Age | Commit message (Collapse) | Author |
|
firewall: T4622: Add TCP MSS option
|
|
A macsec interface requires a dedicated source interface, it can not be
shared with another macsec or a pseudo-ethernet interface.
set interfaces macsec macsec10 address '192.168.2.1/30'
set interfaces macsec macsec10 security cipher 'gcm-aes-256'
set interfaces macsec macsec10 security encrypt
set interfaces macsec macsec10 security mka cak '232e44b7fda6f8e2d88a07bf78a7aff4232e44b7fda6f8e2d88a07bf78a7aff4'
set interfaces macsec macsec10 security mka ckn '09924585a6f3010208cf5222ef24c821405b0e34f4b4f63b1f0ced474b9bb6e6'
set interfaces macsec macsec10 source-interface 'eth1'
commit
set interfaces pseudo-ethernet peth0 source-interface eth1
commit
Reuslts in
FileNotFoundError: [Errno 2] failed to run command: ip link add peth0 link eth1 type macvlan mode private
returned:
exit code: 2
noteworthy:
cmd 'ip link add peth0 link eth1 type macvlan mode private'
returned (out):
returned (err):
RTNETLINK answers: Device or resource busy
[[interfaces pseudo-ethernet peth0]] failed
Commit failed
|
|
|
|
The VLAN aware bridge was forwarding traffic between member ports, but traffic
destined torwards the CPU was dropped. This resulted in a gateway not reachable
or DHCP leases that could not be handed out.
Tested via:
VyOS
set interfaces bridge br0 enable-vlan
set interfaces bridge br0 member interface eth1 allowed-vlan '10'
set interfaces bridge br0 member interface eth1 allowed-vlan '20'
set interfaces bridge br0 member interface eth1 allowed-vlan '30'
set interfaces bridge br0 member interface eth1 allowed-vlan '40'
set interfaces bridge br0 member interface eth1 native-vlan '40'
set interfaces bridge br0 member interface eth2 allowed-vlan '30'
set interfaces bridge br0 member interface eth2 allowed-vlan '20'
set interfaces bridge br0 member interface eth2 allowed-vlan '10'
set interfaces bridge br0 member interface eth2 allowed-vlan '40'
set interfaces bridge br0 vif 10 address '10.0.10.1/24'
set interfaces bridge br0 vif 20 address '10.0.20.1/24'
set interfaces bridge br0 vif 30 address '10.0.30.1/24'
set interfaces bridge br0 vif 40 address '10.0.40.1/24'
Arista vEOS
vlan 10,20,30,40
interface Ethernet1
switchport trunk allowed vlan 10,20,30,40
interface Vlan10
ip address 10.0.10.2/24
interface Vlan20
ip address 10.0.20.2/24
interface Vlan30
ip address 10.0.30.2/24
interface Vlan40
ip address 10.0.40.2/24
interface Ethernet1
switchport trunk allowed vlan 10,20,30,40
switchport mode trunk
spanning-tree portfast
Cisco vIOS
interface GigabitEthernet0/0
ip address 10.0.40.3 255.255.255.0
duplex auto
speed auto
media-type rj45
!
interface GigabitEthernet0/0.10
encapsulation dot1Q 10
ip address 10.0.10.3 255.255.255.0
!
interface GigabitEthernet0/0.20
encapsulation dot1Q 20
ip address 10.0.20.3 255.255.255.0
!
interface GigabitEthernet0/0.30
encapsulation dot1Q 30
ip address 10.0.30.3 255.255.255.0
!
|
|
We check listen port before commit service if is port available and
not bounded, but when we start openconnect our own port starts be
bounded by "ocserv-main" process and next commit will be fail as
port is already bound
To fix it, extend check if port already bonded and it is not our
self process "ocserv-main"
|
|
Ability to drop|accept packets based on TCP MSS size
set firewall name <tag> rule <tag> tcp mss '501-1460'
|
|
T2719: add an exception hierarchy for op mode errors
|
|
|
|
on error
|
|
We should not print the entire dictionary - we only need the bridge interface
name:
Bug:
Cannot assign address to interface "eth1" as it is a member of bridge
"{'br0': {'allowed_vlan': ['5-50', '101'], 'native_vlan': '101'}}"!
Fixed:
Cannot assign address to interface "eth1" as it is a member of bridge
"br0"!
|
|
Ability to get MTU from DHCP-server and don't touch it per
any interface change if interface 'dhcp-options mtu' is
configured
|
|
... otherwise functionality like bridge VLANs will loose configuration
on membe rinterface update (e.g. description)
|
|
|
|
Interface() base class already takes care about VLAN creation/removal of
newly added or no longer required interfaces. No need to code this logic again.
|
|
This reverts commit fdeae251431cb747e8f60d96269b4365b7401807.
|
|
It is useful to have both a return code and output of the command
Add a new wrapper "rc_cmd" that returns both
% rc_cmd('uname')
(0, 'Linux')
% rc_cmd('ip link show dev fake')
(1, 'Device "fake" does not exist.')
|
|
|
|
|
|
T2719: prototype of an op mode command runner based on type hints and introspection
|
|
|
|
|
|
Signed-off-by: Daniil Baturin <daniil@vyos.io>
|
|
|
|
When removing a VRF from an ethernet interface and adding the interface to a
bond in the same commit led to an OSError: [Errno 16] Device or resource busy!
|
|
This extends commit 39157912 ("vyos.configdict(): T4228: is_member() must use
the "real" hardware interface") and returns the config dict of the used member
interfaces.
|
|
It makes no sense to enslave an interface to a bond or a bridge device if it is
bound to a given VRF. If VRFs should be used - the encapuslating/master
interface should be part of the VRF.
Error out if the member interface is part of a VRF.
|
|
|
|
Commit 39157912 ("vyos.configdict(): T4228: is_member() must use the "real"
hardware interface") added a bugfix on calling is_member() to retrieve the real
physical information about an interface. It did not include a code path to also
split up VLAN interfaces.
This has been fixed.
|
|
Linux Kernel supports to specify the MII link monitoring frequency in
milliseconds. This determines how often the link state of each slave is
inspected for link failures. A value of zero disables MII link monitoring.
A value of 100 is a good starting point.
The default value is 100.
set interfaces bonding bond0 mii-mon-interval <n>
|
|
When is_member() is inspecting the bridge/Bond member interfaces it must work
with the real interface (e.g. eth1) under the "ethernet" node and not work on
the "member interface eth1" CLI tree, that makes no sense at all.
|
|
|
|
The code path for changing the interval is never executed.
|
|
Directed broadcast is described in rfc1812#section-5.3.5.2 and rfc2644.
By default Linux kernel doesn't forward directed broadcast
packets unless both of `/proc/sys/net/ipv4/conf/all/bc_forwarding`
and `/proc/sys/net/ipv4/conf/$iface/bc_forwarding` are set to 1.
|
|
Since Python as of 3.9 doesn't give us an option to look up
argument's default value by its name,
this implementation requires that all boolean options
must default to false.
|
|
|
|
openvpn: T4485: Accept multiple tls ca-certificate values
|
|
Interface should receive an auto generated link-local IPv6 address as we do
with all VyOS interfaces by default.
|
|
* Also determines and maps to correct CA for migrated CRL
|
|
This PR adds an config option to enable/disable IGMP/MLD snooping.
```
set interfaces bridge brN igmp snooping
```
|
|
|
|
Error introduced by commit 85d6c8f7c ("vyos.configdict: T4391: enable
get_interface_dict() ti be used with ConfigTreeQuery()"). Reason was the
still in use relative path on calls to node_changed(), these got
replaced with absolute config paths and the new implementation if
is_node_changed().
|
|
Commit a2ab95ff68b ("pppoe: T4384: replace default-route CLI option with common
CLI nodes already present for DHCP") had an issue as the PPPoE interface options
and also DHCP interface options did not honor the no-default-route option.
This has been fixed.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* Refactor nftables clean-up code
* Adds policy route test for using firewall groups
|
|
|