### Autogenerated by interfaces_wireless.py ### # see full documentation: # https://w1.fi/cgit/hostap/plain/wpa_supplicant/wpa_supplicant.conf network={ # ssid: SSID (mandatory); network name in one of the optional formats: # - an ASCII string with double quotation # - a hex string (two characters per octet of SSID) # - a printf-escaped ASCII string P"<escaped string>" # ssid="{{ ssid }}" # scan_ssid: # 0 = do not scan this SSID with specific Probe Request frames (default) # 1 = scan with SSID-specific Probe Request frames (this can be used to # find APs that do not accept broadcast SSID or use multiple SSIDs; # this will add latency to scanning, so enable this only when needed) scan_ssid=1 {% if security.wpa.passphrase is vyos_defined %} # ieee80211w: whether management frame protection is enabled # 0 = disabled (default unless changed with the global pmf parameter) # 1 = optional # 2 = required # The most common configuration options for this based on the PMF (protected # management frames) certification program are: # PMF enabled: ieee80211w=1 and key_mgmt=WPA-EAP WPA-EAP-SHA256 # PMF required: ieee80211w=2 and key_mgmt=WPA-EAP-SHA256 # (and similarly for WPA-PSK and WPA-PSK-SHA256 if WPA2-Personal is used) # WPA3-Personal-only mode: ieee80211w=2 and key_mgmt=SAE ieee80211w=1 # key_mgmt: list of accepted authenticated key management protocols # WPA-PSK = WPA pre-shared key (this requires 'psk' field) # WPA-EAP = WPA using EAP authentication # IEEE8021X = IEEE 802.1X using EAP authentication and (optionally) dynamically # generated WEP keys # NONE = WPA is not used; plaintext or static WEP could be used # WPA-NONE = WPA-None for IBSS (deprecated; use proto=RSN key_mgmt=WPA-PSK # instead) # FT-PSK = Fast BSS Transition (IEEE 802.11r) with pre-shared key # FT-EAP = Fast BSS Transition (IEEE 802.11r) with EAP authentication # FT-EAP-SHA384 = Fast BSS Transition (IEEE 802.11r) with EAP authentication # and using SHA384 # WPA-PSK-SHA256 = Like WPA-PSK but using stronger SHA256-based algorithms # WPA-EAP-SHA256 = Like WPA-EAP but using stronger SHA256-based algorithms # SAE = Simultaneous authentication of equals; pre-shared key/password -based # authentication with stronger security than WPA-PSK especially when using # not that strong password; a.k.a. WPA3-Personal # FT-SAE = SAE with FT # WPA-EAP-SUITE-B = Suite B 128-bit level # WPA-EAP-SUITE-B-192 = Suite B 192-bit level # OSEN = Hotspot 2.0 Rel 2 online signup connection # FILS-SHA256 = Fast Initial Link Setup with SHA256 # FILS-SHA384 = Fast Initial Link Setup with SHA384 # FT-FILS-SHA256 = FT and Fast Initial Link Setup with SHA256 # FT-FILS-SHA384 = FT and Fast Initial Link Setup with SHA384 # OWE = Opportunistic Wireless Encryption (a.k.a. Enhanced Open) # DPP = Device Provisioning Protocol # If not set, this defaults to: WPA-PSK WPA-EAP {% if security.wpa.mode is vyos_defined('wpa3') %} key_mgmt=SAE {% else %} key_mgmt=WPA-PSK WPA-PSK-SHA256 {% endif %} # psk: WPA preshared key; 256-bit pre-shared key # The key used in WPA-PSK mode can be entered either as 64 hex-digits, i.e., # 32 bytes or as an ASCII passphrase (in which case, the real PSK will be # generated using the passphrase and SSID). ASCII passphrase must be between # 8 and 63 characters (inclusive). ext:<name of external PSK field> format can # be used to indicate that the PSK/passphrase is stored in external storage. # This field is not needed, if WPA-EAP is used. # Note: Separate tool, wpa_passphrase, can be used to generate 256-bit keys # from ASCII passphrase. This process uses lot of CPU and wpa_supplicant # startup and reconfiguration time can be optimized by generating the PSK only # only when the passphrase or SSID has actually changed. psk="{{ security.wpa.passphrase }}" {% else %} key_mgmt=NONE {% endif %} }