| Age | Commit message (Collapse) | Author |
|---|
|
bgp: T6106: Valid commit error for route-reflector-client option defi…
|
|
This is a leftover after commit 0e050cb35 (isis: T3417: drop artificial "domain"
node identifying the IS-IS process name). Drop all references to "process"
variable.
Specifying:
set protocols isis interface eth1
set protocols isis net '49.0001.1921.6825.5255.00'
set protocols isis redistribute ipv4 bgp
Triggered an exception
Traceback (most recent call last):
File "/usr/libexec/vyos/conf_mode/protocols_isis.py", line 309, in <module>
verify(c)
File "/usr/libexec/vyos/conf_mode/protocols_isis.py", line 158, in verify
f'"protocols isis {process} redistribute {afi} {proto}"!')
^^^^^^^
NameError: name 'process' is not defined
|
|
vti: T6085: interface is always down and only enabled by IPSec daemon
|
|
bridge: T6125: support 802.1ad (ethertype 0x88a8) VLAN filtering
|
|
* Move global state-policy smoketest to it's own test, verify conntrack
|
|
Linux bridge uses EtherType 0x8100 by default. In some scenarios, an EtherType
value of 0x88A8 is required.
Reusing CLI command from VIF-S (QinQ) interfaces:
set interfaces bridge br0 protocol 802.1ad
|
|
When a VTI interface is just created, it is in ADMIN UP state by default, even
if an IPSec peer is not connected. After the peer is disconnected the interface
goes to DOWN state as expected.
This breaks routing logic - for example, static routes through VTI interfaces
will be active even if a peer is not connected.
This changes to logic so ADMIN UP/DOWN state can only be changed by the
vti-up-down helper script.
Error was introduced during the Perl -> Python migration and move to the generic
vyos.ifconfig abstraction during the 1.4 development cycle.
|
|
peer-group
handle vtysh bgp error
|
|
qos: T1871: add MTU option when configure limiter traffic-policy
|
|
T5996: selectively escape and restore single backslashes in config
|
|
|
|
add mtu to default and specified class
update smoke test
|
|
policy: T6129: add route-map option "as-path exclude all"
|
|
Remove all AS numbers from the AS_PATH of the BGP path's NLRI.
set policy route-map <name> rule <rule> set as-path exclude all
|
|
conntrack: T4022: add RTSP conntrack helper
|
|
Add support for pref64 option, as defined in RFC8781. The prefix valid lifetime
must not be smaller than the "interface interval max" definition which defaults
to 600.
set service router-advert interface eth1 nat64prefix 64:ff9b::/96
|
|
|
|
firewall: T6071: truncate rule description field to 255 characters
|
|
e.g. Linux Kernel only supports 255 and not 256 characters for the ifalias field.
|
|
vrrp: T6020: vrrp health-check script not applied correctly
|
|
|
|
|
|
ospfv3: T6087: add support to redistribute IS-IS routes
|
|
vyos.ethtool: T6083: use JSON input data #2
|
|
is a network.
|
|
|
|
|
|
settings
|
|
ospfv3: allow metric and metric-type on redistributed routes
|
|
Example:
vyos@vyos# set protocols ospfv3 redistribute bgp
Possible completions:
metric OSPF default metric
metric-type OSPF metric type for default routes (default: 2)
route-map Specify route-map name to use
|
|
|
|
Added health-check to sync-group in CLI
Don't use instance health-check when instance in sync group member
Disallow wrong healtch-check configurations
New smoke test
|
|
T5504: Keepalived VRRP ability to set more than one peer-address
|
|
|
|
Added health-check to sync-group in CLI
Don't use instance health-check when instance in sync group member
Disallow wrong healtch-check configurations
New smoke test
|
|
required
|
|
remove obsolete imports
|
|
for leases
|
|
This extends commit dbe8c613b ("bridge: T6043: do not call vxlan dependency if
interface does not exist (yet)") with a proper cleanup of additional interfaces
created during the testrun.
|
|
In order to keep the proper priority list during system startup and on initial
setup/commit for this feature the dependent VXLAN code should not be called,
if the interface in question does not exist (yet).
|
|
login: T5972: add possibility to disable individual local user accounts
|
|
* set system login user <name> disable
|
|
T6001: add option to disable next-hop-tracking resolve-via-default
|
|
context
* set vrf name <name> ip nht no-resolve-via-default
* set vrf name <name> ipv6 nht no-resolve-via-default
|
|
* set system ip nht no-resolve-via-default
* set system ipv6 nht no-resolve-via-default
|
|
T6029: Rewritten Accel-PPP services to an identical feature set
|
|
Removed dhcp-interface option (l2tp)
Added wins-server (sstp)
Added description (ipoe, pppoe, sstp, pptp)
Added exteded-script (l2tp, sstp, pptp)
Added shaper (ipoe, pptp, sstp, l2tp)
Added limits (ipoe, pptp, sstp, l2tp)
Added snmp ( ipoe, pptp,sstp, l2tp)
Refactoring and reformated code.
|
|
Commit 0eb4168aa ("eigrp: T2472: improve code for later tests") added a basic
smoketest for EIGRP, which is also run by the CI hence not having a +x bit at
all.
This just deletes the basic smoketest testing for ASN and EIGRP router-id.
We can revert it once it's fixed in FRR upstream.
https://github.com/FRRouting/frr/pull/14765
|
|
|
|
After updateing netfilter in the commit https://github.com/vyos/vyos-build/commit/b31f5fe934bcb37534d49acdb5f7756bf05422e8
The nftables format for conntrack timeouts is different.
Fix this.
|
