| Age | Commit message (Collapse) | Author |
|---|
|
|
|
In addition to commit cf1156a60e ("ethernet: T3163: probe driver for maximum
rx/tx ring-buffer size") this extends the logic in a way as not every driver
supports setting the buffers at all so it will properly error out.
When invoking "ethtool -g" both stdout and stderr are captured and no exception
is raised if it's an unsupported driver feature. The verify() section will
inform the user about the illegal operation.
|
|
As thought in the beginning the dhcp-interface route option can not be
superseeded by the interface option. When a route is installed for a DHCP
interface, that interface is usually a broadcast interface which can not be
used for plain interface-based routes.
The old Vyatta logic was migrated to Python where the current received
next-hop address from the DHCP interface is installed as next-hop address.
|
|
|
|
|
|
This helper class could be used to interact and retrieve information from
ethtool. It is not used so far in production code.
|
|
If the subprocess is producing enough data (in this case showConfig on a
large config file), then the construction:
p = subprocess.Popen(.., stdout=subprocess.PIPE, ..)
p.wait()
will deadlock with the subprocess waiting for data to be consumed, while
the Python process waits for its termination. So consume data, then wait
for termination.
|
|
|
|
This will enable more debugging on the frr reload library, changes:
* Adds a /tmp/vyos.frr.debug hook to enable system wide vyos.frr debugging
* Log the initial imported configs
* Log the FRR config submitted to frr-reload
* redirecting frr-reload output to the debug log.
|
|
tunnel: T3030: Add erspan protocol support
|
|
In the past it was possible to configure a vif-s interface and a vif interface
both with the same VLAN ID. VyOS 1.2 reported a Kernel error:
RTNETLINK answers: File exists
Error creating VLAN device eth1.100
so this should not be possible at all in VyOS 1.3
|
|
package type automatic detection)
|
|
|
|
vyos: T3274: Handle EOF in ask_yes_no()
|
|
|
|
|
|
If dhcpv6-options is configured without requesting a DHCPv6 address or PD, the
dhcpv6pd variable is assigned an empty dict.
|
|
A hyphen in a route-map name will be converted to _, take care about this
effect during validation.
|
|
|
|
|
|
The raw key was not copied into the class member variable. Also added a smoketest
to ensure the configured parameters are always set.
|
|
Support a 1:1 or 1:n prefix translation. The following configuration will NAT
source addresses from the 10.2.0.0/16 range to an address from 192.0.2.0/29.
For this feature to work a Linux Kernel 5.8 or higher is required!
vyos@vyos# show nat
source {
rule 100 {
outbound-interface eth1
source {
address 10.2.0.0/16
}
translation {
address 192.0.2.0/29
}
}
}
This results in the nftables configuration:
chain POSTROUTING {
type nat hook postrouting priority srcnat; policy accept;
oifname "eth1" counter packets 0 bytes 0 snat ip prefix to ip saddr map
{ 10.2.0.0/16 : 192.0.2.0/29 } comment "SRC-NAT-100"
}
|
|
|
|
|
|
|
|
|
|
bridge: T3137: Let VLAN aware bridge approach the behavior of professional equipment
|
|
|
|
|
|
|
|
equipment
According to the consensus, the specific behavior of a VLAN aware bridge should conform
to the behavior of professional equipment. This commit makes a significant change to the
behavior of VLAN aware bridge, and has the following behaviors:
1. Disable `vif 1` configuration
2. When the VLAN aware bridge is enabled, the parent interface is always VLAN 1
3. When `native-vlan` is not configured, the default behavior of the device is `native-vlan 1`
4. The VLAN ids forwarded by the bridge are determined by `vif`
5. It has an `enable-vlan` node to enable VLAN awareness
6. VLAN configuration is allowed only when VLAN aware bridge is activated
|
|
After switching to iproute2 in commit 92f36735 ("ifconfig: T2653: use iproute2
commands for alias, mac and mtu set()/get()" it is necessary to return an empty
string as iproute2 returns None.
|
|
|
|
|
|
|
|
|
|
configured SLA-IDs
"data/templates/dhcp-client/ipv6.tmpl" handles the auto-assigning of SLA-IDs on
lines 39, 46, and 52.
|
|
"data/templates/dhcp-client/ipv6.tmpl" handles the auto-assigning of SLA-IDs on
lines 39, 46, and 52.
|
|
VLAN interfaces contain periods, which make them incompatible with
dict_search().
|
|
|
|
|
|
|
|
|
|
- remove redundant code paths apply_mirror() / apply_mirror_of_monitor()
- have single source available
|
|
The Linux Kernel supports enabling more cores for RPS then we actually have.
It does internal clipping/validation so there is no need for us to calculate
the specifc enable mask we can simply throw "all -1" at the Kernel.
|
|
|
|
set interfaces ethernet <interface> offload rps
|
|
|
|
|
|
is wrong
In e8957b5, we used json to parse the `tc qdisc` filter to determine whether it needs
to be deleted (reduction of exception mechanism), but now we find that the json output
by this command will output unparsed json in some cases,
so We have to go back to the processing of the exception mechanism
|
