| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Add new CLI command:
* "set protocols ospf redistribute table <n>"
|
|
Commit 6f87d8c9 ("ospf: T3757: support to configure area at an interface level")
did not allow the old way an area and netwokr was set-up as the if
expression was missing a check if 'area' was set in both the interface and the
ospf process.
|
|
FRR supports configuring either network prefixes per area, or assign an
interface to an area to participate in the routing process. This is already well
known from other venders and supported by FRR.
A valid VyOS OSPF configuration would then look like:
vyos@vyos# show protocols
ospf {
interface dum0 {
area 0
}
interface eth0.201 {
area 0
authentication {
md5 {
key-id 10 {
md5-key vyos
}
}
}
dead-interval 40
hello-interval 10
priority 1
retransmit-interval 5
transmit-delay 1
}
log-adjacency-changes {
detail
}
parameters {
abr-type cisco
router-id 172.18.254.201
}
passive-interface default
passive-interface-exclude eth0.201
}
|
|
|
|
|
|
Commit 4f9aa30f ("vrf: bgp: T3523: add route-map support for kernel routes")
added the possibility to also filter BGP routes towards the OS kernel, but the
smoketests failed. Reason was a non working CLI command applied to bgpd.
Thus the VRF route-map and the BGP configuration is now split into two templates,
one to be used for each daemon (zebra and bgpd).
Nevertheless one more bug was found in vyos.frr which currently does not suppoort
calling modify_section() inside a configuration "block". See [1] for more info.
[1]: https://phabricator.vyos.net/T3529
|
|
route-map
|
|
|
|
Removing the Zebra/Linux Kernel route-map added by "set protocols ospf route-map"
was not removed once applied. This was because the removal must happen within
the zebra daemon and not ospfd.
|
|
The introduction of key_mangling=('-', '_') when working with get_config_dict()
caused more harm then good. This commit extends common helpers and adds new
helpers when verifying the existence of route-maps, access-lists or prefix-lists.
|
|
|
|
|
|
Instead of multiple if/else paths, use a common vrf string variable which is
either populated or not. In addtion when interfaces are configured for a given
VRF, harden the regex for config reload.
|
|
|
|
During assembly of the required config changes we also must move the
interfaces_removed assignemnt to an earlier stage so the value is also populated
when the entire process is removed to cleanup all remaining OSPF process assigned
interfaces.
This was yet not the case and when deleting OSPF I still got my "interface eth0"
with the area key configured.
|
|
|
|
Instead of having the dynamic routing protocols OSPF and BGP residing under
the "protocols vrf <name> [ospf|bgp]" nodes, rather move them directly under
the "vrf name <name> protocols [ospf|bgp]" node. Now all VRF related parts
are placed under the same root node.
This eases the verify steps tremendously, as we do not need to check wheter a
VRF eists or not, it will always exist as we operate under a child node.
|
|
VyOS CLI config:
vrf red {
ospf {
default-information {
originate {
always
}
}
default-metric 30
passive-interface default
}
}
Will create the FRR configuration snippet:
!
router ospf vrf red
auto-cost reference-bandwidth 100
timers throttle spf 200 1000 10000
passive-interface default
default-metric 30
default-information originate always
!
|
|
|
|
|
|
|
|
With commit 015651a8 ("T2638: Enable more debugging in the FRR library") a
global debug mechanism was added by creating a file named /tmp/vyos.frr.debug.
With this change we can drop the duplicated debug code from every protocol.
|
|
Added "set protocols ospf interface eth1 hello-multiplier <n>" CLI command. This
is mutually exclusive to "set protocols ospf interface eth1 dead-interval <n>".
|
|
|
|
interface"
For easier maintenance and operability move the interface specific protocol
setting of OSPF to the OSPF protocol section. This is now also in-line with IS-IS.
This means to migrate:
ethernet eth0 {
vif 202 {
ip {
ospf {
authentication {
md5 {
key-id 10 {
md5-key vyosvyos
}
}
}
dead-interval 40
hello-interval 10
priority 1
retransmit-interval 5
transmit-delay 1
}
}
}
}
to
protocols {
ospf {
interface eth0.201 {
authentication {
md5 {
key-id 10 {
md5-key vyosvyos
}
}
}
dead-interval 40
hello-interval 10
priority 1
retransmit-interval 5
transmit-delay 1
}
}
|
|
A hyphen in a route-map name will be converted to _, take care about this
effect during validation.
|
|
|
|
This commit provides the implementation of the OSPF CLI with a Jinja2 template
that is loaded by FRR reload. It also contains some initial smoketests.
There is yet no verify() implementation!
|
|
|
|
|
|
|
