Wireless (WiFi/WLAN) Network Interface 318 wlan[0-9]+ Wireless interface must be named wlanN wlanN Wireless (WiFi/WLAN) interface name #include HT and VHT capabilities for your card High Throughput (HT) settings 40MHz intolerance, use 20MHz only! Enable WMM-PS unscheduled automatic power save delivery [U-APSD] Supported channel set width ht20 ht40+ ht40- ht20 Supported channel set width both 20 MHz only ht40+ Supported channel set width both 20 MHz and 40 MHz with secondary channel above primary channel ht40- Supported channel set width both 20 MHz and 40 MHz with secondary channel below primary channel (ht20|ht40\+|ht40-) Enable HT-delayed block ack Enable DSSS_CCK-40 Enable HT-greenfield Enable LDPC coding capability Enable L-SIG TXOP protection capability Set maximum A-MSDU length 3839 7935 3839 Set maximum A-MSDU length to 3839 octets 7935 Set maximum A-MSDU length to 7935 octets (3839|7935) Short GI capabilities 20 40 20 Short GI for 20 MHz 40 Short GI for 40 MHz (20|40) Spatial Multiplexing Power Save (SMPS) settings static dynamic static STATIC Spatial Multiplexing (SM) Power Save dynamic DYNAMIC Spatial Multiplexing (SM) Power Save (static|dynamic) Support for sending and receiving PPDU using STBC (Space Time Block Coding) Enable receiving PPDU using STBC (Space Time Block Coding) [1-3]+ Number of spacial streams that can use RX STBC [1-3]+ Invalid capability item Enable sending PPDU using STBC (Space Time Block Coding) Require stations to support HT PHY Very High Throughput (VHT) settings Number of antennas on this card u32:1-8 Number of antennas for this card Set if antenna pattern does not change during the lifetime of an association VHT beamforming capabilities single-user-beamformer single-user-beamformee multi-user-beamformer multi-user-beamformee single-user-beamformer Support for operation as single user beamformer single-user-beamformee Support for operation as single user beamformee multi-user-beamformer Support for operation as multi user beamformer multi-user-beamformee Support for operation as multi user beamformee (single-user-beamformer|single-user-beamformee|multi-user-beamformer|multi-user-beamformee) VHT operating channel center frequency VHT operating channel center frequency - center freq 1 (for use with 80, 80+80 and 160 modes) u32:34-173 5Ghz (802.11 a/h/j/n/ac) center channel index (use 42 for primary 80MHz channel 36) Channel center value must be between 34 and 173 VHT operating channel center frequency - center freq 2 (for use with the 80+80 mode) u32:34-173 5Ghz (802.11 ac) center channel index (use 58 for secondary 80MHz channel 52) Channel center value must be between 34 and 173 VHT operating Channel width 0 1 2 3 0 20 or 40 MHz channel width 1 80 MHz channel width 2 160 MHz channel width 3 80+80 MHz channel width Enable LDPC (Low Density Parity Check) coding capability VHT link adaptation capabilities unsolicited both unsolicited Station provides only unsolicited VHT MFB both Station can provide VHT MFB in response to VHT MRQ and unsolicited VHT MFB (unsolicited|both) Invalid capability item Set the maximum length of A-MPDU pre-EOF padding that the station can receive u32:0-7 Maximum length of A-MPDU pre-EOF padding = 2 pow(13 + x) -1 octets Increase Maximum MPDU length to 7991 or 11454 octets (otherwise: 3895 octets) 7991 11454 7991 ncrease Maximum MPDU length to 7991 octets 11454 ncrease Maximum MPDU length to 11454 octets (7991|11454) Short GI capabilities 80 160 80 Short GI for 80 MHz 160 Short GI for 160 MHz (80|160) Support for sending and receiving PPDU using STBC (Space Time Block Coding) Enable receiving PPDU using STBC (Space Time Block Coding) [1-4]+ Number of spacial streams that can use RX STBC [1-4]+ Invalid capability item Enable sending PPDU using STBC (Space Time Block Coding) Enable VHT TXOP Power Save Mode Station supports receiving VHT variant HT Control field Require stations to support VHT PHY High Efficiency (HE) settings HE operating channel width 131 132 133 134 135 131 20 MHz channel width 132 40 MHz channel width 133 80 MHz channel width 134 160 MHz channel width 135 80+80 MHz channel width (131|132|133|134|135) HE operating channel center frequency HE operating channel center frequency - center freq 1 (for use with 80, 80+80 and 160 modes) u32:1-233 6Ghz (802.11 ax) center channel index (use 3 (at 40MHz), 7 (at 80MHz) or 15 (at 160MHz) for primary channel 1) Channel center value must be between 1 and 233 HE operating channel center frequency - center freq 2 (for use with the 80+80 mode) u32:1-233 6Ghz (802.11 ax) center channel index (use 23 (at 80MHz) for secondary channel 17) Channel center value must be between 1 and 233 Tell the AP that antenna positions are fixed and will not change during the lifetime of an association HE beamforming capabilities Support for operation as single user beamformer Support for operation as single user beamformee Support for operation as multi user beamformer BSS coloring helps to prevent channel jamming when multiple APs use the same channels Require stations to support HE PHY Wireless radio channel 0 Automatic Channel Selection (ACS) u32:1-14 2.4Ghz (802.11 b/g/n) Channel u32:34-173 5Ghz (802.11 a/h/j/n/ac) Channel u32:1-233 6Ghz (802.11 ax) Channel 0 #include #include #include Disable broadcast of SSID from access-point #include #include #include Disassociate stations based on excessive transmission failures #include #include #include Isolate stations on the AP so they cannot see each other #include Maximum number of wireless radio stations. Excess stations will be rejected upon authentication request. u32:1-2007 Number of allowed stations Number of stations must be between 1 and 2007 Stationary AP config indicates that the AP doesn't move. Management Frame Protection (MFP) according to IEEE 802.11w disabled optional required disabled no MFP optional MFP optional required MFP enforced (mandatory for WPA3) (disabled|optional|required) disabled Beacon Protection: management frame protection for Beacon frames, requires Management Frame Protection (MFP) disabled Wireless radio mode a b g n ac ax a 802.11a - 54 Mbits/sec b 802.11b - 11 Mbits/sec g 802.11g - 54 Mbits/sec n 802.11n - 600 Mbits/sec ac 802.11ac - 1300 Mbits/sec ax 802.11ax (6GHz only for now) (a|b|g|n|ac|ax) g #include Wireless physical device phy0 Transmission power reduction in dBm u32:0-255 TX power reduction in dBm dBm value must be between 0 and 255 Wireless security settings Basic Service Set Identifier (BSSID) ([0-9a-fA-F]{2}:){5}[0-9a-fA-F]{2} Invalid BSSID Station MAC address based authentication Select security operation mode accept deny accept Accept all clients unless found in deny list deny Deny all clients unless found in accept list (accept|deny) accept Accept station MAC address #include Deny station MAC address #include Wired Equivalent Privacy (WEP) parameters WEP encryption key txt Wired Equivalent Privacy key ([a-fA-F0-9]{10}|[a-fA-F0-9]{26}|[a-fA-F0-9]{32}) Invalid WEP key Wifi Protected Access (WPA) parameters Cipher suite for WPA unicast packets GCMP-256 GCMP CCMP-256 CCMP TKIP GCMP-256 AES in Galois/counter mode with 256-bit key GCMP AES in Galois/counter mode with 128-bit key CCMP-256 AES in Counter mode with CBC-MAC with 256-bit key CCMP AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] (supported on all WPA2 APs) TKIP Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] (GCMP-256|GCMP|CCMP-256|CCMP|TKIP) Invalid cipher selection Cipher suite for WPA multicast and broadcast packets GCMP-256 GCMP CCMP-256 CCMP TKIP GCMP-256 AES in Galois/counter mode with 256-bit key GCMP AES in Galois/counter mode with 128-bit key CCMP-256 AES in Counter mode with CBC-MAC with 256-bit key CCMP AES in Counter mode with CBC-MAC [RFC 3610, IEEE 802.11i/D7.0] (supported on all WPA2 APs) TKIP Temporal Key Integrity Protocol [IEEE 802.11i/D7.0] (GCMP-256|GCMP|CCMP-256|CCMP|TKIP) Invalid group cipher selection Group management cipher suite. All the stations connecting to the BSS will also need to support the selected cipher AES-128-CMAC BIP-CMAC-256 BIP-GMAC-128 BIP-GMAC-256 (AES-128-CMAC|BIP-CMAC-256|BIP-GMAC-128|BIP-GMAC-256) Invalid group management cipher selection AES-128-CMAC WPA mode wpa wpa2 wpa+wpa2 wpa3 wpa WPA (IEEE 802.11i/D3.0) wpa2 WPA2 (full IEEE 802.11i/RSN) wpa+wpa2 Allow both WPA and WPA2 wpa3 WPA3 (required for 802.11ax, you must also set mgmt-frame-protection as required) (wpa|wpa2|wpa\+wpa2|wpa3) Unknown WPA mode wpa+wpa2 #include WPA passphrase. If you are using special characters in the WPA passphrase then single quotes are required. txt Passphrase of at least 8 but not more than 63 printable characters for WPA-Personal and any passphrase for WPA-Enterprise .* Invalid WPA pass phrase, must be 8 to 63 printable characters! #include Enable RADIUS server to receive accounting info Wireless access-point service set identifier (SSID) .{1,32} Invalid SSID Wireless device type for this interface access-point station monitor access-point Access-point forwards packets between other nodes station Connects to another access point monitor Passively monitor all packets on the frequency/channel (access-point|station|monitor) Type must be access-point, station or monitor monitor #include #include #include #include