VRRP(crux): addition of rfc3768-compatibility definition

Added the details of rfc3768-compatibility option and its command

1 files changed, 82 insertions, 25 deletions

diff --git a/docs/configuration/highavailability/index.rst b/docs/configuration/highavailability/index.rst
index 81cc2d44..457a78da 100644
--- a/docs/configuration/highavailability/index.rst
+++ b/docs/configuration/highavailability/index.rst
@@ -3,21 +3,29 @@
 High availability
 =================
 
-VRRP (Virtual Redundancy Protocol) provides active/backup redundancy for routers. 
-Every VRRP router has a physical IP/IPv6 address, and a virtual address.
-On startup, routers elect the master, and the router with the highest priority becomes the master and assigns the virtual address to its interface.
-All routers with lower priorities become backup routers. The master then starts sending keepalive packets to notify other routers that it's available.
-If the master fails and stops sending keepalive packets, the router with the next highest priority becomes the new master and takes over the virtual address.
-
-VRRP keepalive packets use multicast, and VRRP setups are limited to a single datalink layer segment.
-You can setup multiple VRRP groups (also called virtual routers). Virtual routers are identified by a VRID (Virtual Router IDentifier).
-If you setup multiple groups on the same interface, their VRIDs must be unique, but it's possible (even if not recommended for readability reasons) to use duplicate VRIDs on different interfaces.
+VRRP (Virtual Router Redundancy Protocol) provides active/backup redundancy for 
+routers. Every VRRP router has a physical IP/IPv6 address, and a virtual 
+address. On startup, routers elect the master, and the router with the highest 
+priority becomes the master and assigns the virtual address to its interface. 
+All routers with lower priorities become backup routers. The master then starts
+sending keepalive packets to notify other routers that it's available. If the 
+master fails and stops sending keepalive packets, the router with the next 
+highest priority becomes the new master and takes over the virtual address.
+
+VRRP keepalive packets use multicast, and VRRP setups are limited to a single 
+datalink layer segment. You can setup multiple VRRP groups 
+(also called virtual routers). Virtual routers are identified by a 
+VRID (Virtual Router IDentifier). If you setup multiple groups on the same 
+interface, their VRIDs must be unique, but it's possible (even if not 
+recommended for readability reasons) to use duplicate VRIDs on different 
+interfaces.
 
 Basic setup
 -----------
 
-VRRP groups are created with the ``set high-availability vrrp group $GROUP_NAME`` commands.
-The required parameters are interface, vrid, and virtual-address.
+VRRP groups are created with the 
+``set high-availability vrrp group $GROUP_NAME`` commands. The required 
+parameters are interface, vrid, and virtual-address.
 
 minimal config
 
@@ -27,7 +35,8 @@ minimal config
   set high-availability vrrp group Foo interface eth0
   set high-availability vrrp group Foo virtual-address 192.0.2.1/24
 
-You can verify your VRRP group status with the operational mode ``run show vrrp`` command:
+You can verify your VRRP group status with the operational mode 
+``run show vrrp`` command:
 
 .. code-block:: none
 
@@ -39,7 +48,9 @@ You can verify your VRRP group status with the operational mode ``run show vrrp`
 IPv6 support
 ------------
 
-The ``virtual-address`` parameter can be either an IPv4 or IPv6 address, but you cannot mix IPv4 and IPv6 in the same group, and will need to create groups with different VRIDs specially for IPv4 and IPv6.
+The ``virtual-address`` parameter can be either an IPv4 or IPv6 address, but you
+cannot mix IPv4 and IPv6 in the same group, and will need to create groups with 
+different VRIDs specially for IPv4 and IPv6.
 
 Disabling a VRRP group
 ----------------------
@@ -50,7 +61,9 @@ You can disable a VRRP group with ``disable`` option:
 
   set high-availability vrrp group Foo disable
 
-A disabled group will be removed from the VRRP process and your router will not participate in VRRP for that VRID. It will disappear from operational mode commands output, rather than enter the backup state.
+A disabled group will be removed from the VRRP process and your router will not
+participate in VRRP for that VRID. It will disappear from operational mode 
+commands output, rather than enter the backup state.
 
 Setting VRRP group priority
 ---------------------------
@@ -61,7 +74,8 @@ VRRP priority can be set with ``priority`` option:
 
   set high-availability vrrp group Foo priority 200
 
-The priority must be an integer number from 1 to 255. Higher priority value increases router's precedence in the master elections.
+The priority must be an integer number from 1 to 255. Higher priority value 
+increases router's precedence in the master elections.
 
 Sync groups
 -----------
@@ -98,21 +112,29 @@ In the following example, when VLAN9 transitions, VLAN20 will also transition:
     }
 
 
-.. warning:: All items in a sync group should be similarly configured.  If one VRRP group is set to a different premption delay or priority, it would result in an endless transition loop.
+.. warning:: All items in a sync group should be similarly configured. 
+   If one VRRP group is set to a different premption delay or priority, 
+   it would result in an endless transition loop.
 
 
 Preemption
 ----------
 
-VRRP can use two modes: preemptive and non-preemptive. In the preemptive mode, if a router with a higher priority fails and then comes back, routers with lower priority will give up their master status. In non-preemptive mode, the newly elected master will keep the master status and the virtual address indefinitely.
+VRRP can use two modes: preemptive and non-preemptive. In the preemptive mode, 
+if a router with a higher priority fails and then comes back, routers with lower
+priority will give up their master status. In non-preemptive mode, the newly 
+elected master will keep the master status and the virtual address indefinitely.
 
-By default VRRP uses preemption. You can disable it with the "no-preempt" option:
+By default VRRP uses preemption. You can disable it with the "no-preempt" 
+option:
 
 .. code-block:: none
 
   set high-availability vrrp group Foo no-preempt
 
-You can also configure the time interval for preemption with the "preempt-delay" option. For example, to set the higher priority router to take over in 180 seconds, use:
+You can also configure the time interval for preemption with the "preempt-delay"
+option. For example, to set the higher priority router to take over in 180 
+seconds, use:
 
 .. code-block:: none
 
@@ -121,23 +143,55 @@ You can also configure the time interval for preemption with the "preempt-delay"
 Unicast VRRP
 ------------
 
-By default VRRP uses multicast packets. If your network does not support multicast for whatever reason, you can make VRRP use unicast communication instead.
+By default VRRP uses multicast packets. If your network does not support 
+multicast for whatever reason, you can make VRRP use unicast communication 
+instead.
 
 .. code-block:: none
 
   set high-availability vrrp group Foo peer-address 192.0.2.10
   set high-availability vrrp group Foo hello-source-address 192.0.2.15
 
+rfc3768-compatibility
+---------------------
+
+RFC 3768 defines a virtual MAC address to each VRRP virtual router. 
+This virtual router MAC address will be used as the source in all periodic VRRP 
+messages sent by the active node. When the rfc3768-compatibilty option is set, 
+a new VRRP interface is created, to which the MAC address and the virtual IP 
+address is automatically assigned.
+
+.. code-block:: none
+
+   set high-availability vrrp group Foo rfc3768-compatibility
+
+Verification
+
+.. code-block:: none
+
+   $show interfaces ethernet eth0v10
+   eth0v10@eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue 
+   state UP group default qlen 1000
+   link/ether 00:00:5e:00:01:0a brd ff:ff:ff:ff:ff:ff
+   inet 172.25.0.247/16 scope global eth0v10
+   valid_lft forever preferred_lft forever
+
 Scripting
 ---------
 
-VRRP functionality can be extended with scripts. VyOS supports two kinds of scripts: health check scripts and transition scripts. Health check scripts execute custom checks in addition to the master router reachability.
-Transition scripts are executed when VRRP state changes from master to backup or fault and vice versa and can be used to enable or disable certain services, for example.
+VRRP functionality can be extended with scripts. VyOS supports two kinds of 
+scripts: health check scripts and transition scripts. Health check scripts 
+execute custom checks in addition to the master router reachability. Transition 
+scripts are executed when VRRP state changes from master to backup or fault and 
+vice versa and can be used to enable or disable certain services, for example.
 
 Health check scripts
 ^^^^^^^^^^^^^^^^^^^^
 
-This setup will make the VRRP process execute the ``/config/scripts/vrrp-check.sh script`` every 60 seconds, and transition the group to the fault state if it fails (i.e. exits with non-zero status) three times:
+This setup will make the VRRP process execute the 
+``/config/scripts/vrrp-check.sh script`` every 60 seconds, and transition the 
+group to the fault state if it fails (i.e. exits with non-zero status) three 
+times:
 
 .. code-block:: none
 
@@ -148,8 +202,11 @@ This setup will make the VRRP process execute the ``/config/scripts/vrrp-check.s
 Transition scripts
 ^^^^^^^^^^^^^^^^^^
 
-Transition scripts can help you implement various fixups, such as starting and stopping services, or even modifying the VyOS config on VRRP transition.
-This setup will make the VRRP process execute the ``/config/scripts/vrrp-fail.sh`` with argument ``Foo`` when VRRP fails, and the ``/config/scripts/vrrp-master.sh`` when the router becomes the master:
+Transition scripts can help you implement various fixups, such as starting 
+and stopping services, or even modifying the VyOS config on VRRP transition.
+This setup will make the VRRP process execute the 
+``/config/scripts/vrrp-fail.sh`` with argument ``Foo`` when VRRP fails, and 
+the ``/config/scripts/vrrp-master.sh`` when the router becomes the master:
 
 .. code-block:: none