| Age | Commit message (Collapse) | Author |
|---|
|
|
|
This is a leftover after commit 0e050cb35 (isis: T3417: drop artificial "domain"
node identifying the IS-IS process name). Drop all references to "process"
variable.
Specifying:
set protocols isis interface eth1
set protocols isis net '49.0001.1921.6825.5255.00'
set protocols isis redistribute ipv4 bgp
Triggered an exception
Traceback (most recent call last):
File "/usr/libexec/vyos/conf_mode/protocols_isis.py", line 309, in <module>
verify(c)
File "/usr/libexec/vyos/conf_mode/protocols_isis.py", line 158, in verify
f'"protocols isis {process} redistribute {afi} {proto}"!')
^^^^^^^
NameError: name 'process' is not defined
|
|
|
|
vti: T6085: interface is always down and only enabled by IPSec daemon
|
|
policy: T6130: Revert commit 960cace
|
|
* Move global state-policy smoketest to it's own test, verify conntrack
|
|
When a VTI interface is just created, it is in ADMIN UP state by default, even
if an IPSec peer is not connected. After the peer is disconnected the interface
goes to DOWN state as expected.
This breaks routing logic - for example, static routes through VTI interfaces
will be active even if a peer is not connected.
This changes to logic so ADMIN UP/DOWN state can only be changed by the
vti-up-down helper script.
Error was introduced during the Perl -> Python migration and move to the generic
vyos.ifconfig abstraction during the 1.4 development cycle.
|
|
This reverts commit 960cace189d7ace2bea0968646b1348b415e0363.
All community rules syntax was changed.
T5357 is invalid bug report.
VyOS cannot use new configuration syntax in the previous versions.
|
|
The op-mode command `show conntrack table ipv4` fails if gets a
conntrack entrie with `flowtable` offload. Those entries do not
have key `timeout`
```
File "/usr/libexec/vyos/op_mode/conntrack.py", line 115, in get_formatted_output
timeout = meta['timeout']
~~~~^^^^^^^^^^^
```
Use the timeout `n/a` for those offload conntrack entries
|
|
|
|
conntrack: T4022: add RTSP conntrack helper
|
|
T6121: Extend service config-sync to new sections
|
|
occurs also if only <policy route> is defined.
|
|
Extend `service config-sync` with new sections:
- LeafNodes: pki, policy, vpn, vrf (syncs the whole sections)
- Nodes: interfaces, protocols, service (syncs subsections)
In this cae the Node allows to uses the next level section
i.e subsection
For example any of the subsection of the node `interfaces`:
- set service config-sync section interfaces pseudo-ethernet
- set service config-sync section interfaces virtual-ethernet
Example of the config:
```
set service config-sync mode 'load'
set service config-sync secondary address '192.0.2.1'
set service config-sync secondary key 'xxx'
set service config-sync section firewall
set service config-sync section interfaces pseudo-ethernet
set service config-sync section interfaces virtual-ethernet
set service config-sync section nat
set service config-sync section nat66
set service config-sync section protocols static
set service config-sync section pki
set service config-sync section vrf
```
|
|
radvd: T6118: add nat64prefix support RFC8781
|
|
grub: T4548: Fixed GRUB configuration files order
|
|
To iterate files on ext* file systems GRUB reads their inodes one by one,
ignoring names. This breaks our configuration logic that relies on proper
loading order.
This commit adds a helper `sort_inodes()` that needs to be used whenever GRUB
configuration files are created. It recreates files, changing their inodes in a
way where inodes order matches alphabetical order.
|
|
Add support for pref64 option, as defined in RFC8781. The prefix valid lifetime
must not be smaller than the "interface interval max" definition which defaults
to 600.
set service router-advert interface eth1 nat64prefix 64:ff9b::/96
|
|
|
|
conntrack: T5080: Fix rule order for applied conntrack modules
|
|
|
|
|
|
firewall: T6071: truncate rule description field to 255 characters
|
|
|
|
dhcp: T6102: Fix clear DHCP lease op-mode
|
|
vrrp: T6020: vrrp health-check script not applied correctly
|
|
config: T4919: Add support for encrypted config with TPM
|
|
Re-implements https://github.com/vyos/vyatta-cfg-system/pull/194
|
|
Re-implements https://github.com/vyos/vyatta-cfg/pull/54
|
|
|
|
* Add `clear dhcpv6-server lease`
* Standardize using vyos.opmode
|
|
T6075: firewall and NAT: check if interface-group exists when using them in firewall|nat rules.
|
|
T6096: Config commits are not synced properly because 00vyos-sync is deleted by vyos-router
|
|
http-api: T6069: fix allocation outside of thread lock
|
|
Lower available CPU C states to a minimum if this option set. This will set
Kernel commandline options "intel_idle.max_cstate=0 processor.max_cstate=1".
|
|
|
|
firewall|nat rules.
|
|
by vyos-router
|
|
T6084: Add NHRP dependency for IPsec and fix NHRP empty config bug
|
|
If we have any `vpn ipsec` and `protocol nhrp` configuration we
get the empty configuration file `/run/opennhrp/opennhrp.conf`
after rebooting the system.
Use config dependency instead of the old `resync_nhrp` function
fixes this issue
|
|
|
|
|
|
Example:
vyos@vyos# set protocols ospfv3 redistribute bgp
Possible completions:
metric OSPF default metric
metric-type OSPF metric type for default routes (default: 2)
route-map Specify route-map name to use
|
|
dhcp-server: T6079: Disable duplicate static-mappings on migration
|
|
|
|
Added health-check to sync-group in CLI
Don't use instance health-check when instance in sync group member
Disallow wrong healtch-check configurations
New smoke test
|
|
configdep: T5839: remove trivially redundant config dependency calls
|
|
T5504: Keepalived VRRP ability to set more than one peer-address
|
|
banner: T6077: implement ASCII contest winner default logo
|
|
Added health-check to sync-group in CLI
Don't use instance health-check when instance in sync group member
Disallow wrong healtch-check configurations
New smoke test
|
