| Age | Commit message (Collapse) | Author |
|---|
|
It is easier to backport the entire vyos.ifconfig library from 1.4 instead of
backporting single pieces which are required to add new feature to the tunnel
interface section.
In addition that both libraries are now back in sync it will become much easier
to backport any other new feature introduced in VyOS 1.4!
|
|
(cherry picked from commit ea4c72ed0dbcee3f7e8f9693c5310190833651d8)
|
|
Using an MTU less then the required 1280 bytes (as per RFC) on an interface
where IPv6 is not explicitly disabled by:
- set interfaces ethernet eth1 ipv6 address no-default-link-local
- not having any other IPv6 address configured
Will now trigger a commit error via verify() instead of raising
FileNotFoundError!
|
|
A lot of derived classes from Interface implemented their own get_config()
method which more or less was the same everywhere. We also hat different
qualifiers like @staticmethod or @classmethod.
This is now changed to only have the @classmethod in Interface base class which
will return the necessary dictionary keys for the required interfaces. This
change is a mid reduction in lines of code which is always a very nice thing!
|
|
|
|
|
|
The current VyOS CLI parser code written in Python contains a ton of duplicates
which I can also hold myself accountable for - or maybe mainly me - depends on
the angle of judge.
|
|
l2tpv3, wireguard, wirelessmodem, nat all require additional Kernel modules
to be present on the system. Each and every interface implemented their own
way of loading a module - by copying code.
Use a generic function, vyos.util.check_kmod() to load any arbitrary kernel
module passed as string or list.
|
|
airbag must now be explicitly installed.
the patch also allow to fully disables the installation of the logging
code at setup (and not just installing and doing nothing)
|
|
To make SLAAC and DHCPv6 work when forwarding=1, accept_ra must be 2
(default for accept_ra is 1).
|
|
- make error output more user friendly
- replace .format with f-strings
- split into lines less than ~80 characters long
|
|
Previously, the interface was always deleted and recreated, which
removed it from the bridge.
- always re-add the interface back to any bridge it is part of in
case it is deleted and recreated
|
|
Bridge members should not have any addresses assigned.
|
|
|
|
interfaces: T2362: IPv6 link-local and EUI64 address fixes
|
|
|
|
|
|
|
|
|
|
|
|
Commit 0e19d622a0410 ("bridge: T2232: move helper to vyos.validate") added a
new key to the dictionary but missed out the required "," at the end.
|
|
|
|
os.system does print the ouput of the command, run() does not.
A new function called call() does the printing and return the error code.
|
|
Interfaces enslaved to a bridge are not allowed to be deleted. If an interface
is deleted from the config but it is still enslaved to a bridge will cause a
configuration error on the subsequent boot.
|
|
|
|
As little change a possible but the function call
The behaviour should be totally unchanged.
|
|
|
|
Autoconfigure addresses using Prefix Information in Router Advertisements.
|
|
|
|
... to new XML and Python based frontend/backend.
|
|
The Interface get_state/set_state were not clear about
if they edited the admin or operational state.
functions are now using admin_state and oper_state
for clarity.
|
|
|
|
os.environ['VYOS_TAGNODE_VALUE']
This has been only a theoretical problem but then the error condition was
triggered - only an error has been printed instead of raising an Exception.
|
|
Provides a way to pass options to interface consistent between
subclasses of Interface
|
|
|
|
Tested using:
R1:
---
set interfaces l2tpv3 l2tpeth10 address '2001:db8:beef::1/64'
set interfaces l2tpv3 l2tpeth10 address '100.0.0.1/24'
set interfaces l2tpv3 l2tpeth10 destination-port '3000'
set interfaces l2tpv3 l2tpeth10 encapsulation 'udp'
set interfaces l2tpv3 l2tpeth10 local-ip '172.18.201.10'
set interfaces l2tpv3 l2tpeth10 peer-session-id '10'
set interfaces l2tpv3 l2tpeth10 peer-tunnel-id '100'
set interfaces l2tpv3 l2tpeth10 remote-ip '172.18.204.10'
set interfaces l2tpv3 l2tpeth10 session-id '20'
set interfaces l2tpv3 l2tpeth10 source-port '6000'
set interfaces l2tpv3 l2tpeth10 tunnel-id '200'
R2:
---
set interfaces l2tpv3 l2tpeth10 address '2001:db8:beef::2/64'
set interfaces l2tpv3 l2tpeth10 address '100.0.0.2/24'
set interfaces l2tpv3 l2tpeth10 destination-port '6000'
set interfaces l2tpv3 l2tpeth10 encapsulation 'udp'
set interfaces l2tpv3 l2tpeth10 local-ip '172.18.204.10'
set interfaces l2tpv3 l2tpeth10 peer-session-id '20'
set interfaces l2tpv3 l2tpeth10 peer-tunnel-id '200'
set interfaces l2tpv3 l2tpeth10 remote-ip '172.18.201.10'
set interfaces l2tpv3 l2tpeth10 session-id '10'
set interfaces l2tpv3 l2tpeth10 source-port '3000'
set interfaces l2tpv3 l2tpeth10 tunnel-id '100'
|
