| Age | Commit message (Collapse) | Author |
|---|
|
|
|
Commit 6cffe2aa82 ("bgp: T4490: Add informational message for peer withour AFI")
only checked if an address-family is configured under the neighbor statement.
This is not enough as the AFI can also be specified via a peer-group.
Add a new verify_afi() helper that checks both the neighbor and the assigned
peer-group.
|
|
|
|
|
|
It makes no sense to enslave an interface to a bond or a bridge device if it is
bound to a given VRF. If VRFs should be used - the encapuslating/master
interface should be part of the VRF.
Error out if the member interface is part of a VRF.
|
|
VRF names: "add, all, broadcast, default, delete, dev, get, inet,
mtu, link, type, vrf" are reserved and cannot be used for vrf name
|
|
When is_member() is inspecting the bridge/Bond member interfaces it must work
with the real interface (e.g. eth1) under the "ethernet" node and not work on
the "member interface eth1" CLI tree, that makes no sense at all.
|
|
disable-directed-broadcast-forwarding"
|
|
Directed broadcast is described in rfc1812#section-5.3.5.2 and rfc2644.
By default Linux kernel doesn't forward directed broadcast
packets unless both of `/proc/sys/net/ipv4/conf/all/bc_forwarding`
and `/proc/sys/net/ipv4/conf/$iface/bc_forwarding` are set to 1.
|
|
As we have specific configuration for each plugin:
set service monitoring telegraf xxx
- azure-data-explorer
- prometheus-client
- splunk
We should to move configuration that related to influxdb under
influxdb node
Replace:
set service monitoring telegraf
- authentication xxx
- bucket xxx
- port xxx
- url
To:
set service monitoring telegraf influxdb xxx
|
|
|
|
After discussion with @zsdc this was decided the better long term fix
* Removes hourly logrotate cron in favour of systemd timer override
|
|
dns: T4509: Add dns64-prefix option
|
|
rfc6147: DNS Extensions for Network Address Translation
from IPv6 Clients to IPv4 Servers
set service dns forwarding dns64-prefix 2001:db8:aabb::/96
|
|
It makes no sense to test against a VRF that might not exist at all.
|
|
When clients only use DHCP for interface addressing we can not bind NTPd to
an address - as it will fail if the address changes. This commit adds support
to bind ntpd to a given interface in addition to a given address.
set system ntp interface <name>
|
|
dns: T4378: Allow wildcard A AAAA record with option all
|
|
Ability to set wildcard record for authoritative-domain
set authoritative-domain example.com records a any address 192.0.2.11
cat /run/powerdns/zone.example.com.conf
* 300 A 192.0.2.11
|
|
Add rate-limit options: attribute, muptiplier and vendor
set service ipoe-server auth radius rate-limit attribute 'Mikrotik-Rate-Limit'
set service ipoe-server auth radius rate-limit enable
set service ipoe-server auth radius rate-limit multiplier '0.001'
set service ipoe-server auth radius rate-limit vendor 'Miktorik'
|
|
|
|
* 'T4490' of https://github.com/sever-sever/vyos-1x:
bgp: T4490: Add informational message for peer withour AFI
|
|
openvpn: T4485: Accept multiple tls ca-certificate values
|
|
set service router-advert interface eth0 name-server-lifetime <value>
|
|
|
|
containers: T4473: Fix create container with not exist network
|
|
Fix correct path for removing containers and container networks
Reduce timoute from 10 (default) to 3 seconds for stopping
containers
|
|
Fix for setting container without or wrong network decalaration
|
|
As we don't use addresss-family ipv4-unicast by default we
should to send informational message about AFI for peer is required
|
|
|
|
|
|
* Refactor nftables clean-up code
* Adds policy route test for using firewall groups
|
|
|
|
firewall: T478: Add support for nesting groups
|
|
|
|
This reverts commit 6f818ee9033ee3abeedbed73eb44331dc27e7408.
|
|
It can be more then 5 symbols in top-level-domain address
for example '.photography' and '.accountants'
Firewall group can be added without address:
* set firewall group domain-group DOMAIN
Check if 'address' exists in group_config
|
|
|
|
* 'sstp_port' of https://github.com/goodNETnick/vyos-1x:
sstp: T4444. Port number changing support
|
|
firewall: T970: Add firewall group domain-group
|
|
event-handler: T3083: Add simple event-handler
|
|
Before:
set service event-handler Foo
After:
set service event-handler event Foo
|
|
* Added the ability to filter by a syslog identifier
* Added the ability to pass arguments to a script
* Added the ability to pass preconfigured environment variables to a script
* A message that triggered a script is now passed in the `message` variable and
can be used in a script
* Replaced `call()` to `run()`, since stdout are not need to be printed
|
|
Move 'system event-handler' to 'service event-handler'
|
|
* Removed dynamic generating for systemd unit
* Optimized configuration file deleting process
* Added exceptions handlers to event-handler script to protect service
from most obvious potential troubles
* Improved logging
* Moved pattern compilation outside a messages loop to avoid extra operations
* Added signal handlers for proper systemd integration
|
|
Event-handler allows executing a custom script when in logs it
detects configured "pattern"
A simple implemenation
set system event-handler first pattern '.*ssh2.*'
set system event-handler first script '/config/scripts/hello.sh'
|
|
|
|
OWAMP is a command line client application and a policy daemon used
to determine one way latencies between hosts.
OWAMP session control uses traditional client-server communication
between a control-client and a server,
TWAMP (two-way active measurement protocol)
Add configuration and operation modes
set service sla owamp-server
set service sla twamp-server
run force owping 192.0.2.120
run force twping 192.0.2.190
|
|
|
|
|
|
|
