| Age | Commit message (Collapse) | Author |
|---|
|
In this commit we add OSPF segment routing, smoke tests, handlers,
FRR template changes, and CLI commands.
|
|
Section.interfaces() now as an option if it should return also VLAN interfaces
or not. No need to keep a custom logic for it.
|
|
Changed CLI syntax in route-map set community,
set large-community, set extcommunity
Allows to add multiple communities, large-communities
and extcommunities in clear view.
Added new well-known communities.
Added non-transitive feature in extcommunities.
Fixed community's validators.
|
|
T4700: Firewall: add interface matching criteria
|
|
The initial implementation from commit ac4e07f9 ("rfs: T4689: Support RFS
(Receive Flow Steering)") always adjusted the global rps_sock_flow_entries
configuration. So if RFS was enabled for one NIC but not the other - it did not
work.
According to the documentation:
RFS is only available if the kconfig symbol CONFIG_RPS is enabled (on by
default for SMP). The functionality remains disabled until explicitly
configured. The number of entries in the global flow table is set through:
/proc/sys/net/core/rps_sock_flow_entries
The number of entries in the per-queue flow table are set through:
/sys/class/net/<dev>/queues/rx-<n>/rps_flow_cnt
Both of these need to be set before RFS is enabled for a receive queue. Values
for both are rounded up to the nearest power of two. The suggested flow count
depends on the expected number of active connections at any given time, which
may be significantly less than the number of open connections. We have found
that a value of 32768 for rps_sock_flow_entries works fairly well on a
moderately loaded server.
This commit sets rps_sock_flow_entries via sysctl on bootup leafing the RFS
configuration to the interface level.
|
|
ids: T4557: Migrate threshold and add new threshold types
|
|
Migrate "service ids ddos-protection threshold xxx" to
"service ids ddos-protection general threshold xxx"
Add new threshold types:
set service ids ddos-protection threshold tcp xxx
set service ids ddos-protection threshold udp xxx
set service ids ddos-protection threshold icmp xxx
|
|
|
|
|
|
nat: nat66: T4605: T4706: Refactor NAT/NAT66 and use new table name
|
|
* Rename table to vyos_nat
* Add static NAT smoketest
|
|
* Rename table to vyos_nat
* Refactor tests to use `verify_nftables` format
|
|
* Rename table to vyos_nat
* Refactor tests to use `verify_nftables` format
|
|
T4699: Firewall: Add return action
|
|
|
|
In addition to the rewrite to make use of get_config_dict() the CLI is
slightly adjusted as specified in T4703.
* Rename vlan-id and vlan-range to simply vlan
* Rename network-mode to simply mode
* Re-use existing common Jinja2 template for Accel-PPP which are shared
with PPPoE and SSTP server.
* Retrieve default values via defaultValue XML node
|
|
As we change syntax for IPSec 'esp <tag> compression disable'
to delete 'compression' if it not used, so delete it from nhtp
test
|
|
T4699: Firewall: Add jump action in firewall ruleset
|
|
|
|
The initial Accel-PPP PPPoE implementation used:
set service pppoe-server interface <name> vlan-id <id>
set service pppoe-server interface <name> vlan-range <start-stop>
This is actually a duplicated CLI node.
|
|
ipsec: T4118: Change vpn ipsec syntax for IKE ESP and peer
|
|
|
|
Migration and Change boolean nodes "enable/disable" to
disable-xxxx, enable-xxxx and just xxx for VPN IPsec
configurations
- IKE changes:
- replace 'ipsec ike-group <tag> mobike disable'
=> 'ipsec ike-group <tag> disable-mobike'
- replace 'ipsec ike-group <tag> ikev2-reauth yes|no'
=> 'ipsec ike-group <tag> ikev2-reauth'
- ESP changes:
- replace 'ipsec esp-group <tag> compression enable'
=> 'ipsec esp-group <tag> compression'
- PEER changes:
- replace: 'peer <tag> id xxx'
=> 'peer <tag> local-id xxx'
- replace: 'peer <tag> force-encapsulation enable'
=> 'peer <tag> force-udp-encapsulation'
- add option: 'peer <tag> remote-address x.x.x.x'
Add 'peer <name> remote-address <name>' via migration script
|
|
Add new VyOS CLI command:
set protocols bgp parameters bestpath peer-type multipath-relax
This command specifies that BGP decision process should consider paths from all
peers for multipath computation. If this option is enabled, paths learned from
any of eBGP, iBGP, or confederation neighbors will be multipath if they are
otherwise considered equal cost. [1]
[1]: http://docs.frrouting.org/en/stable-8.3/bgp.html#clicmd-bgp-bestpath-peer-type-multipath-relax
|
|
In addition to verify the queue lengths when CLI option is set, we also need
to verify that all values are resetted back to "0" which is the Kernel default.
|
|
* 'T4689' of https://github.com/jack9603301/vyos-1x:
rfs: T4689: Support RFS(Receive Flow Steering)
|
|
|
|
|
|
The old value of 1024 is no longer supported by the most recent Kernel
|
|
|
|
firewall: zone-policy: T2199: T4605: Refactor firewall, migrate zone-policy
|
|
This change is to fix a bug in which ISIS segment routing was broken due to a refactor.
This change also is going to introduce a smoketest to make sure this is caught in the future.
|
|
|
|
|
|
|
|
firewall node
* Refactor firewall and zone-policy rule creation and cleanup
* Migrate interface firewall values to `firewall interfaces <name> <direction> name/ipv6-name <name>`
* Remove `firewall-interface.py` conf script
|
|
This reverts commit 53355271a2864d844daca89a064c21e514e10adb.
|
|
|
|
firewall and in policy route
|
|
Matching criteria added: ttl/hoplimit and packet-length
|
|
|
|
|
|
* 'T4651' of https://github.com/nicolas-fort/vyos-1x:
Firewall: T4651: Change proposed cli from ip-length to packet-length
Firewall: T4651: Add options to match packet size on firewall rules.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This reverts commit fa91f567b7b5f009aaaed569b3f5e5db4b638d39.
|
