Age | Commit message (Collapse) | Author |
|
After commit cc7ba8824 ('vxlan: T5699: migrate "external" CLI know to
"parameters external"') We also need to adjust the testcase for ARP/ND
suppression.
|
|
This extends commit 6248b2ae1 ("T5558: smoketest: fix nat definitions on
dialup-router-medium-vpn") that missed out eth1 interface.
|
|
vxlan: T5668: add CLI knob to enable ARP/ND suppression
|
|
vxlan: T5699: migrate "external" CLI know to "parameters external"
|
|
As we have a bunch of options under "paramteres" already and "external" is
clearly one of them it should be migrated under that node as well.
|
|
In order to minimize the flooding of ARP and ND messages in the VXLAN network,
EVPN includes provisions [1] that allow participating VTEPs to suppress such
messages in case they know the MAC-IP binding and can reply on behalf of the
remote host. In Linux, the above is implemented in the bridge driver using a
per-port option called "neigh_suppress" that was added in kernel version 4.15.
[1] https://www.rfc-editor.org/rfc/rfc7432#section-10
|
|
|
|
set interfaces bonding bond10 evpn es-df-pref '50'
set interfaces bonding bond10 evpn es-id '10'
set interfaces bonding bond10 evpn es-sys-mac '01:23:45:67:89:ab'
set interfaces bonding bond10 member interface 'eth3'
set interfaces bonding bond10 mode '802.3ad'
|
|
|
|
(valid for interfaces and groups) in firewal, nat and nat66.
|
|
T5643: nat: add interface-groups to nat. Use same cli structure for i…
|
|
T5299: Add missed option ceiling for QoS shaper
|
|
vxlan: T5671: change port to IANA assigned default port
|
|
Add missed option `ceil` for QoS class 'trafficshaper'
|
|
|
|
Currently VyOS VXLAN implementation uses the Linux assigned port 8472 that
predates the IANA assignment. As Most other vendors use the IANA assigned port,
follow this guideline and use the new default port 4789.
Existing configuration not defining an explicit port number will be migrated
to the old default port number of 8472, keeping existing configurations work!
|
|
|
|
T5541: firewall zone: re add firewall zone-base firewall
|
|
T5637: add new rule at the end of base chains for default-actions and log capabilities
|
|
As `providers legacy default` option was deleted with
insecure DES and Blowfish ciphers, the smoketest cannot pass
without adding encyption ciphers
Otherwise
Oct 16 09:41:34 r4 openvpn-vtun5[9648]: DCO version: N/A
Oct 16 09:41:34 r4 openvpn-vtun5[9648]: Cipher BF-CBC not supported
Oct 16 09:41:34 r4 openvpn-vtun5[9648]: Exiting due to fatal error
Fix the smoketest
|
|
|
|
interface-name|interface-group as in firewall.
|
|
T5165: Implement policy local-route source and destination port
|
|
T5530: isis: Adding loop free alternate feature
|
|
pppoe: T5630: allow to specify MRU in addition to already configurable MTU
|
|
enables log capabilities for default-action in base chains. And of course, add option for enabling log for default-action
|
|
Add `policy local-route` source and destination port
set policy local-route rule 23 destination port '222'
set policy local-route rule 23 protocol 'tcp'
set policy local-route rule 23 set table '123'
set policy local-route rule 23 source port '8888'
% ip rule show prio 23
23: from all ipproto tcp sport 8888 dport 222 lookup 123
|
|
|
|
|
|
|
|
Set the MRU (Maximum Receive Unit) value to n. PPPd will ask the peer to send
packets of no more than n bytes. The value of n must be between 128 and 16384,
the default was always 1492 to match PPPoE MTU.
A value of 296 works well on very slow links (40 bytes for TCP/IP header + 256
bytes of data). Note that for the IPv6 protocol, the MRU must be at least 1280.
CLI:
set interfaces pppoe pppoe0 mru 1280
|
|
|
|
Add support for per-service cache management for ddclient providers
via `wait-time` and `expiry-time` options. This allows for finer-grained
control over how often a service is updated and how long the hostname
will be cached before being marked expired in ddclient's cache.
More specifically, `wait-time` controls how often ddclient will attempt
to check for a change in the hostname's IP address, and `expiry-time`
controls how often ddclient to a forced update of the hostname's IP
address.
These options intentionally don't have any default values because they
are provider-specific. They get treated similar to the other provider-
specific options in that they are only used if defined.
|
|
T5165: Migrate policy local-route rule x destination to address
|
|
ddclient: T5612: Miscellaneous improvements and fixes for dynamic DNS
|
|
Migrate policy local-route <destination|source> to node address
replace 'policy local-route{v6} rule <tag> destination|source <x.x.x.x>'
=> 'policy local-route{v6} rule <tag> destination|source address <x.x.x.x>'
|
|
filter and in policy route.
|
|
This commit adds a new configuration option to the mDNS repeater service
to allow controlling which IP version to use for mDNS repeater.
Additionally, publishing AAAA record over IPv4 and A record over IPv6 is
disabled as suggested.
See:
- https://github.com/lathiat/avahi/issues/117#issuecomment-1651475104
- https://bugzilla.redhat.com/show_bug.cgi?id=669627#c2
|
|
T5217: Add firewall synproxy
|
|
conntrack: T5376: T5598: Restore kernel conntrack helpers
|
|
firewall: T5614: Add support for matching on conntrack helper
|
|
ipsec: T5606: Add support for whole CA chains
|
|
Add option `protocol` for policy local-route
set policy local-route rule 100 destination '192.0.2.12'
set policy local-route rule 100 protocol 'tcp'
set policy local-route rule 100 set table '100'
|
|
`nf_conntrack_helper` that auto-assigned helpers is removed from the kernel
|
|
|
|
Also includes an update to smoketest to verify
|
|
Additional cleanup and refactoring for ddclient scripts including the
smotektests.
|
|
Some porvides (like 'namecheap') allow to use '@' or '*' as hostname
prefix for apex and wildcard records. This commit relaxes the hostname
validation to allow these prefixes.
|
|
Enable TTL support for web-service based protocols in addition to
RFC2136 based (nsupdate) protocol.
Since TTL is not supported by all protocols, and thus cannot have a
configuration default, the existing XML snippet `include/dns/time-to-live.xml.i`
does not have common `<defaultValue>300</defaultValue>` anymore and is
instead added explicitly whenever necessary.
|
|
Fix VRF support interface definition and configuration mode for ddclient
to actually capture the VRF name and pass it to the template.
|