multicast: add pim and igmp and append existing igmp-proxy

4 files changed, 246 insertions, 27 deletions

diff --git a/docs/_static/images/multicast-basic.png b/docs/_static/images/multicast-basic.png
new file mode 100644
index 00000000..3d4a3de3
--- /dev/null
+++ b/docs/_static/images/multicast-basic.png
diff --git a/docs/routing/igmp-proxy.rst b/docs/routing/igmp-proxy.rst
deleted file mode 100644
index f55323cc..00000000
--- a/docs/routing/igmp-proxy.rst
+++ /dev/null
@@ -1,26 +0,0 @@
-.. _igmp_proxy:
-
-IGMP Proxy
-==========
-
-Internet Group Management Protocol (IGMP)
-
-A IGMP Proxy to send IGMP host messages on behalf of a connected client.
-The configuration must define one upstream interface, and one or more downstream interfaces.
-If multicast traffic originates outside the upstream subnet, the "alt-subnet" option can be used in order to define legal multicast sources.
-
-simple example:
----------------
-
-Interface eth1 LAN is behind NAT. In order to subscribe 10.0.0.0/23 subnet multicast which is in eth0 WAN we need igmp-proxy.
-
-.. code-block:: none
-
-  # show protocols igmp-proxy 
-  interface eth0 {
-      alt-subnet 10.0.0.0/23
-      role upstream
-  }
-  interface eth1 {
-      role downstream
-  }
\ No newline at end of file
diff --git a/docs/routing/index.rst b/docs/routing/index.rst
index 1a1db43f..f14996d6 100644
--- a/docs/routing/index.rst
+++ b/docs/routing/index.rst
@@ -18,4 +18,4 @@ BGP).
    static
    mss-clamp
    routing-policy
-   igmp-proxy
+   multicast
diff --git a/docs/routing/multicast.rst b/docs/routing/multicast.rst
new file mode 100644
index 00000000..a19da01f
--- /dev/null
+++ b/docs/routing/multicast.rst
@@ -0,0 +1,245 @@
+.. _multicast:
+
+#########
+Multicast
+#########
+
+VyOS facilitates IP Multicast by supporting **PIM Sparse Mode**,
+**IGMP** and **IGMP-Proxy**.
+
+
+************
+PIM and IGMP
+************
+
+PIM (Protocol Independent Multicast) must be configured in every
+interface of every participating router. Every router must also have the
+location of the Rendevouz Point manually configured. Then,
+unidirectional shared trees rooted at the Rendevouz Point will
+automatically be built for multicast distribution. 
+
+Traffic from multicast sources will go to the Rendezvous Point, and
+receivers will pull it from a shared tree using IGMP (Internet Group
+Management Protocol).
+
+Multicast receivers will talk IGMP to their local router, so, besides
+having PIM configured in every router, IGMP must also be configured in
+any router where there could be a multicast receiver locally connected. 
+
+VyOS supports both IGMP version 2 and version 3 (which allows
+source-specific multicast).
+
+
+Example
+-------
+
+In the following example we can see a basic multicast setup:
+
+.. image:: /_static/images/multicast-basic.png
+   :width: 90%
+   :align: center
+   :alt: Network Topology Diagram
+
+
+
+**Router 1**
+
+.. code-block:: none
+
+   set interfaces ethernet eth2 address '172.16.0.2/24'
+   set interfaces ethernet eth1 address '100.64.0.1/24'
+   set protocols ospf area 0 network '172.16.0.0/24'
+   set protocols ospf area 0 network '100.64.0.0/24'
+   set protocols igmp interface eth1
+   set protocols pim interface eth1
+   set protocols pim interface eth2
+   set protocols pim rp address 172.16.255.1 group '224.0.0.0/4'
+   
+**Router 3**
+
+.. code-block:: none
+
+   set interfaces dummy dum0 address '172.16.255.1/24'
+   set interfaces ethernet eth0 address '172.16.0.1/24'
+   set interfaces ethernet eth1 address '172.16.1.1/24'
+   set protocols ospf area 0 network '172.16.0.0/24'
+   set protocols ospf area 0 network '172.16.255.0/24'
+   set protocols ospf area 0 network '172.16.1.0/24'
+   set protocols pim interface dum0
+   set protocols pim interface eth0
+   set protocols pim interface eth1
+   set protocols pim rp address 172.16.255.1 group '224.0.0.0/4'
+   
+**Router 2**
+
+.. code-block:: none
+
+   set interfaces ethernet eth1 address '10.0.0.1/24'
+   set interfaces ethernet eth2 address '172.16.1.2/24'
+   set protocols ospf area 0 network '10.0.0.0/24'
+   set protocols ospf area 0 network '172.16.1.0/24'
+   set protocols pim interface eth1
+   set protocols pim interface eth2
+   set protocols pim rp address 172.16.255.1 group '224.0.0.0/4'
+   
+
+
+
+
+Basic commands
+--------------
+
+These are the commands for a basic setup.
+
+.. cfgcmd:: set protocols pim interface <interface-name>
+
+   Use this command to enable PIM in the selected interface so that it
+   can communicate with PIM neighbors.
+
+
+.. cfgcmd:: set protocols pim rp address <address> group <multicast-address/mask-bits>
+
+   Use this comand to manually configure a Rendevouz Point for PIM so
+   that join messages can be sent there. Set the Rendevouz Point address
+   and the matching prefix of group ranges covered. These values must
+   be shared with every router participating in the PIM network.
+ 
+
+.. cfgcmd:: set protocols igmp interface eth1
+
+   Use this command to configure an interface with IGMP so that PIM can
+   receive IGMP reports and query on the selected interface. By defaul
+   IGMP version 3 will be used.
+
+
+
+Tuning commands
+---------------
+
+You can also tune multicast with the following commands.
+
+.. cfgcmd:: set protocols pim interface <interface> dr-priority <value>
+
+   Use this PIM command in the selected interface to set the priority
+   (1-4294967295) you want to influence in the election of a node to
+   become the Designated Router for a LAN segment. The default priority
+   is 1, set a  higher value to give the router more preference in the
+   DR election process.
+
+
+.. cfgcmd:: set protocols pim int <interface> hello <seconds>
+
+   Use this command to configure the PIM hello interval in seconds
+   (1-180) for the selected interface.
+
+
+.. cfgcmd:: set protocols pim rp keep-alive-timer <seconds>
+
+   Use this PIM command to modify the the time out value (31-60000
+   seconds) for an `(S,G) <https://tools.ietf.org/html/rfc7761#section-4.1>`_
+   flow. 31 seconds is chosen for a lower bound as some hardware
+   platforms cannot see data flowing in better than 30 second chunks.
+
+
+.. cfgcmd:: set protocols igmp interface <interface> join <multicast-address> source <IP-address>
+
+   Use this command to allow the selected interface join a multicast
+   group defining the multicast address you want to join and the source
+   IP address too.
+
+
+.. cfgcmd:: set protocols igmp interface <interface query-interval <seconds>
+
+   Use this command to configure in the selected interface the IGMP
+   host query interval (1-1800) in seconds that PIM will use.
+
+
+.. cfgcmd:: set protocols igmp interface <interface query-max-response-time <deciseconds>
+
+   Use this command to configure in the selected interface the IGMP
+   query response timeout value (10-250) in deciseconds. If a report is
+   not returned in the specified time, it will be asumed the `(S,G) or
+   (*,G) state <https://tools.ietf.org/html/rfc7761#section-4.1>`_ has
+   timed out.
+
+
+.. cfgcmd:: set protocols igmp interface <interface> version <version-number> 
+
+   Use this command to define in the selected interface whether you
+   choose IGMP version 2 or 3. The default value is 3.
+
+
+
+**********
+IGMP Proxy
+**********
+
+:abbr:`IGMP (Internet Group Management Protocol)` proxy sends IGMP host messages
+on behalf of a connected client. The configuration must define one, and only one
+upstream interface, and one or more downstream interfaces.
+
+Configuration
+=============
+
+.. cfgcmd:: set protocols igmp-proxy interface <interface> role <upstream | downstream>
+
+   * **upstream:** The upstream network interface is the outgoing interface
+     which is responsible for communicating to available multicast data sources.
+     There can only be one upstream interface.
+
+   * **downstream:** Downstream network interfaces are the distribution
+     interfaces to the destination networks, where multicast clients can join
+     groups and receive multicast data. One or more downstream interfaces must
+     be configured.
+
+.. cfgcmd:: set protocols igmp-proxy interface <interface> alt-subnet <network>
+
+   Defines alternate sources for multicasting and IGMP data. The network address
+   must be on the following format 'a.b.c.d/n'. By default the router will
+   accept data from sources on the same network as configured on an interface.
+   If the multicast source lies on a remote network, one must define from where
+   traffic should be accepted.
+
+   This is especially useful for the upstream interface, since the source for
+   multicast traffic is often from a remote location.
+
+   This option can be supplied multiple times.
+
+.. cfgcmd:: set protocols igmp-proxy disable-quickleave
+
+   Disables quickleave mode. In this mode the daemon will not send a Leave IGMP
+   message upstream as soon as it receives a Leave message for any downstream
+   interface. The daemon will not ask for Membership reports on the downstream
+   interfaces, and if a report is received the group is not joined again
+   upstream.
+
+   If it's vital that the daemon should act exactly as a real multicast client
+   on the upstream interface, this function should be enabled.
+
+   Enabling this function increases the risk of bandwidth saturation.
+
+.. cfgcmd:: set protocols igmp-proxy disable
+
+   Disable this service.
+
+Example
+-------
+
+Interface `eth1` LAN is behind NAT. In order to subscribe `10.0.0.0/23` subnet
+multicast which is in `eth0` WAN we need to configure igmp-proxy.
+
+.. code-block:: none
+
+  set protocols igmp-proxy interface eth0 role upstream
+  set protocols igmp-proxy interface eth0 alt-subnet 10.0.0.0/23
+  set protocols igmp-proxy interface eth1 role downstream
+
+Operation
+=========
+
+.. opcmd:: restart igmp-proxy
+
+   Restart the IGMP proxy process.
+
+
+