Age | Commit message (Collapse) | Author |
|
T775: Config-sync bracketize IPv6 secondary address
|
|
|
|
bracketize IPv6 remote address to avoid
Failed to parse: https://2001:db8::2/configure-section
|
|
T775: Add service config-sync between 2 routers
|
|
VPP: T1797: Optimizations for VPP memory allocation during startup
|
|
- changed memory requirement from total to available. This allows to start on
systems with less total memory and protects from startup on systems with
overloaded memory.
- prevent startup if sysctl settings were not applied. This protects from
situations when the system cannot allocate enough hugepages or apply other
sysctl settings.
|
|
without vrf
|
|
isis: T5335: fix invalid isis config base in migration script
|
|
* set protocols ospf aggregation timer <seconds>
* set protocols ospf summary-address x.x.x.x/x [tag 1-4294967295]
* set protocols ospf summary-address x.x.x.x/x no-advertise
|
|
After an interface is added/removed from VPP, it will be reinitialized, which
allows reconfiguring IP addresses on it.
Also modified VPP load priority to start before interfaces, and avoid
reconfiguration during boot.
|
|
|
|
Interface may not be present in the op-mode dictionary, it cause
KeyError: 'interface' for policy route
|
|
T1797: VPP verify minimal installed memory and apply sysctl
|
|
Do not allow configure VPP if on the systems with low amount
installed memory
Add sysctl VPP parameters (hugepages, kernel.shmmax)
|
|
|
|
Service config-sync allows synchronizing a section of
the configuration.
As PoC allow only nat, nat66 and firewall sections
Rertreive the configuration for a section from self node and
send this configuration to the section of the 'secondary' node.
This feature adds a symlink from helper 'vyos_config_sync.py'
to '/config/scripts/commit/post-hooks.d' and config that is
located in '/run/config_sync_conf.conf'
It will synchronyze the config only if the setcion
was changed.
set service config-sync secondary address 192.0.2.11
set service config-sync secondary key xxx
set service config-sync section nat
set service config-sync section nat66
set service config-sync section firewall
set service config-sync mode load
|
|
T1797: Add initial vpp configuration
|
|
- added extra renaming operation to be sure that interface has the same name as
before in the system after it was moved from VPP to kernel
- added extra check after PCI device removal/adding
- added check for proper `retval` for CPI calls where it is available
- replaced empty return with an error in `_get_pci_address_by_interface()`
because not resolved address will lead to inconsistency of the system later
|
|
The previous implementation did not iterate over the communit list, so only
one match criteria was supported.
set policy route-map FOO rule 10 action 'permit'
set policy route-map FOO rule 10 set extcommunity rt '1111:2222222'
worked but on the other hand this failed:
set policy route-map FOO rule 20 action 'permit'
set policy route-map FOO rule 20 set extcommunity rt '6500:24 6500:23 192.168.0.1:111 192.168.0.1:222'
|
|
|
|
- added ability to add/remove interfaces without system reboot
- added `attempts` and `interval` to the VPP API connection. This is helpful in
case of high system load or when VPP was just started and API is not yet
available.
- added exceptions to API calls. This allows handling errors in communication
with API properly in conf-mode scripts.
- fixed PCI address search in VPP to match Linux kernel and ethtool style
- fixed systemd daemons control - first reload, then restart
- removed debug prints
- removed `vm.nr_hugepages` configuration. It is not required now but increases
RAM requirements a lot.
|
|
Use info from both ethtool and VPP to find PCI address for an
interface.
|
|
T5304: Container add volume bind propagation option
|
|
Replaced CLI commands with API calls.
CLI commands still can be used via:
```
vpp_control = VPPControl()
vpp_control.cli_cmd('command_here')
```
|
|
set container name c1 volume myvlm propagation rshared
|
|
Add initial configuration mode for VPP (PoC)
set vpp cpu corelist-workers '2'
set vpp cpu main-core '1'
set vpp interface eth1 num-rx-desc '256'
set vpp interface eth1 num-rx-queues '512'
set vpp interface eth1 num-tx-desc '256'
set vpp interface eth1 num-tx-queues '512'
set vpp interface eth1 pci '0000:02:00.0'
set vpp interface eth1 rx-mode 'polling'
set vpp interface eth2 pci '0000:08:00.0'
Limitation:
- 'set vpp interface ethX pci auto' works only per first
commit, then interface detached from default stack and creates
tun interface 'ethX' to communicate with default stack. In this
case we can't get PCI address via ethtool for 'tun' interfaces.
But we can set pci address manualy.
- Interface sync between default stack and VPP-DPDK stack
After vpp change it doesn't trigger iproute2 for changes
(should be written later)
I.e. if we change something in vpp per each commit it restarts
vpp.service it gets empty interface config as we don't configure vpp
directly and it should be configured via iproute2
But then if we do any change on interface (for example description)
it gets IP address, MTU, state, etc.
|
|
|
|
Check upper bound as defined in Debian Policy Manual. Without this
check, user 'nobody' will not be available.
|
|
|
|
|
|
|
|
|
|
|
|
warning: ~ action is deprecated, consider using the 'stop' statement instead [v8.24.0 try http://www.rsyslog.com/e/2307 ]
|
|
http-api: T5248: set/load config sections as JSON via API
|
|
... this is a step towards a new and better implementation that will utilize
VPP.
|
|
frr.service startup and shutdown is now explicitly managed by
vyos-router, so remove the systemd management directive.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
T5231: Add op-mode for show reverse-proxy
|
|
T3472: Print warning when commit-confirm is run as regular user
|
|
dns: T5144: Improve dynamic dns monitor and log and miscellaneous updates
|
|
|
|
|
|
|
|
dns: T5144: Refactor smoke tests for dynamic dns operation
|