the amount of duplicated code by e.g. ethernet
or bridge interface.
|
|
|
|
|
|
|
|
The following configuration will assign a /64 prefix out of a /56 delegation
to eth0. The IPv6 address assigned to eth0 will be <prefix>::ffff/64.
If you do not know the prefix size delegated to you, start with sla-len 0.
pppoe pppoe0 {
authentication {
password vyos
user vyos
}
description sadfas
dhcpv6-options {
delegate eth0 {
interface-id 65535
sla-id 0
sla-len 8
}
}
ipv6 {
address {
autoconf
}
enable
}
source-interface eth1
}
vyos@vyos:~$ show interfaces
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
eth0 2001:db8:8003:400::ffff/64 u/u
|
|
ISC does not support running the client on PPP(oE) interfaces which makes it
unusable for DHCPv6 Prefix Delegation tasks.
Internet Systems Consortium DHCP Client 4.4.1
Copyright 2004-2018 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Unsupported device type 512 for "pppoe0"
|
|
Currently accept_ra was set to 0 if 'address dhcpv6' was set on an
interface. This is wrong, as without RA, the system will get no routes
to the DHCPv6-obtained prefix.
Since the logic for accept_ra was moved to the interface scripts,
it can be removed from the dhclient code.
|
|
|
|
To make SLAAC and DHCPv6 work when forwarding=1, accept_ra must be 2
(default for accept_ra is 1).
|
|
|
|
validator: T2417: try to make the code clearer
|
|
|