Age | Commit message (Collapse) | Author |
|
ocserv: T3896: add CLI options to configure ocserv config-per-user/group
|
|
T5219: ddclient: Allow not set login for Cloudflare API token
|
|
|
|
vrrp: T5215: fix the commit error when health check is not configured
|
|
|
|
that was replaced with Humps in all sciprts
|
|
T5158: Refactoring the commad sh interfaces counters
|
|
For more detailed information it's necessary to add information about drops and error counters.
|
|
T5215: add a built-in ping check for VRRP groups
|
|
|
|
Add RADIUS accounting-interim-interval option for PPTP-server
Specifies interval in seconds to send accounting information
(may be overridden by radius Acct-Interim-Interval attribute)
set vpn pptp remote-access authentication radius accounting-interim-interval '52'
|
|
Add RADIUS accounting-interim-interval option for L2TP-server
Specifies interval in seconds to send accounting information
(may be overridden by radius Acct-Interim-Interval attribute)
set vpn l2tp remote-access authentication radius accounting-interim-interval '120'
|
|
cloud-init: T5190: Added Cloud-init pre-configurator
|
|
T5060: Add disable option for high-availability
|
|
syslog: T2778: T2769: refactoring and VRF support
|
|
|
|
Allow syslog messages to be sent through a VRF (e.g. management).
|
|
|
|
Add 'maintenance mode' (option disable) for high-availability
set high-availability disable
|
|
dns: T5144: Improve dynamic DNS validations and completions
|
|
Use 'vyos-wan-load-balance.service' for load-balancing instead of
old start and stop 'vyatta-wanloadbalance.init' script
|
|
Add 'vyos-wan-load-balance.service' systemd unit for
'loadbalancing wan' instead of old vyatta-wanloadbalance.init script
|
|
|
|
|
|
|
|
Added a new service that starts before Cloud-init, waits for all network
interfaces initialization, and if requested by config, checks which interfaces
can get configuration via DHCP server and creates a corresponding Cloud-init
network configuration.
This protects from two situations:
* when Cloud-init tries to get meta-data via eth0 (default and fallback variant
for any data source which depends on network), but the real network is connected
to another interface
* when Cloud-init starts simultaneously with udev and initializes the first
interface to get meta-data before it is renamed to eth0 by udev
|
|
T5171: Use XML for loadbalancing wan instead of old templates
|
|
|
|
Use XML and python3 for 'load-balancing wan'
Use Jinja2 templates instead of old vyatta-wanloadbalance.pl to
generate configuration '/run/load-balance/wlb.conf' wich used by
/opt/vyatta/sbin/wan_lb
|
|
|
|
Without the change users might get confused as the setting is specified
on the VyOS CLI but never makes it to FRR due to an internal FRR check.
|
|
When we delete vrf vni there is a dictionary
{'only_vrf': 'red', 'new_frr_config': '!\n'}
|
|
conntrack-sync: T4888: rewrite the op mode script in the new format
|
|
Add verify() section to check if l3vni was removed in addition to the BGP
process under any given VRF.
|
|
|
|
|
|
|
|
FastAPI v0.92.0 (starlette v0.24.0) sets default attribute
Request._form; check for value == None instead of existence when
overriding Request class.
|
|
|
|
T1237: Failover route add policy for targets checking
|
|
dns: T5144: Make dns dynamic status output legacy format compatible
|
|
We must only search and replace for "vrf red" or "vrf green" - the regex
used infact matched on all VRFs which is wrong. This would remove all VRF VNI
configurations when only changing a single VRf.
|
|
ipsec: T5042: Rewritten 'show vpn ipsec remote-access' command
|
|
|
|
Add policy (any-available|all-available) for target checking for failover route
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check policy 'any-available'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '192.168.122.1'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '192.168.122.11'
It depends if we need that all targets must be alive on just one target.
|
|
Apply validations and completions to dynamic DNS protocols supported.
This also opens up additional protocols supported by ddclient 3.10.
Additional details:
- Validation and constraint have been added for interface names as well.
- While at it, the help texts got some copyedit and rewording.
|
|
Changes the node name from config-per-x to identity-based-config, as a result the j2 templates and vpn_openeconnect.py has been refactored to update the node name when accessing it's child nodes.
|
|
pki: T3642: Fix show command if no CA certs are present
|
|
op-mode: T5159: dhcpv6 incorrect warning message
|
|
The operational command "show dhcpv6 server leases" shows a warning message e
ven if dhcpv6 setting are configured and ipv6 address
got assigned to clients.
|