| Age | Commit message (Collapse) | Author |
|---|
|
|
|
bracketize IPv6 remote address to avoid
Failed to parse: https://2001:db8::2/configure-section
|
|
Service config-sync allows synchronizing a section of
the configuration.
As PoC allow only nat, nat66 and firewall sections
Rertreive the configuration for a section from self node and
send this configuration to the section of the 'secondary' node.
This feature adds a symlink from helper 'vyos_config_sync.py'
to '/config/scripts/commit/post-hooks.d' and config that is
located in '/run/config_sync_conf.conf'
It will synchronyze the config only if the setcion
was changed.
set service config-sync secondary address 192.0.2.11
set service config-sync secondary key xxx
set service config-sync section nat
set service config-sync section nat66
set service config-sync section firewall
set service config-sync mode load
|
|
|
|
Add policy (any-available|all-available) for target checking for failover route
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check policy 'any-available'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '192.168.122.1'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '192.168.122.11'
It depends if we need that all targets must be alive on just one target.
|
|
There is only one target for checking ICMP/ARP
Extend it for checking multiple targets
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '203.0.113.1'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '203.0.113.11'
The route will be installed only if all targets are 'alive'
|
|
If there is no route in the routing table (requires install route)
it checks routing table and returns best route None
But if we have 2 routes to the same dest ip but with different
metrics it doesn't get None (not first route install)
It cause that bast metric route cannot be installed (wrong logic)
Add func "is_route_exists" and check route/gateway/metric for
the required route
|
|
routing: T1237: Add new feature failover route
|
|
Failover route allows to install static routes to the kernel routing
table only if required target or gateway is alive
When target or gateway doesn't respond for ICMP/ARP checks this route
deleted from the routing table
Routes are marked as protocol 'failover' (rt_protos)
cat /etc/iproute2/rt_protos.d/failover.conf
111 failover
ip route add 203.0.113.1 metric 2 via 192.0.2.1 dev eth0 proto failover
$ sudo ip route show proto failover
203.0.113.1 via 192.0.2.1 dev eth0 metric 1
So we can safely flush such routes
|
|
<name> interface <ifname>`
* Include refactor to policy route to allow for deletion of mangle table instead of complex cleanup
* T4605: Rename mangle table to vyos_mangle
|
|
|
|
`fqdn` node
|
|
|
|
|
|
|
|
|
|
Domain group allows to filter addresses by domain main
Resolved addresses as elements are stored to named "nft set"
that used in the nftables rules
Also added a dynamic "resolver" systemd daemon
vyos-domain-group-resolve.service which starts python script
for the domain-group addresses resolving by timeout 300 sec
set firewall group domain-group DOMAINS address 'example.com'
set firewall group domain-group DOMAINS address 'example.org'
set firewall name FOO rule 10 action 'drop'
set firewall name FOO rule 10 source group domain-group 'DOMAINS'
set interfaces ethernet eth0 firewall local name 'FOO'
nft list table ip filter
table ip filter {
set DOMAINS {
type ipv4_addr
flags interval
elements = { 192.0.2.1, 192.0.2.85,
203.0.113.55, 203.0.113.58 }
}
chain NAME_FOO {
ip saddr @DOMAINS counter packets 0 bytes 0 drop comment "FOO-10"
counter packets 0 bytes 0 return comment "FOO default-action accept"
}
}
|
|
This reverts commit 534f677d36285863decb2cdff179687b4fd690cb.
Revert while investigating failure in vyos-configtest.
|
|
This reverts commit c4d389488970c8510200cac96a67182e9333b891.
Revert while investigating failure in vyos-configtest.
|
|
This reverts commit 2a4b45ba7fa4dabf7e592f499cfb06a7ae38cdea.
Revert while investigating failure in vyos-configtest.
|
|
|
|
|
|
|
|
|
|
|
|
Use tempfile to avoid race conditions during virtual migration.
|
|
Add URL, token and bucket hidind data when is used function
"strip-private"
|
|
|
|
After commit ae16a51506c ("configquery: T3402: use vyatta-op-cmd-wrapper to
provide environment") we can now call VyOS op-mode commands from arbitrary
Python scripts.
|
|
(cherry picked from commit eb6247e4b464c36fa7441627b221d0db39429251)
|
|
With the rewrite of vyatta_net_name to Python using ConfigTree, one
runs into the change in the syntax of the component version string when
updating 1.2 --> 1.3/1.4, since the udev rule is run before the
migration of the config file; add an explicit 'virtual' migration on
configtree error.
|
|
(on behalf of Dmitriy Eshenko)
|
|
|
|
|
|
|
|
|
|
|
|
Extend regex used by the "| strip-private" modifier to remove the WireGuard
private key portion from stdout.
|
|
|
|
|
|
|
|
|
|
strip-private
|
|
|
|
|
|
|
|
|
|
|
|
|
|
This reverts commit 6086b7fa718f502563a17569abc81d4ccb94818c.
|
