| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
|
|
|
|
Only start console if it exists on the running system. If a user detaches a
USB serial console and reboots - it should not fail!
|
|
During testing it was discovered that there is a well known problem (we had for
ethernet interfaces) also in the serial port world. They will be enumerated and
mapped to /dev/ttyUSBxxx differently from boot to boot. This is especially
painful on my development APU4 board which also has a Sierra Wireless MC7710
LTE module installed.
The serial port will toggle between ttyUSB2 and ttyUSB5 depending on the
amount of serial port extenders attached (FT4232H).
The shipped udev rule (/usr/lib/udev/rules.d/60-serial.rules) partly solves
this by enumerating the devices into /dev/serial/by-id folder with their name
and serial number - it's a very good idea but I've found that not all of the
FT4232H dongles have a serial number programmed - this leads to the situation
that when you plug in two cables with both having serial number 0 - only one
device symlink will appear - the previous one is always overwritten by the
latter one.
Derive /usr/lib/udev/rules.d/60-serial.rules and create a /dev/serial/by-bus
directory and group devices by attached USB root port.
|
|
Migrate the serial console subsystem to XML and Python.
|
|
Commit 2cb806271928 ("wirelessmodem: T2241: make VRF and bond/bridge membership
mutually exclusive") added some logic which is not forseen/neither makes sense
on a dialup interface, thus it's removed again
|
|
... all information are present in journald.
|
|
During testing it was discovered that there is a well known problem (we had for
ethernet interfaces) also in the serial port world. They will be enumerated and
mapped to /dev/ttyUSBxxx differently from boot to boot. This is especially
painful on my development APU4 board which also has a Sierra Wireless MC7710
LTE module installed.
The serial port will toggle between ttyUSB2 and ttyUSB5 depending on the
amount of serial port extenders attached (FT4232H).
The shipped udev rule (/usr/lib/udev/rules.d/60-serial.rules) partly solves
this by enumerating the devices into /dev/serial/by-id folder with their name
and serial number - it's a very good idea but I've found that not all of the
FT4232H dongles have a serial number programmed - this leads to the situation
that when you plug in two cables with both having serial number 0 - only one
device symlink will appear - the previous one is always overwritten by the
latter one.
Derive /usr/lib/udev/rules.d/60-serial.rules and create a /dev/serial/by-bus
directory and group devices by attached USB root port.
vyos@vyos:~$ find /dev/serial/by-bus/ -name usb* -exec basename {} \; | sort
usb0b1.3p1.0
usb0b1.3p1.2
usb0b1.3p1.3
usb0b2.4p1.0
usb0b2.4p1.1
usb0b2.4p1.2
usb0b2.4p1.3
So we have USB root 0 with bus 1.3 and port 1.0. The enumeration is constant
accross reboots.
|
|
Retrieving the CLI nodes from current config was missed out and only
implemented for PPPoE.
|
|
openvpn: T2550: fix for IPv4 remote-host addresses
|
|
Commit bb9f998 added IPv6 support for OpenVPN, but IPv4 only
configurations stopped working (Address family for hostname not supported)
Commit fc467519 fixed some scenarios by using IPv4 protocols
if 'local-host' is IPv4 address, but the client mode is using
'remote-host' instead and was still broken.
This commit in addition to 'local-host' also checks all the
'remote-host' addresses.
|
|
bonding: T2527: delete the last interface from bond
|
|
|
|
|
|
|
|
airbag :T2088: make airbag explicit
|
|
airbag must now be explicitly installed.
the patch also allow to fully disables the installation of the logging
code at setup (and not just installing and doing nothing)
|
|
|
|
|
|
|
|
|
|
Some ISPs (e.g. Comcast) only delegate a /64 by default. You have to explicitly
"ask" for a bigger (e.g. /60) prefix. This commit adds a CLI node to request
a specific prefix length in the range 32 - 64.
dhcpv6-options {
prefix-delegation {
length 60
}
}
|
|
Rename the CLI nodes for prefix delegation from "dhcpv6-options delegate
<interface>" to "dhcpv6-options prefix-delegation interface <interface>".
The change is required to add the possibility to request for specific prefix
sized via the CLI. That option was not possible with the old configuration
tree.
|
|
Copy/paste error resulting in:
Traceback (most recent call last):
File "/usr/libexec/vyos/conf_mode/interfaces-ethernet.py", line 303, in <module>
apply(c)
File "/usr/libexec/vyos/conf_mode/interfaces-ethernet.py", line 205, in apply
e.dhcp.v6.options['dhcpv6_pd'] = e['dhcpv6_pd']
TypeError: 'EthernetIf' object is not subscriptable
|
|
|
|
|
|
|
|
|
|
|
|
Commit 39c53aadbf9e ("pppoe: T2488: remove logfile generation") accidently
missed a not in an if statement.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
With enabled encryption keys must be configured.
|
|
|
|
MACsec always talks about MKA (MACsec Key Agreement protocol) thus the node
should reflect that.
|
|
|
|
This is best suited as a key is required, too.
|
|
|
