Updated document with the main information.

1 files changed, 1043 insertions, 0 deletions

diff --git a/docs/configexamples/dual-hub-dmvpn.rst b/docs/configexamples/dual-hub-dmvpn.rst
index f103972e..ea4d69f7 100644
--- a/docs/configexamples/dual-hub-dmvpn.rst
+++ b/docs/configexamples/dual-hub-dmvpn.rst
@@ -198,3 +198,1046 @@ ___________________________________
     set high-availability vrrp group HQ rfc3768-compatibility
     set high-availability vrrp group HQ virtual-address '192.168.0.254/24'
     set high-availability vrrp group HQ vrid '1'
+
+
+
+Step-3: DMVPN configuration between Hub and Spoke devices
+=========================================================
+
+This section provides an example configuration of the DMVPN enabled devices. 
+Hub devices are configured with static IPv4 addresses on the uplink interfaces 
+while Spoke devices receive addresses dynamically from a pre-defined DHCP 
+pool configured on ISP router. For redundancy purposes, we use 1 tunnel 
+interface on each Hub device and 2 tunnel interfaces on Spoke devices 
+destined to each of the Hubs. For the optimal tunnel operation timers are 
+significantly decreased and set to the following values:
+
+**NHRP** tunnel holding time - 30 seconds
+
+**IKE DPD** enabled with "restart" action set, interval 3 and timeout 
+30 seconds
+
+**Note**: these values are used only for the lab demonstration and may not 
+suit exclusive production networks.
+
+- Hub-1:
+
+.. code-block:: none
+   
+    set interfaces tunnel tun100 address '172.16.253.134/29'
+    set interfaces tunnel tun100 encapsulation 'gre'
+    set interfaces tunnel tun100 multicast 'enable'
+    set interfaces tunnel tun100 parameters ip key '1'
+    set interfaces tunnel tun100 source-address '10.11.0.1'
+    
+    set protocols nhrp tunnel tun100 cisco-authentication 'secret'
+    set protocols nhrp tunnel tun100 holding-time '30'
+    set protocols nhrp tunnel tun100 multicast 'dynamic'
+    set protocols nhrp tunnel tun100 redirect
+    set protocols nhrp tunnel tun100 shortcut
+    
+    set vpn ipsec esp-group ESP-HUB compression 'disable'
+    set vpn ipsec esp-group ESP-HUB lifetime '1800'
+    set vpn ipsec esp-group ESP-HUB mode 'transport'
+    set vpn ipsec esp-group ESP-HUB pfs 'dh-group2'
+    set vpn ipsec esp-group ESP-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec esp-group ESP-HUB proposal 1 hash 'sha1'
+    set vpn ipsec esp-group ESP-HUB proposal 2 encryption '3des'
+    set vpn ipsec esp-group ESP-HUB proposal 2 hash 'md5'
+    set vpn ipsec ike-group IKE-HUB close-action 'none'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection action 'restart'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection interval '3'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection timeout '30'
+    set vpn ipsec ike-group IKE-HUB ikev2-reauth 'no'
+    set vpn ipsec ike-group IKE-HUB key-exchange 'ikev2'
+    set vpn ipsec ike-group IKE-HUB lifetime '3600'
+    set vpn ipsec ike-group IKE-HUB proposal 1 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec ike-group IKE-HUB proposal 1 hash 'sha1'
+    set vpn ipsec ike-group IKE-HUB proposal 2 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 2 encryption 'aes128'
+    set vpn ipsec ike-group IKE-HUB proposal 2 hash 'sha1'
+    set vpn ipsec ipsec-interfaces interface 'eth0'
+    set vpn ipsec profile NHRPVPN authentication mode 'pre-shared-secret'
+    set vpn ipsec profile NHRPVPN authentication pre-shared-secret 'secret'
+    set vpn ipsec profile NHRPVPN bind tunnel 'tun100'
+    set vpn ipsec profile NHRPVPN esp-group 'ESP-HUB'
+    set vpn ipsec profile NHRPVPN ike-group 'IKE-HUB'
+
+- Hub-2:
+
+.. code-block:: none
+   
+    set interfaces tunnel tun100 address '172.16.254.134/29'
+    set interfaces tunnel tun100 encapsulation 'gre'
+    set interfaces tunnel tun100 multicast 'enable'
+    set interfaces tunnel tun100 parameters ip key '2'
+    set interfaces tunnel tun100 source-address '10.21.0.1'
+    
+    set protocols nhrp tunnel tun100 cisco-authentication 'secret'
+    set protocols nhrp tunnel tun100 holding-time '30'
+    set protocols nhrp tunnel tun100 multicast 'dynamic'
+    set protocols nhrp tunnel tun100 redirect
+    set protocols nhrp tunnel tun100 shortcut
+    
+    set vpn ipsec esp-group ESP-HUB compression 'disable'
+    set vpn ipsec esp-group ESP-HUB lifetime '1800'
+    set vpn ipsec esp-group ESP-HUB mode 'transport'
+    set vpn ipsec esp-group ESP-HUB pfs 'dh-group2'
+    set vpn ipsec esp-group ESP-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec esp-group ESP-HUB proposal 1 hash 'sha1'
+    set vpn ipsec esp-group ESP-HUB proposal 2 encryption '3des'
+    set vpn ipsec esp-group ESP-HUB proposal 2 hash 'md5'
+    set vpn ipsec ike-group IKE-HUB close-action 'none'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection action 'restart'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection interval '3'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection timeout '30'
+    set vpn ipsec ike-group IKE-HUB ikev2-reauth 'no'
+    set vpn ipsec ike-group IKE-HUB key-exchange 'ikev2'
+    set vpn ipsec ike-group IKE-HUB lifetime '3600'
+    set vpn ipsec ike-group IKE-HUB proposal 1 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec ike-group IKE-HUB proposal 1 hash 'sha1'
+    set vpn ipsec ike-group IKE-HUB proposal 2 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 2 encryption 'aes128'
+    set vpn ipsec ike-group IKE-HUB proposal 2 hash 'sha1'
+    set vpn ipsec ipsec-interfaces interface 'eth0'
+    set vpn ipsec profile NHRPVPN authentication mode 'pre-shared-secret'
+    set vpn ipsec profile NHRPVPN authentication pre-shared-secret 'secret'
+    set vpn ipsec profile NHRPVPN bind tunnel 'tun100'
+    set vpn ipsec profile NHRPVPN esp-group 'ESP-HUB'
+    set vpn ipsec profile NHRPVPN ike-group 'IKE-HUB'
+    
+- Spoke-1:
+
+.. code-block:: none
+   
+    set interfaces tunnel tun100 address '172.16.253.131/29'
+    set interfaces tunnel tun100 encapsulation 'gre'
+    set interfaces tunnel tun100 multicast 'enable'
+    set interfaces tunnel tun100 parameters ip key '1'
+    set interfaces tunnel tun100 source-address '0.0.0.0'
+    set interfaces tunnel tun200 address '172.16.254.131/29'
+    set interfaces tunnel tun200 encapsulation 'gre'
+    set interfaces tunnel tun200 multicast 'enable'
+    set interfaces tunnel tun200 parameters ip key '2'
+    set interfaces tunnel tun200 source-address '0.0.0.0'
+    
+    set protocols nhrp tunnel tun100 cisco-authentication 'secret'
+    set protocols nhrp tunnel tun100 holding-time '30'
+    set protocols nhrp tunnel tun100 map 172.16.253.134/29 nbma-address '10.11.0.1'
+    set protocols nhrp tunnel tun100 map 172.16.253.134/29 register
+    set protocols nhrp tunnel tun100 multicast 'nhs'
+    set protocols nhrp tunnel tun100 redirect
+    set protocols nhrp tunnel tun100 shortcut
+    set protocols nhrp tunnel tun200 cisco-authentication 'secret'
+    set protocols nhrp tunnel tun200 holding-time '30'
+    set protocols nhrp tunnel tun200 map 172.16.254.134/29 nbma-address '10.21.0.1'
+    set protocols nhrp tunnel tun200 map 172.16.254.134/29 register
+    set protocols nhrp tunnel tun200 multicast 'nhs'
+    set protocols nhrp tunnel tun200 redirect
+    set protocols nhrp tunnel tun200 shortcut
+    
+    set vpn ipsec esp-group ESP-HUB compression 'disable'
+    set vpn ipsec esp-group ESP-HUB lifetime '1800'
+    set vpn ipsec esp-group ESP-HUB mode 'transport'
+    set vpn ipsec esp-group ESP-HUB pfs 'dh-group2'
+    set vpn ipsec esp-group ESP-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec esp-group ESP-HUB proposal 1 hash 'sha1'
+    set vpn ipsec esp-group ESP-HUB proposal 2 encryption '3des'
+    set vpn ipsec esp-group ESP-HUB proposal 2 hash 'md5'
+    set vpn ipsec ike-group IKE-HUB close-action 'none'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection action 'restart'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection interval '3'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection timeout '30'
+    set vpn ipsec ike-group IKE-HUB ikev2-reauth 'no'
+    set vpn ipsec ike-group IKE-HUB key-exchange 'ikev2'
+    set vpn ipsec ike-group IKE-HUB lifetime '3600'
+    set vpn ipsec ike-group IKE-HUB proposal 1 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec ike-group IKE-HUB proposal 1 hash 'sha1'
+    set vpn ipsec ike-group IKE-HUB proposal 2 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 2 encryption 'aes128'
+    set vpn ipsec ike-group IKE-HUB proposal 2 hash 'sha1'
+    set vpn ipsec ipsec-interfaces interface 'eth0'
+    set vpn ipsec profile NHRPVPN authentication mode 'pre-shared-secret'
+    set vpn ipsec profile NHRPVPN authentication pre-shared-secret 'secret'
+    set vpn ipsec profile NHRPVPN bind tunnel 'tun100'
+    set vpn ipsec profile NHRPVPN bind tunnel 'tun200'
+    set vpn ipsec profile NHRPVPN esp-group 'ESP-HUB'
+    set vpn ipsec profile NHRPVPN ike-group 'IKE-HUB'
+    
+- Spoke-2:
+
+.. code-block:: none
+   
+    set interfaces tunnel tun100 address '172.16.253.132/29'
+    set interfaces tunnel tun100 encapsulation 'gre'
+    set interfaces tunnel tun100 multicast 'enable'
+    set interfaces tunnel tun100 parameters ip key '1'
+    set interfaces tunnel tun100 source-address '0.0.0.0'
+    set interfaces tunnel tun200 address '172.16.254.132/29'
+    set interfaces tunnel tun200 encapsulation 'gre'
+    set interfaces tunnel tun200 multicast 'enable'
+    set interfaces tunnel tun200 parameters ip key '2'
+    set interfaces tunnel tun200 source-address '0.0.0.0'
+    
+    set protocols nhrp tunnel tun100 cisco-authentication 'secret'
+    set protocols nhrp tunnel tun100 holding-time '30'
+    set protocols nhrp tunnel tun100 map 172.16.253.134/29 nbma-address '10.11.0.1'
+    set protocols nhrp tunnel tun100 map 172.16.253.134/29 register
+    set protocols nhrp tunnel tun100 multicast 'nhs'
+    set protocols nhrp tunnel tun100 redirect
+    set protocols nhrp tunnel tun100 shortcut
+    set protocols nhrp tunnel tun200 cisco-authentication 'secret'
+    set protocols nhrp tunnel tun200 holding-time '30'
+    set protocols nhrp tunnel tun200 map 172.16.254.134/29 nbma-address '10.21.0.1'
+    set protocols nhrp tunnel tun200 map 172.16.254.134/29 register
+    set protocols nhrp tunnel tun200 multicast 'nhs'
+    set protocols nhrp tunnel tun200 redirect
+    set protocols nhrp tunnel tun200 shortcut
+    
+    set vpn ipsec esp-group ESP-HUB compression 'disable'
+    set vpn ipsec esp-group ESP-HUB lifetime '1800'
+    set vpn ipsec esp-group ESP-HUB mode 'transport'
+    set vpn ipsec esp-group ESP-HUB pfs 'dh-group2'
+    set vpn ipsec esp-group ESP-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec esp-group ESP-HUB proposal 1 hash 'sha1'
+    set vpn ipsec esp-group ESP-HUB proposal 2 encryption '3des'
+    set vpn ipsec esp-group ESP-HUB proposal 2 hash 'md5'
+    set vpn ipsec ike-group IKE-HUB close-action 'none'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection action 'restart'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection interval '3'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection timeout '30'
+    set vpn ipsec ike-group IKE-HUB ikev2-reauth 'no'
+    set vpn ipsec ike-group IKE-HUB key-exchange 'ikev2'
+    set vpn ipsec ike-group IKE-HUB lifetime '3600'
+    set vpn ipsec ike-group IKE-HUB proposal 1 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec ike-group IKE-HUB proposal 1 hash 'sha1'
+    set vpn ipsec ike-group IKE-HUB proposal 2 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 2 encryption 'aes128'
+    set vpn ipsec ike-group IKE-HUB proposal 2 hash 'sha1'
+    set vpn ipsec ipsec-interfaces interface 'eth0'
+    set vpn ipsec profile NHRPVPN authentication mode 'pre-shared-secret'
+    set vpn ipsec profile NHRPVPN authentication pre-shared-secret 'secret'
+    set vpn ipsec profile NHRPVPN bind tunnel 'tun100'
+    set vpn ipsec profile NHRPVPN bind tunnel 'tun200'
+    set vpn ipsec profile NHRPVPN esp-group 'ESP-HUB'
+    set vpn ipsec profile NHRPVPN ike-group 'IKE-HUB'
+    
+- Spoke-3:
+
+.. code-block:: none
+   
+    set interfaces tunnel tun100 address '172.16.253.133/29'
+    set interfaces tunnel tun100 encapsulation 'gre'
+    set interfaces tunnel tun100 multicast 'enable'
+    set interfaces tunnel tun100 parameters ip key '1'
+    set interfaces tunnel tun100 source-address '0.0.0.0'
+    set interfaces tunnel tun200 address '172.16.254.133/29'
+    set interfaces tunnel tun200 encapsulation 'gre'
+    set interfaces tunnel tun200 multicast 'enable'
+    set interfaces tunnel tun200 parameters ip key '2'
+    set interfaces tunnel tun200 source-address '0.0.0.0'
+    
+    set protocols nhrp tunnel tun100 cisco-authentication 'secret'
+    set protocols nhrp tunnel tun100 holding-time '30'
+    set protocols nhrp tunnel tun100 map 172.16.253.134/29 nbma-address '10.11.0.1'
+    set protocols nhrp tunnel tun100 map 172.16.253.134/29 register
+    set protocols nhrp tunnel tun100 multicast 'nhs'
+    set protocols nhrp tunnel tun100 redirect
+    set protocols nhrp tunnel tun100 shortcut
+    set protocols nhrp tunnel tun200 cisco-authentication 'secret'
+    set protocols nhrp tunnel tun200 holding-time '30'
+    set protocols nhrp tunnel tun200 map 172.16.254.134/29 nbma-address '10.21.0.1'
+    set protocols nhrp tunnel tun200 map 172.16.254.134/29 register
+    set protocols nhrp tunnel tun200 multicast 'nhs'
+    set protocols nhrp tunnel tun200 redirect
+    set protocols nhrp tunnel tun200 shortcut
+    
+    set vpn ipsec esp-group ESP-HUB compression 'disable'
+    set vpn ipsec esp-group ESP-HUB lifetime '1800'
+    set vpn ipsec esp-group ESP-HUB mode 'transport'
+    set vpn ipsec esp-group ESP-HUB pfs 'dh-group2'
+    set vpn ipsec esp-group ESP-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec esp-group ESP-HUB proposal 1 hash 'sha1'
+    set vpn ipsec esp-group ESP-HUB proposal 2 encryption '3des'
+    set vpn ipsec esp-group ESP-HUB proposal 2 hash 'md5'
+    set vpn ipsec ike-group IKE-HUB close-action 'none'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection action 'restart'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection interval '3'
+    set vpn ipsec ike-group IKE-HUB dead-peer-detection timeout '30'
+    set vpn ipsec ike-group IKE-HUB ikev2-reauth 'no'
+    set vpn ipsec ike-group IKE-HUB key-exchange 'ikev2'
+    set vpn ipsec ike-group IKE-HUB lifetime '3600'
+    set vpn ipsec ike-group IKE-HUB proposal 1 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 1 encryption 'aes256'
+    set vpn ipsec ike-group IKE-HUB proposal 1 hash 'sha1'
+    set vpn ipsec ike-group IKE-HUB proposal 2 dh-group '2'
+    set vpn ipsec ike-group IKE-HUB proposal 2 encryption 'aes128'
+    set vpn ipsec ike-group IKE-HUB proposal 2 hash 'sha1'
+    set vpn ipsec ipsec-interfaces interface 'eth0'
+    set vpn ipsec profile NHRPVPN authentication mode 'pre-shared-secret'
+    set vpn ipsec profile NHRPVPN authentication pre-shared-secret 'secret'
+    set vpn ipsec profile NHRPVPN bind tunnel 'tun100'
+    set vpn ipsec profile NHRPVPN bind tunnel 'tun200'
+    set vpn ipsec profile NHRPVPN esp-group 'ESP-HUB'
+    set vpn ipsec profile NHRPVPN ike-group 'IKE-HUB'
+    
+
+
+Step-4: Enabling eBGP as a Dynamic Routing Protocol between Hubs and Spokes
+===========================================================================
+
+For the simplified and better network management we're using eBGP for routing 
+information exchange between devices. As we're using Active-Standby mode in 
+this example, Hub-2 is configured with AS-prepand as an export route-policy 
+and VRRP transition scripts are used for switching mastership based on the 
+current link/device state. Also, we use multihop BFD for faster eBGP failure 
+detection.
+
+Hub-1 and Hub-2 VRRP transition scripts:
+________________________________________
+
+* /config/scripts/vrrp-master.sh
+
+.. code-block:: none
+    
+    #!/bin/vbash
+
+    if [ $(id -gn) != vyattacfg ]; then
+        exec sg vyattacfg "$0 $*"
+    fi
+    
+    source /opt/vyatta/etc/functions/script-template
+    
+    configure
+    delete protocols bgp 65000 peer-group DMVPN address-family ipv4-unicast route-map export AS65000-PREP
+    commit
+    
+    exit
+
+
+* /config/scripts/vrrp-fail.sh
+
+.. code-block:: none
+    
+    #!/bin/vbash
+
+    if [ $(id -gn) != vyattacfg ]; then
+        exec sg vyattacfg "$0 $*"
+    fi
+    
+    source /opt/vyatta/etc/functions/script-template
+    
+    configure
+    set protocols bgp 65000 peer-group DMVPN address-family ipv4-unicast route-map export AS65000-PREP
+    commit
+    
+    exit
+
+
+**Note**: some parts of the script might be dependent on your network topology 
+and connectivity. Be careful before using it on your own devices.
+
+
+Hub devices configuration:
+__________________________
+
+- Hub-1:
+
+.. code-block:: none
+   
+    set high-availability vrrp group HQ transition-script backup '/config/scripts/vrrp-fail.sh'
+    set high-availability vrrp group HQ transition-script fault '/config/scripts/vrrp-fail.sh'
+    set high-availability vrrp group HQ transition-script master '/config/scripts/vrrp-master.sh'
+    set high-availability vrrp group HQ transition-script stop '/config/scripts/vrrp-fail.sh'
+    
+    set policy route-map AS65000-PREP rule 1 action 'permit'
+    set policy route-map AS65000-PREP rule 1 set as-path-prepend '65000 65000 65000'
+    
+    set protocols bfd peer 172.16.253.131 interval multiplier '3'
+    set protocols bfd peer 172.16.253.131 interval receive '300'
+    set protocols bfd peer 172.16.253.131 interval transmit '300'
+    set protocols bfd peer 172.16.253.131 multihop
+    set protocols bfd peer 172.16.253.131 source address '172.16.253.134'
+    set protocols bfd peer 172.16.253.132 interval multiplier '3'
+    set protocols bfd peer 172.16.253.132 interval receive '300'
+    set protocols bfd peer 172.16.253.132 interval transmit '300'
+    set protocols bfd peer 172.16.253.132 multihop
+    set protocols bfd peer 172.16.253.132 source address '172.16.253.134'
+    set protocols bfd peer 172.16.253.133 interval multiplier '3'
+    set protocols bfd peer 172.16.253.133 interval receive '300'
+    set protocols bfd peer 172.16.253.133 interval transmit '300'
+    set protocols bfd peer 172.16.253.133 multihop
+    set protocols bfd peer 172.16.253.133 source address '172.16.253.134'
+    
+    set protocols bgp 65000 address-family ipv4-unicast network 192.168.0.0/24
+    set protocols bgp 65000 neighbor 172.16.253.131 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.131 remote-as '65001'
+    set protocols bgp 65000 neighbor 172.16.253.132 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.132 remote-as '65002'
+    set protocols bgp 65000 neighbor 172.16.253.133 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.133 remote-as '65003'
+    set protocols bgp 65000 parameters log-neighbor-changes
+    set protocols bgp 65000 parameters network-import-check
+    set protocols bgp 65000 peer-group DMVPN bfd
+
+- Hub-2:
+
+.. code-block:: none
+   
+    set high-availability vrrp group HQ transition-script backup '/config/scripts/vrrp-fail.sh'
+    set high-availability vrrp group HQ transition-script fault '/config/scripts/vrrp-fail.sh'
+    set high-availability vrrp group HQ transition-script master '/config/scripts/vrrp-master.sh'
+    set high-availability vrrp group HQ transition-script stop '/config/scripts/vrrp-fail.sh'
+    
+    set policy route-map AS65000-PREP rule 1 action 'permit'
+    set policy route-map AS65000-PREP rule 1 set as-path-prepend '65000 65000 65000'
+    
+    set protocols bfd peer 172.16.254.131 interval multiplier '3'
+    set protocols bfd peer 172.16.254.131 interval receive '300'
+    set protocols bfd peer 172.16.254.131 interval transmit '300'
+    set protocols bfd peer 172.16.254.131 multihop
+    set protocols bfd peer 172.16.254.131 source address '172.16.254.134'
+    set protocols bfd peer 172.16.254.132 interval multiplier '3'
+    set protocols bfd peer 172.16.254.132 interval receive '300'
+    set protocols bfd peer 172.16.254.132 interval transmit '300'
+    set protocols bfd peer 172.16.254.132 multihop
+    set protocols bfd peer 172.16.254.132 source address '172.16.254.134'
+    set protocols bfd peer 172.16.254.133 interval multiplier '3'
+    set protocols bfd peer 172.16.254.133 interval receive '300'
+    set protocols bfd peer 172.16.254.133 interval transmit '300'
+    set protocols bfd peer 172.16.254.133 multihop
+    set protocols bfd peer 172.16.254.133 source address '172.16.254.134'
+    
+    set protocols bgp 65000 address-family ipv4-unicast network 192.168.0.0/24
+    set protocols bgp 65000 neighbor 172.16.254.131 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.131 remote-as '65001'
+    set protocols bgp 65000 neighbor 172.16.254.132 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.132 remote-as '65002'
+    set protocols bgp 65000 neighbor 172.16.254.133 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.133 remote-as '65003'
+    set protocols bgp 65000 parameters log-neighbor-changes
+    set protocols bgp 65000 parameters network-import-check
+    set protocols bgp 65000 peer-group DMVPN address-family ipv4-unicast route-map export 'AS65000-PREP'
+    set protocols bgp 65000 peer-group DMVPN bfd
+    
+Spoke devices configuration:
+____________________________
+
+- Spoke-1:
+
+.. code-block:: none
+   
+    set protocols bfd peer 172.16.253.134 interval multiplier '3'
+    set protocols bfd peer 172.16.253.134 interval receive '300'
+    set protocols bfd peer 172.16.253.134 interval transmit '300'
+    set protocols bfd peer 172.16.253.134 multihop
+    set protocols bfd peer 172.16.253.134 source address '172.16.253.131'
+    set protocols bfd peer 172.16.254.134 interval multiplier '3'
+    set protocols bfd peer 172.16.254.134 interval receive '300'
+    set protocols bfd peer 172.16.254.134 interval transmit '300'
+    set protocols bfd peer 172.16.254.134 multihop
+    set protocols bfd peer 172.16.254.134 source address '172.16.254.131'
+    
+    set protocols bgp 65001 address-family ipv4-unicast network 192.168.1.0/24
+    set protocols bgp 65001 neighbor 172.16.253.134 address-family ipv4-unicast
+    set protocols bgp 65001 neighbor 172.16.253.134 bfd
+    set protocols bgp 65001 neighbor 172.16.253.134 remote-as '65000'
+    set protocols bgp 65001 neighbor 172.16.254.134 address-family ipv4-unicast
+    set protocols bgp 65001 neighbor 172.16.254.134 bfd
+    set protocols bgp 65001 neighbor 172.16.254.134 remote-as '65000'
+    set protocols bgp 65001 parameters log-neighbor-changes
+    
+- Spoke-2:
+
+.. code-block:: none
+   
+    set protocols bfd peer 172.16.253.134 interval multiplier '3'
+    set protocols bfd peer 172.16.253.134 interval receive '300'
+    set protocols bfd peer 172.16.253.134 interval transmit '300'
+    set protocols bfd peer 172.16.253.134 multihop
+    set protocols bfd peer 172.16.253.134 source address '172.16.253.132'
+    set protocols bfd peer 172.16.254.134 interval multiplier '3'
+    set protocols bfd peer 172.16.254.134 interval receive '300'
+    set protocols bfd peer 172.16.254.134 interval transmit '300'
+    set protocols bfd peer 172.16.254.134 multihop
+    set protocols bfd peer 172.16.254.134 source address '172.16.254.132'
+    
+    set protocols bgp 65002 address-family ipv4-unicast network 192.168.2.0/24
+    set protocols bgp 65002 neighbor 172.16.253.134 address-family ipv4-unicast
+    set protocols bgp 65002 neighbor 172.16.253.134 bfd
+    set protocols bgp 65002 neighbor 172.16.253.134 remote-as '65000'
+    set protocols bgp 65002 neighbor 172.16.254.134 address-family ipv4-unicast
+    set protocols bgp 65002 neighbor 172.16.254.134 bfd
+    set protocols bgp 65002 neighbor 172.16.254.134 remote-as '65000'
+    set protocols bgp 65002 parameters log-neighbor-changes
+    
+- Spoke-3:
+
+.. code-block:: none
+   
+    set protocols bfd peer 172.16.253.134 interval multiplier '3'
+    set protocols bfd peer 172.16.253.134 interval receive '300'
+    set protocols bfd peer 172.16.253.134 interval transmit '300'
+    set protocols bfd peer 172.16.253.134 multihop
+    set protocols bfd peer 172.16.253.134 source address '172.16.253.133'
+    set protocols bfd peer 172.16.254.134 interval multiplier '3'
+    set protocols bfd peer 172.16.254.134 interval receive '300'
+    set protocols bfd peer 172.16.254.134 interval transmit '300'
+    set protocols bfd peer 172.16.254.134 multihop
+    set protocols bfd peer 172.16.254.134 source address '172.16.254.133'
+    
+    set protocols bgp 65003 address-family ipv4-unicast network 192.168.3.0/24
+    set protocols bgp 65003 neighbor 172.16.253.134 address-family ipv4-unicast
+    set protocols bgp 65003 neighbor 172.16.253.134 bfd
+    set protocols bgp 65003 neighbor 172.16.253.134 remote-as '65000'
+    set protocols bgp 65003 neighbor 172.16.254.134 address-family ipv4-unicast
+    set protocols bgp 65003 neighbor 172.16.254.134 bfd
+    set protocols bgp 65003 neighbor 172.16.254.134 remote-as '65000'
+    set protocols bgp 65003 parameters log-neighbor-changes
+    
+**Note**: In case if you're using VyOS version that has a VRRP transition 
+scripts issues after a device reboot, as a temporary solution you may add
+postconfig-bootup script that reloads **keepalived** process additionally after 
+the device booted.
+
+- Hub devices /config/scripts/vyos-postconfig-bootup.script:
+
+.. code-block:: none
+   
+    #!/bin/sh
+    # This script is executed at boot time after VyOS configuration is fully applied.
+    # Any modifications required to work around unfixed bugs
+    # or use services not available through the VyOS CLI system can be placed here.
+    
+    echo "Reloading VRRP process"
+    sudo systemctl restart keepalived.service
+    echo "VRRP process reload completed"
+
+
+
+Step-5: Verification
+====================
+
+Now, it's time to check that all protocols are working as expected and mastership 
+during the failover switches correctly between Hub devices.
+
+- Checking VRRP state between Hub-1 and Hub-2:
+
+.. code-block:: none
+   
+    vyos@Hub-1:~$ show vrrp
+    Name    Interface      VRID  State      Priority  Last Transition
+    ------  -----------  ------  -------  ----------  -----------------
+    HQ      eth1v1            1  MASTER          200  14s
+    
+    vyos@Hub-2:~$ show vrrp
+    Name    Interface      VRID  State      Priority  Last Transition
+    ------  -----------  ------  -------  ----------  -----------------
+    HQ      eth1v1            1  BACKUP          100  29s
+
+- Checking NHRP and eBGP sessions between Hub and Spoke devices:
+
+.. code-block:: none
+   
+    vyos@Hub-1:~$ show nhrp tunnel
+    Status: ok
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.253.135/32
+    Alias-Address: 172.16.253.134
+    Flags: up
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.253.134/32
+    Flags: up
+    
+    Interface: tun100
+    Type: dynamic
+    Protocol-Address: 172.16.253.131/32
+    NBMA-Address: 10.11.1.11
+    Flags: up
+    Expires-In: 0:23
+    
+    Interface: tun100
+    Type: dynamic
+    Protocol-Address: 172.16.253.133/32
+    NBMA-Address: 10.31.1.11
+    Flags: up
+    Expires-In: 0:22
+    
+    Interface: tun100
+    Type: dynamic
+    Protocol-Address: 172.16.253.132/32
+    NBMA-Address: 10.21.1.11
+    Flags: up
+    Expires-In: 0:21
+    
+    vyos@Hub-1:~$ show bgp summary
+    
+    IPv4 Unicast Summary:
+    BGP router identifier 192.168.0.1, local AS number 65000 vrf-id 0
+    BGP table version 20
+    RIB entries 7, using 1344 bytes of memory
+    Peers 3, using 64 KiB of memory
+    Peer groups 1, using 64 bytes of memory
+    
+    Neighbor        V         AS   MsgRcvd   MsgSent   TblVer  InQ OutQ  Up/Down State/PfxRcd   PfxSnt
+    172.16.253.131  4      65001     26519     26526        0    0    0 00:43:38            1        4
+    172.16.253.132  4      65002     26545     26540        0    0    0 00:46:36            1        4
+    172.16.253.133  4      65003     26528     26520        0    0    0 00:41:59            1        4
+    
+    Total number of neighbors 3
+    
+    
+    vyos@Hub-2:~$ show nhrp tunnel
+    Status: ok
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.254.135/32
+    Alias-Address: 172.16.254.134
+    Flags: up
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.254.134/32
+    Flags: up
+    
+    Interface: tun100
+    Type: dynamic
+    Protocol-Address: 172.16.254.132/32
+    NBMA-Address: 10.21.1.11
+    Flags: up
+    Expires-In: 0:28
+    
+    Interface: tun100
+    Type: dynamic
+    Protocol-Address: 172.16.254.131/32
+    NBMA-Address: 10.11.1.11
+    Flags: up
+    Expires-In: 0:21
+    
+    Interface: tun100
+    Type: dynamic
+    Protocol-Address: 172.16.254.133/32
+    NBMA-Address: 10.31.1.11
+    Flags: up
+    Expires-In: 0:20
+    
+    vyos@Hub-2:~$ show bgp summary
+    
+    IPv4 Unicast Summary:
+    BGP router identifier 192.168.0.2, local AS number 65000 vrf-id 0
+    BGP table version 14
+    RIB entries 7, using 1344 bytes of memory
+    Peers 3, using 64 KiB of memory
+    Peer groups 1, using 64 bytes of memory
+    
+    Neighbor        V         AS   MsgRcvd   MsgSent   TblVer  InQ OutQ  Up/Down State/PfxRcd   PfxSnt
+    172.16.254.131  4      65001     26516     26516        0    0    0 00:43:03            1        4
+    172.16.254.132  4      65002     26563     26562        0    0    0 00:48:27            1        4
+    172.16.254.133  4      65003     26518     26516        0    0    0 00:42:20            1        4
+    
+    Total number of neighbors 3
+    
+- Checking BFD sessions between Hub and Spoke devices:
+
+.. code-block:: none
+   
+    vyos@Hub-1:~$ show protocols bfd peers
+    Session count: 6
+    SessionId  LocalAddress                             PeerAddress                             Status
+    =========  ============                             ===========                             ======
+    3600626867 172.16.253.134                           172.16.253.133                          up
+    1123939978 172.16.253.134                           172.16.253.131                          up
+    374394280  172.16.253.134                           172.16.253.132                          up
+    1786735466 172.16.253.134                           172.16.253.132                          up
+    1440522544 172.16.253.134                           172.16.253.131                          up
+    1106910911 172.16.253.134                           172.16.253.133                          up
+    
+    
+    vyos@Hub-2:~$ show protocols bfd peers
+    Session count: 6
+    SessionId  LocalAddress                             PeerAddress                             Status
+    =========  ============                             ===========                             ======
+    2442966178 172.16.254.134                           172.16.254.133                          up
+    393258775  172.16.254.134                           172.16.254.131                          up
+    2990308682 172.16.254.134                           172.16.254.133                          up
+    2267910949 172.16.254.134                           172.16.254.132                          up
+    3542474595 172.16.254.134                           172.16.254.131                          up
+    4239538185 172.16.254.134                           172.16.254.132                          up
+
+- Checking routing information and connectivity between Hub and Spoke devices:
+
+.. code-block:: none
+   
+    vyos@Hub-1:~$ show ip bgp
+    BGP table version is 20, local router ID is 192.168.0.1, vrf id 0
+    Default local pref 100, local AS 65000
+    Status codes:  s suppressed, d damped, h history, * valid, > best, = multipath,
+                   i internal, r RIB-failure, S Stale, R Removed
+    Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
+    Origin codes:  i - IGP, e - EGP, ? - incomplete
+    
+       Network          Next Hop            Metric LocPrf Weight Path
+    *> 192.168.0.0/24   0.0.0.0                  0         32768 i
+    *> 192.168.1.0/24   172.16.253.131           0             0 65001 i
+    *> 192.168.2.0/24   172.16.253.132           0             0 65002 i
+    *> 192.168.3.0/24   172.16.253.133           0             0 65003 i
+    
+    Displayed  4 routes and 4 total paths
+
+
+    vyos@Hub-2:~$ show ip bgp
+    BGP table version is 14, local router ID is 192.168.0.2, vrf id 0
+    Default local pref 100, local AS 65000
+    Status codes:  s suppressed, d damped, h history, * valid, > best, = multipath,
+                   i internal, r RIB-failure, S Stale, R Removed
+    Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
+    Origin codes:  i - IGP, e - EGP, ? - incomplete
+    
+       Network          Next Hop            Metric LocPrf Weight Path
+    *> 192.168.0.0/24   0.0.0.0                  0         32768 i
+    *> 192.168.1.0/24   172.16.254.131           0             0 65001 i
+    *> 192.168.2.0/24   172.16.254.132           0             0 65002 i
+    *> 192.168.3.0/24   172.16.254.133           0             0 65003 i
+    
+    Displayed  4 routes and 4 total paths
+
+
+    vyos@Spoke-1:~$ show ip bgp
+    BGP table version is 19, local router ID is 192.168.1.1, vrf id 0
+    Default local pref 100, local AS 65001
+    Status codes:  s suppressed, d damped, h history, * valid, > best, = multipath,
+                   i internal, r RIB-failure, S Stale, R Removed
+    Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self
+    Origin codes:  i - IGP, e - EGP, ? - incomplete
+    
+       Network          Next Hop            Metric LocPrf Weight Path
+    *  192.168.0.0/24   172.16.254.134           0             0 65000 65000 65000 65000 i
+    *>                  172.16.253.134           0             0 65000 i
+    *> 192.168.1.0/24   0.0.0.0                  0         32768 i
+    *  192.168.2.0/24   172.16.254.132                         0 65000 65000 65000 65000 65002 i
+    *>                  172.16.253.132                         0 65000 65002 i
+    *  192.168.3.0/24   172.16.254.133                         0 65000 65000 65000 65000 65003 i
+    *>                  172.16.253.133                         0 65000 65003 i
+    
+    Displayed  4 routes and 7 total paths
+
+As you can see, Hub-2 announces routes with longer(prepended) AS path as 
+we've configured it previously, those, traffic towards HQ subnet will be 
+forwarded over Hub-1 which is operating as an Active VRRP router. Let's 
+check connectivity and the path from Spoke-1 to the HQ local network:
+
+.. code-block:: none
+   
+    vyos@Spoke-1:~$ ping 192.168.0.10 count 5 interface 192.168.1.1
+    PING 192.168.0.10 (192.168.0.10) from 192.168.1.1 : 56(84) bytes of data.
+    64 bytes from 192.168.0.10: icmp_seq=1 ttl=63 time=3.50 ms
+    64 bytes from 192.168.0.10: icmp_seq=2 ttl=63 time=2.45 ms
+    64 bytes from 192.168.0.10: icmp_seq=3 ttl=63 time=2.34 ms
+    64 bytes from 192.168.0.10: icmp_seq=4 ttl=63 time=2.20 ms
+    64 bytes from 192.168.0.10: icmp_seq=5 ttl=63 time=2.44 ms
+    
+    --- 192.168.0.10 ping statistics ---
+    5 packets transmitted, 5 received, 0% packet loss, time 11ms
+    rtt min/avg/max/mdev = 2.195/2.583/3.496/0.465 ms
+    
+    vyos@Spoke-1:~$ traceroute 192.168.0.10
+    traceroute to 192.168.0.10 (192.168.0.10), 30 hops max, 60 byte packets
+     1  172.16.253.134 (172.16.253.134)  0.913 ms  0.884 ms  0.819 ms
+     2  192.168.0.10 (192.168.0.10)  1.352 ms  1.446 ms  1.391 ms
+
+From the output, we can confirm successful connectivity between Spoke-1 and HQ 
+local networks. From the traceroute we see that the traffic pass through the 
+Hub-1.
+
+Now, let's check traffic between Spoke sites. Based on our configuration, Spoke 
+sites are using shourtcut for direct reachability between each other. First, let's 
+check NHRP tunnels before passing the traffic between Spoke-1 and Spoke-2:
+
+.. code-block:: none
+   
+    vyos@Spoke-1:~$ show nhrp tunnel
+    Status: ok
+    
+    Interface: tun200
+    Type: local
+    Protocol-Address: 172.16.254.135/32
+    Alias-Address: 172.16.254.131
+    Flags: up
+    
+    Interface: tun200
+    Type: local
+    Protocol-Address: 172.16.254.131/32
+    Flags: up
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.253.135/32
+    Alias-Address: 172.16.253.131
+    Flags: up
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.253.131/32
+    Flags: up
+    
+    Interface: tun200
+    Type: static
+    Protocol-Address: 172.16.254.134/29
+    NBMA-Address: 10.21.0.1
+    Flags: used up
+    
+    Interface: tun100
+    Type: static
+    Protocol-Address: 172.16.253.134/29
+    NBMA-Address: 10.11.0.1
+    Flags: used up
+
+    vyos@Spoke-2:~$ show nhrp tunnel
+    Status: ok
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.253.135/32
+    Alias-Address: 172.16.253.132
+    Flags: up
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.253.132/32
+    Flags: up
+    
+    Interface: tun200
+    Type: local
+    Protocol-Address: 172.16.254.135/32
+    Alias-Address: 172.16.254.132
+    Flags: up
+    
+    Interface: tun200
+    Type: local
+    Protocol-Address: 172.16.254.132/32
+    Flags: up
+    
+    Interface: tun100
+    Type: static
+    Protocol-Address: 172.16.253.134/29
+    NBMA-Address: 10.11.0.1
+    Flags: used up
+    
+    Interface: tun200
+    Type: static
+    Protocol-Address: 172.16.254.134/29
+    NBMA-Address: 10.21.0.1
+
+
+After passing traffic we could see that there is additional shourtcut tunnel 
+created between Spoke-1 and Spoke-2 for the direct communication:
+
+.. code-block:: none
+   
+    vyos@Spoke-1:~$ ping 192.168.2.1 count 5 interface 192.168.1.1
+    PING 192.168.2.1 (192.168.2.1) from 192.168.1.1 : 56(84) bytes of data.
+    64 bytes from 192.168.2.1: icmp_seq=1 ttl=64 time=1.03 ms
+    64 bytes from 192.168.2.1: icmp_seq=2 ttl=64 time=0.820 ms
+    64 bytes from 192.168.2.1: icmp_seq=3 ttl=64 time=1.13 ms
+    64 bytes from 192.168.2.1: icmp_seq=4 ttl=63 time=1.41 ms
+    64 bytes from 192.168.2.1: icmp_seq=5 ttl=64 time=0.988 ms
+    
+    --- 192.168.2.1 ping statistics ---
+    5 packets transmitted, 5 received, 0% packet loss, time 10ms
+    rtt min/avg/max/mdev = 0.820/1.075/1.412/0.197 ms
+    
+    vyos@Spoke-1:~$ traceroute 192.168.2.1
+    traceroute to 192.168.2.1 (192.168.2.1), 30 hops max, 60 byte packets
+     1  192.168.2.1 (192.168.2.1)  1.172 ms  1.109 ms  1.151 ms
+
+    vyos@Spoke-1:~$ show nhrp tunnel
+    Status: ok
+    
+    Interface: tun200
+    Type: local
+    Protocol-Address: 172.16.254.135/32
+    Alias-Address: 172.16.254.131
+    Flags: up
+    
+    Interface: tun200
+    Type: local
+    Protocol-Address: 172.16.254.131/32
+    Flags: up
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.253.135/32
+    Alias-Address: 172.16.253.131
+    Flags: up
+    
+    Interface: tun100
+    Type: local
+    Protocol-Address: 172.16.253.131/32
+    Flags: up
+    
+    Interface: tun200
+    Type: static
+    Protocol-Address: 172.16.254.134/29
+    NBMA-Address: 10.21.0.1
+    Flags: used up
+    
+    ____________________________________
+    Interface: tun100
+    Type: cached
+    Protocol-Address: 172.16.253.132/32
+    NBMA-Address: 10.21.1.11
+    Flags: used up
+    Expires-In: 0:24
+    ____________________________________
+    
+    Interface: tun100
+    Type: static
+    Protocol-Address: 172.16.253.134/29
+    NBMA-Address: 10.11.0.1
+    Flags: used up
+
+The same applies to the rest of the devices and works with the same logic. 
+As we've already confirmed successfull connectivity between Hub and Spoke 
+devices, let's check failover process.
+
+- Failover on the health-check failure on Hub-1:
+  
+.. code-block:: none
+   
+    # disabling interface towards Hub-1 on ISP router
+    vyos@ISP1:~$ configure
+    [edit]
+    vyos@ISP1# set interfaces ethernet eth0 disable
+    [edit]
+    vyos@ISP1# commit
+    [edit]
+    vyos@ISP1#
+
+
+    # checking VRRP state and eBGP configuration on Hub-1:
+    vyos@Hub-1:~$ show vrrp
+    Name    Interface      VRID  State      Priority  Last Transition
+    ------  -----------  ------  -------  ----------  -----------------
+    HQ      eth1v1            1  FAULT           200  1m15s
+    
+    vyos@Hub-1:~$ show configuration commands | match bgp
+    set protocols bgp 65000 address-family ipv4-unicast network 192.168.0.0/24
+    set protocols bgp 65000 neighbor 172.16.253.131 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.131 remote-as '65001'
+    set protocols bgp 65000 neighbor 172.16.253.132 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.132 remote-as '65002'
+    set protocols bgp 65000 neighbor 172.16.253.133 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.133 remote-as '65003'
+    set protocols bgp 65000 parameters log-neighbor-changes
+    set protocols bgp 65000 peer-group DMVPN address-family ipv4-unicast route-map export 'AS65000-PREP'
+    set protocols bgp 65000 peer-group DMVPN bfd
+
+
+    # consecutive pings check from Spoke-1 to the HQ local network during the failure
+    --- 192.168.0.10 ping statistics ---
+    223 packets transmitted, 219 received, 1.79372% packet loss, time 679ms
+    rtt min/avg/max/mdev = 0.918/2.191/2.957/0.364 ms
+    vyos@Spoke-1:~$
+
+
+    # consecutive pings check from Spoke-3 to the Spoke-2 local network during the failure
+    --- 192.168.2.1 ping statistics ---
+    265 packets transmitted, 265 received, 0% packet loss, time 690ms
+    rtt min/avg/max/mdev = 0.663/1.128/2.272/0.285 ms
+    vyos@Spoke-3:~$
+
+**Note**: After bringing ISP interface towards Hub-1 back to UP state, 
+VRRP state will remain unchanged due to "no-preempt" option enabled 
+under the VRRP configuration on the Hub-1 and Hub-2 and will be changed 
+only during link/device failure on Hub-2.
+    
+- Failover during Hub-2 device failure:
+
+.. code-block:: none
+   
+    # Checking VRRP state and eBGP configuration on Hub-2 before reboot
+    vyos@Hub-2:~$ show vrrp
+    Name    Interface      VRID  State      Priority  Last Transition
+    ------  -----------  ------  -------  ----------  -----------------
+    HQ      eth1v1            1  MASTER          100  20m22s
+
+    vyos@Hub-2:~$ show configuration commands | match bgp
+    set protocols bgp 65000 address-family ipv4-unicast network 192.168.0.0/24
+    set protocols bgp 65000 neighbor 172.16.254.131 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.131 remote-as '65001'
+    set protocols bgp 65000 neighbor 172.16.254.132 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.132 remote-as '65002'
+    set protocols bgp 65000 neighbor 172.16.254.133 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.133 remote-as '65003'
+    set protocols bgp 65000 parameters log-neighbor-changes
+    set protocols bgp 65000 peer-group DMVPN address-family ipv4-unicast route-map
+    set protocols bgp 65000 peer-group DMVPN bfd
+
+
+    # Rebooting Hub-2
+    vyos@Hub-2:~$ reboot
+    Are you sure you want to reboot this system? [y/N]  y
+
+    
+    # Checking VRRP state and eBGP configuration on Hub-1
+    vyos@Hub-1:~$ show vrrp
+    Name    Interface      VRID  State      Priority  Last Transition
+    ------  -----------  ------  -------  ----------  -----------------
+    HQ      eth1v1            1  MASTER          200  1m57s
+    
+    vyos@Hub-1:~$ show configuration commands | match bgp
+    set protocols bgp 65000 address-family ipv4-unicast network 192.168.0.0/24
+    set protocols bgp 65000 neighbor 172.16.253.131 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.131 remote-as '65001'
+    set protocols bgp 65000 neighbor 172.16.253.132 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.132 remote-as '65002'
+    set protocols bgp 65000 neighbor 172.16.253.133 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.253.133 remote-as '65003'
+    set protocols bgp 65000 parameters log-neighbor-changes
+    set protocols bgp 65000 peer-group DMVPN address-family ipv4-unicast route-map
+    set protocols bgp 65000 peer-group DMVPN bfd
+    
+    
+    # Checking VRRP state and eBGP configuration on Hub-2 after reboot completed
+    vyos@Hub-2:~$ show vrrp
+    Name    Interface      VRID  State      Priority  Last Transition
+    ------  -----------  ------  -------  ----------  -----------------
+    HQ      eth1v1            1  BACKUP          100  1m46s
+    
+    vyos@Hub-2:~$ show configuration commands | match bgp
+    set protocols bgp 65000 address-family ipv4-unicast network 192.168.0.0/24
+    set protocols bgp 65000 neighbor 172.16.254.131 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.131 remote-as '65001'
+    set protocols bgp 65000 neighbor 172.16.254.132 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.132 remote-as '65002'
+    set protocols bgp 65000 neighbor 172.16.254.133 peer-group 'DMVPN'
+    set protocols bgp 65000 neighbor 172.16.254.133 remote-as '65003'
+    set protocols bgp 65000 parameters log-neighbor-changes
+    set protocols bgp 65000 peer-group DMVPN address-family ipv4-unicast route-map export 'AS65000-PREP'
+    set protocols bgp 65000 peer-group DMVPN bfd
+
+
+    # consecutive pings check from Spoke-1 to the HQ local network during the failure
+    --- 192.168.0.10 ping statistics ---
+    1182 packets transmitted, 1182 received, 0% packet loss, time 1921ms
+    rtt min/avg/max/mdev = 0.890/1.692/3.305/0.503 ms
+    vyos@Spoke-1:~$
+
+
+    # consecutive pings check from Spoke-3 to the Spoke-2 local network during the failure
+    --- 192.168.2.1 ping statistics ---
+    1186 packets transmitted, 1186 received, 0% packet loss, time 2100ms
+    rtt min/avg/max/mdev = 0.506/1.236/8.497/0.369 ms
+    vyos@Spoke-3:~$
+
+From the results, we can see that the switchover performed as expected with 
+0 packets loss both from Spoke-1 to HQ and Spoke-3 to Spoke-2 networks.