commandtree: remove as it's replaced by dynamic cmd-list

3 files changed, 0 insertions, 999 deletions

diff --git a/docs/appendix/commandtree/configmode.rst b/docs/appendix/commandtree/configmode.rst
deleted file mode 100644
index 049863b6..00000000
--- a/docs/appendix/commandtree/configmode.rst
+++ /dev/null
@@ -1,542 +0,0 @@
-.. _commandtree_configmode:
-
-Configuration mode
-------------------
-
-.. code-block:: none
-
-  confirm           Confirm prior commit-confirm
-  comment           Add comment to this configuration element
-  commit            Commit the current set of changes
-  commit-confirm    Commit the current set of changes with 'confirm' required
-  compare           Compare configuration revisions
-  copy              Copy a configuration element
-  delete            Delete a configuration element
-  discard           Discard uncommitted changes
-  edit              Edit a sub-element
-  exit              Exit from this configuration level
-  load              Load configuration from a file and replace running configuration
-  loadkey           Load user SSH key from a file
-  merge             Load configuration from a file and merge running configuration
-  rename            Rename a configuration element
-  rollback          Rollback to a prior config revision (requires reboot)
-  run               Run an operational-mode command
-  save              Save configuration to a file
-  set               Set the value of a parameter or create a new element
-  show              Show the configuration (default values may be suppressed)
-
-
-Confirm
-^^^^^^^
-
-The ``confirm`` command confirms the prior ``commit-confirm``.
-
-Comment
-^^^^^^^
-
-The ``comment`` commands allow you to insert a comment above the current configuration section.
-The command cannot be used at the top of the configuration hierarchy, only on subsections. Comments needs to be commited, just like other config changes.
-
-To add a comment to a section, while being already at the proper section level:
-
-.. code-block:: none
-
-  [edit <section>]
-  vyos@vyos# comment "Type Comment Here"
-
-To add a comment directly to a section, from the top or a higher section:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# comment <section> "Type Comment Here"
-
-To remove a comment, add a blank comment to overwrite:
-
-.. code-block:: none
-
-  [edit <section>]
-  vyos@vyos# comment ""
-
-Examples
-********
-
-To add a comment to the "interfaces" section:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# edit interfaces
-  [edit interfaces]
-  vyos@vyos# comment "Here is a comment"
-  [edit interfaces]
-  vyos@vyos# commit
-
-The comment would then appear like this:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# show
-   /* Here is a comment */
-    interfaces {
-        ethernet eth0 {
-    [...]
-
-
-An important thing to note is that since the comment is added on top of the section, it will not appear if the ``show <section>`` command is used. With the above example, the ``show interfaces`` command would return starting after the "interfaces {" line, hiding the comment:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# show interfaces
-   ethernet eth0 {
-  [...]
-
-
-To add a comment to the interfaces section from the top:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# comment interfaces "test"
-
-
-The comment can be added to any node that already exists, even if it's multiple levels lower:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# comment interfaces ethernet eth0 vif 222 address "Far down comment"
-
-
-Commit
-^^^^^^
-
-The ``commit`` command commits the proposed changes to the configuration file.
-Every changes done in the configuration session is only applied when the configuration is committed. To view the changes that will be applied, use the show command.
-To discard the changes without committing, use the ``discard`` command. The ``commit`` command doesn't save the configuration, you need to manually use the ``save`` command.
-
-The confirm keyword can be added, see ``commit-confirm``. A comment can be entered, it will appear in the commit log.
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# commit
-  Possible completions:
-    <Enter>       Commit working configuration
-    comment       Comment for commit log
-
-Commit-confirm
-^^^^^^^^^^^^^^
-
-The ``commit-confirm`` command commits the proposed changes to the configuration file and starts a timer.
-If the ``confirm`` command is not entered before the timer expiration, the configuration will be rolled back and VyOS will reboot.
-The default timer value is 10 minutes, but a custom value can be entered.
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# commit-confirm
-  Possible completions:
-    <Enter>       Commit, rollback/reboot in 10 minutes if no confirm
-    <N>           Commit, rollback/reboot in N minutes if no confirm
-    comment       Comment for commit log
-
-
-Compare
-^^^^^^^
-
-VyOS maintains backups of previous configurations. To compare configuration revisions in configuration mode, use the compare command:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# compare
-  Possible completions:
-    <Enter>	Compare working & active configurations
-    saved		Compare working & saved configurations
-    <N>		Compare working with revision N
-    <N> <M>	Compare revision N with M
-
-    Revisions:
-      0	2019-03-20 20:57:22 root by boot-config-loader
-      1	2019-03-15 20:00:04 root by boot-config-loader
-      2	2019-03-05 01:58:39 vyos by cli
-      3	2019-03-05 01:54:59 vyos by cli
-      4	2019-03-05 01:53:08 vyos by cli
-      5	2019-03-05 01:52:21 vyos by cli
-      6	2019-02-24 21:01:24 root by boot-config-loader
-      7	2019-02-21 22:00:12 vyos by cli
-      8	2019-02-21 21:56:49 vyos by cli
-
-
-Copy
-^^^^
-
-The ``copy`` command allows you to copy a configuration object.
-
-Copy the configuration entrys from a firewall name WAN rule 1 to rule 2.
-
-.. code-block:: none
-
-  [edit firewall name WAN]
-  vyos@vyos# show
-   rule 1 {
-       action accept
-       source {
-           address 10.1.0.0/24
-       }
-   }
-  [edit firewall name WAN]
-  vyos@vyos# copy rule 1 to rule 2
-  [edit firewall name WAN]
-  vyos@vyos# show
-   rule 1 {
-       action accept
-       source {
-           address 10.1.0.0/24
-       }
-   }
-  +rule 2 {
-  +    action accept
-  +    source {
-  +        address 10.1.0.0/24
-  +    }
-  +}
-
-Delete
-^^^^^^
-
-The ``delte`` command is to delete a configuration entry.
-
-This Example delete the hole ``service tftp-server`` section.
-
-.. code-block:: none
-
-  delete service tftp-server
-
-Discard
-^^^^^^^
-
-The ``discard`` command removes all pending configuration changes.
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# discard
-
-    Changes have been discarded
-
-Edit
-^^^^
-
-The ``edit`` command allows you to navigate down into the configuration tree.
-
-To avoid writing or pasting long paths,
-you can set the edit level to any node with the "edit" command,
-such as "edit firewall name Foo".
-Once you are at some level, you can use relative node paths,
-such as "set rule 10 action accept" in this case.
-
-To get back to an upper level, use the ``up`` command or use the ``top`` command to get back to the upper most level.
-The ``[edit]`` text displays where the user is located in the configuration tree.
-
-.. code-block:: none
-
-  vyos@vyos# edit firewall name Foo
-
-  [edit firewall name Foo]
-
-  vyos@vyos# set rule 10 protocol tcp
-
-  [edit firewall name Foo]
-
-  vyos@vyos# edit rule 10
-
-  [edit firewall name Foo rule 10]
-
-  vyos@vyos# set destination port 22
-
-  [edit firewall name Foo rule 10]
-
-  vyos@vyos# up
-
-  [edit firewall name Foo]
-
-  vyos@vyos# set rule 10 description "Allow SSH"
-
-  [edit firewall name Foo]
-
-  vyos@vyos# top
-
-  [edit]
-
-Exit
-^^^^
-
-The ``exit`` command exits the current configuration mode. If the current configuration level isn't the top-most, then the configuration level is put back to the top-most level.
-If the configuration level is at the top-most level, then it exits the configuration mode and returns to operational mode.
-The ``exit`` command cannot be used if uncommitted changes exists in the configuration file. To exit with uncommitted changes, you either need to use the ``exit discard`` command or you need to commit the changes before exiting.
-The ``exit`` command doesn't save the configuration, only the ``save`` command does. A warning will be given when exiting with unsaved changes. Using the ``exit`` command in operational mode will logout the session.
-
-
-Exiting from a configuration level:
-
-
-.. code-block:: none
-
-  [edit interfaces ethernet eth0]
-  vyos@vyos# exit
-
-Exiting from configuration mode:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# exit
-  exit
-  vyos@vyos:~$
-
-Exiting from operational mode:
-
-.. code-block:: none
-
-  vyos@vyos:~$ exit
-  logout
-
-Error message when trying to exit with uncommitted changes:
-
-.. code-block:: none
-
-  vyos@vyos# exit
-  Cannot exit: configuration modified.
-  Use 'exit discard' to discard the changes and exit.
-
-
-Warning message when exiting with unsaved changes:
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# exit
-  Warning: configuration changes have not been saved.
-
-Load
-^^^^
-
-The ``load`` command load a configuration from a local or remote file. You have to be use ``commit`` to make the change active
-
-.. code-block:: none
-
-  <Enter>				Load from system config file
-  <file>				Load from file on local machine
-  scp://<user>:<passwd>@<host>/<file>	Load from file on remote machine
-  sftp://<user>:<passwd>@<host>/<file>	Load from file on remote machine
-  ftp://<user>:<passwd>@<host>/<file>	Load from file on remote machine
-  http://<host>/<file>			Load from file on remote machine
-  https://<host>/<file>			Load from file on remote machine
-  tftp://<host>/<file>			Load from file on remote machine
-
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# load
-  Loading configuration from '/config/config.boot'...
-
-  Load complete.  Use 'commit' to make changes active.
-
-
-Loadkey
-^^^^^^^^
-
-Copies the content of a public key to the ~/.ssh/authorized_keys file.
-
-.. code-block:: none
-
-  loadkey <username> [tab]
-
-  <file>                      Load from file on local machine
-  scp://<user>@<host>/<file>  Load from file on remote machine
-  sftp://<user>@<host>/<file> Load from file on remote machine
-  ftp://<user>@<host>/<file>  Load from file on remote machine
-  http://<host>/<file>        Load from file on remote machine
-  tftp://<host>/<file>        Load from file on remote machine
-
-Merge
-^^^^^
-
-The ``merge`` command merge the config from a local or remote file with the running config.
-
-In the example below exist a ``default-firewall.config`` file with some common firewall rules you saved earlier.
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# show firewall
-  Configuration under specified path is empty
-  [edit]
-  vyos@vyos# merge default-firewall.config
-  Loading configuration from '/config/default-firewall.config'...
-
-  Merge complete.  Use 'commit' to make changes active.
-
-  vyos@vyos# show firewall
-  +all-ping enable
-  +broadcast-ping disable
-  +config-trap disable
-  +ipv6-receive-redirects disable
-  +ipv6-src-route disable
-  +ip-src-route disable
-  +log-martians enable
-  +name WAN {
-  +    default-action drop
-  +    rule 1 {
-  +        action accept
-  +        source {
-  +            address 10.1.0.0/24
-  +        }
-  +    }
-  +    rule 2 {
-  +        action accept
-  +        source {
-  +            address 10.1.0.0/24
-  +        }
-  ......
-
-
-Rename
-^^^^^^
-
-The ``rename`` command allows you to rename or move a configuration object.
-
-See here how to move the configuration entrys from vlanid 3 to 2
-
-.. code-block:: none
-
-  [edit interfaces ethernet eth1]
-  vyos@vyos# show
-   duplex auto
-   hw-id 00:53:22:81:c6:59
-   smp-affinity auto
-   speed auto
-   vif 3 {
-       address 10.4.4.4/32
-   }
-  [edit interfaces ethernet eth1]
-  vyos@vyos# rename vif 3 to vif 2
-  [edit interfaces ethernet eth1]
-  vyos@vyos# show
-   duplex auto
-   hw-id 00:53:22:81:c6:59
-   smp-affinity auto
-   speed auto
-  +vif 2 {
-  +    address 10.4.4.4/32
-  +}
-  -vif 3 {
-  -    address 10.4.4.4/32
-  -}
-  [edit interfaces ethernet eth1]
-
-
-Rollback
-^^^^^^^^
-
-You can ``rollback`` configuration using the rollback command, however this command will currently trigger a system reboot.
-Use the compare command to verify the configuration you want to rollback to.
-
-.. code-block:: none
-
-  vyos@vyos# compare 1
-  [edit system]
-  >host-name vyos-1
-  [edit]
-  vyos@vyos# rollback 1
-  Proceed with reboot? [confirm][y]
-
-  Broadcast message from root@vyos-1 (pts/0) (Tue Dec 17 21:07:45 2018):
-
-  The system is going down for reboot NOW!
-
-Run
-^^^
-
-The ``run`` command allows you to execute any operational mode commands without exiting the configuration session.
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# run show interfaces
-  Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
-  Interface        IP Address                        S/L  Description
-  ---------        ----------                        ---  -----------
-  eth0             10.1.1.1/24                        u/u
-
-
-Save
-^^^^
-
-The ``save`` command saves the current configuration to non-volatile storage. VyOS also supports saving and loading configuration remotely using SCP, FTP, or TFTP.
-
-.. code-block:: none
-
-  <Enter>				Save to system config file
-  <file>				Save to file on local machine
-  scp://<user>:<passwd>@<host>/<file>	Save to file on remote machine
-  sftp://<user>:<passwd>@<host>/<file>	Save to file on remote machine
-  ftp://<user>:<passwd>@<host>/<file>	Save to file on remote machine
-  tftp://<host>/<file>			Save to file on remote machine
-
-Set
-^^^
-
-The ``set`` command create all configuration entrys
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# set protocols static route 0.0.0.0/0 next-hop 192.168.1.1
-
-Show
-^^^^
-
-The ``show`` command in the configuration mode displays the configuration and show uncommitted changes.
-
-Show the hole config, the address and description of eth1 is moving to vlan 2 if you commit the changes.
-
-.. code-block:: none
-
-  [edit]
-  vyos@vyos# show
-   interfaces {
-       dummy dum0 {
-           address 10.3.3.3/24
-       }
-       ethernet eth0 {
-           address dhcp
-           duplex auto
-           hw-id 00:53:22:2b:c0:0b
-           smp-affinity auto
-           speed auto
-       }
-       ethernet eth1 {
-  -        address 10.1.1.1/32
-  -        description "MGMT Interface"
-           duplex auto
-           hw-id 00:53:22:81:c6:59
-           smp-affinity auto
-           speed auto
-  +        vif 2 {
-  +            address 10.1.1.1/32
-  +            description "MGMT Interface"
-  +        }
-       }
-       loopback lo {
-       }
-   }
-   service {
-       ssh {
-           port 22
-  ......
diff --git a/docs/appendix/commandtree/index.rst b/docs/appendix/commandtree/index.rst
deleted file mode 100644
index a35aab27..00000000
--- a/docs/appendix/commandtree/index.rst
+++ /dev/null
@@ -1,13 +0,0 @@
-.. _commandtree:
-
-Command tree
-============
-
-See full command tree in Operational mode and Configuration mode
-
-.. toctree::
-   :maxdepth: 2
-   :hidden:
-
-   operationmode
-   configmode
diff --git a/docs/appendix/commandtree/operationmode.rst b/docs/appendix/commandtree/operationmode.rst
deleted file mode 100644
index 8092f248..00000000
--- a/docs/appendix/commandtree/operationmode.rst
+++ /dev/null
@@ -1,444 +0,0 @@
-.. _commandtree_operationmode:
-
-Operational mode
-----------------
-
-Operational mode allows for commands to perform operational system tasks and view system and service status.
-After this is the first view after the login.
-Please see :ref:`cli` for navigation in the CLI
-
-
-.. code-block:: none
-
-
-  vyos@vyos:~$ [tab]
-  Possible completions:
-    add               Add an object to a service
-    clear             Clear system information
-    clone             Clone an object
-    configure         Enter configure mode
-    connect           Establish a connection
-    copy              Copy an object
-    delete            Delete an object
-    disconnect        Take down a connection
-    force             Force an operation
-    format            Format a device
-    generate          Generate an object
-    install           Install a new system
-    monitor           Monitor system information
-    ping              Send IPv4 or IPv6 ICMP (Internet Control Message Protocol) echo requests
-    poweroff          Poweroff the system
-    reboot            Reboot the system
-    release           Release specified variable
-    rename            Rename an object
-    renew             Renew specified variable
-    reset             Reset a service
-    restart           Restart a service
-    set               Set operational options
-    show              Show system information
-    telnet            Telnet to a node
-    traceroute        Track network path to node
-    update            Update data for a service
-
-
-Add
-^^^
-
-.. code-block:: none
-
- raid         Add a RAID set element
- system       Add an item to a system facility
-
-Clear
-^^^^^
-
-.. code-block:: none
-
-  console            Clear screen
-  firewall           Clear firewall statistics
-  flow-accounting    Clear flow accounting
-  interfaces         Clear interface information
-  ip                 Clear Internet Protocol (IP) statistics or status
-  ipv6               Clear Internet Protocol (IPv6) statistics or status
-  nat                Clear network address translation (NAT) tables
-  policy             Clear policy statistics
-
-
-Clone
-^^^^^
-The ``clone`` command allows you to clone a configuration from a system image to another one, or from the running config to another system image.
-To clone the running config to a system image:
-
-.. code-block:: none
-
-  clone system config <system-image> from running
-
-To clone from system image A to system image B:
-
-.. code-block:: none
-
-  clone system config <system-image-B> from <system-image-A>
-
-
-Configure
-^^^^^^^^^
-
-The ``configure`` command allows you to enter configuration mode.
-
-.. code-block:: none
-
-  vyos@vyos:~$ configure
-  [edit]
-  vyos@vyos#
-
-
-Connect
-^^^^^^^
-
-The ``connect`` command allows you to bring up a connection oriented interface, like a pppoe interface.
-
-.. code-block:: none
-
-  connect interface <interface>
-
-Copy
-^^^^
-
-The ``copy`` command allows you to copy a file to your running config or over images.
-
-It can look like this example:
-
-.. code-block:: none
-
-  vyos@vyos:~$  copy file [tab]
-  Possible completions:
-    http://<user>:<passwd>@<host>/<file>
-                  Copy files from specified source
-    scp://<user>:<passwd>@<host>/<file>
-    ftp://<user>:<passwd>@<host>/<file>
-    tftp://<host>/<file>
-    1.2.0://config/
-    1.2.0-rolling+201902251818://config/
-    1.2.0-rolling+201902201040://config/
-    1.2.0-rolling+201902080337://config/
-    1.2.0-H4://config/
-    running://config/
-
-
-To copy from file A to file B:
-
-.. code-block:: none
-
-  copy <file A> to <file B>
-
-
-Delete
-^^^^^^
-
-.. code-block:: none
-
-  conntrack     Delete Conntrack entries
-  file          Delete files in a particular image
-  log           Delete a log file
-  raid          Remove a RAID set element
-  system        Delete system objects
-
-
-Disconnect
-^^^^^^^^^^
-
-The ``disconnect`` command allows you to take down a connection oriented interface, like a pppoe interface.
-
-.. code-block:: none
-
-  disconnect interface <interface>
-
-Force
-^^^^^
-
-.. code-block:: none
-
-  arp           Send gratuitous ARP request or reply
-  cluster       Force a cluster state transition
-
-
-Format
-^^^^^^
-
-The ``format`` command allows you to format a disk the same way as another one.
-
-.. code-block:: none
-
-  format disk <target> like <source>
-
-Generate
-^^^^^^^^
-
-.. code-block:: none
-
-  openvpn       OpenVPN key generation tool
-  ssh-server-key
-                Regenerate the host SSH keys and restart the SSH server
-  tech-support  Generate tech-support archive
-  vpn           VPN key generation utility
-  wireguard     wireguard key generation utility
-
-Install
-^^^^^^^
-
-The ``install`` command allows you to install the system image on the disk.
-
-.. code-block:: none
-
-  install image
-
-
-Monitor
-^^^^^^^
-
-``monitor`` can be used to continually view what is happening on the router.
-
-.. code-block:: none
-
-  bandwidth     Monitor interface bandwidth in real time
-  bandwidth-test
-                Initiate or wait for bandwidth test
-  cluster       Monitor clustering service
-  command       Monitor an operational mode command (refreshes every 2 seconds)
-  conntrack-sync
-                Monitor conntrack-sync
-  content-inspection
-                Monitor Content-Inspection
-  dhcp          Monitor Dynamic Host Control Protocol (DHCP)
-  dns           Monitor a Domain Name Service (DNS) daemon
-  firewall      Monitor Firewall
-  https         Monitor the Secure Hypertext Transfer Protocol (HTTPS) service
-  lldp          Monitor Link Layer Discovery Protocol (LLDP) daemon
-  log           Monitor last lines of messages file
-  nat           Monitor network address translation (NAT)
-  openvpn       Monitor OpenVPN
-  protocol      Monitor routing protocols
-  snmp          Monitor Simple Network Management Protocol (SNMP) daemon
-  stop-all      Stop all current background monitoring processes
-  traceroute    Monitor the path to a destination in realtime
-  traffic       Monitor traffic dumps
-  vpn           Monitor VPN
-  vrrp          Monitor Virtual Router Redundancy Protocol (VRRP)
-  webproxy      Monitor Webproxy service
-
-
-Ping
-^^^^
-
-The ``ping`` command allows you to send an ICMP-EchoRequest packet and display the ICMP-EchoReply received.
-
-.. code-block:: none
-
-  <hostname>    Send Internet Control Message Protocol (ICMP) echo request
-  <x.x.x.x>
-  <h:h:h:h:h:h:h:h>
-
-
-Poweroff
-^^^^^^^^
-
-The ``poweroff`` command allows you to properly shut down the VyOS instance. Without any modifier, the command is executed immediately.
-
-.. code-block:: none
-
-  <Enter>       Execute the current command
-  at            Poweroff at a specific time
-  cancel        Cancel a pending poweroff
-  in            Poweroff in X minutes
-  now           Poweroff the system without confirmation
-
-Reboot
-^^^^^^
-The ``reboot`` command allows you to properly restart the VyOS instance. Without any modifier, the command is executed immediately.
-
-.. code-block:: none
-
-  <Enter>       Execute the current command
-  at            Poweroff at a specific time
-  cancel        Cancel a pending poweroff
-  in            Poweroff in X minutes
-  now           Poweroff the system without confirmation
-
-Release
-^^^^^^^
-
-The ``release`` command allows you to release a DHCP or DHCPv6 lease.
-
-.. code-block:: none
-
-  vyos@vyos:~$ release dhcp interface <int>
-  vyos@vyos:~$ release dhcpv6 interface <int>
-
-
-Rename
-^^^^^^
-
-The ``rename`` command allows you to rename a system image.
-
-.. code-block:: none
-
- rename system image <currentname> <newname>
-
-
-Renew
-^^^^^
-
-The ``renew`` command allows you to renew a DHCP or DHCPv6 lease.
-
-.. code-block:: none
-
-  vyos@vyos:~$ renew dhcp interface <int>
-  vyos@vyos:~$ renew dhcpv6 interface <int>
-
-Reset
-^^^^^
-
-.. code-block:: none
-
-  conntrack     Reset all currently tracked connections
-  conntrack-sync
-                Reset connection syncing parameters
-  dns           Reset a DNS service state
-  firewall      reset a firewall group
-  ip            Reset Internet Protocol (IP) parameters
-  ipv6          Reset Internet Protocol version 6 (IPv6) parameters
-  nhrp          Clear/Purge NHRP entries
-  openvpn       Reset OpenVPN
-  terminal      Reset terminal
-  vpn           Reset Virtual Private Network (VPN) information
-
-Restart
-^^^^^^^
-
-.. code-block:: none
-
-  cluster       Restart cluster node
-  conntrack-sync
-                Restart connection tracking synchronization service
-  dhcp          Restart DHCP processes
-  dhcpv6        Restart DHCPv6 processes
-  dns           Restart a DNS service
-  flow-accounting
-                Restart flow-accounting service
-  https         Restart https server
-  vpn           Restart IPsec VPN
-  vrrp          Restart the VRRP (Virtual Router Redundancy Protocol) process
-  wan-load-balance
-                Restart WAN load balancing
-  webproxy      Restart webproxy service
-
-Set
-^^^
-
-.. code-block:: none
-
-  <OPTION>      Bash builtin set command
-  console       Control console behaviors
-  date          Set system date and time
-  system        Set system operational parameters
-  terminal      Control terminal behaviors
-
-Show
-^^^^
-
-.. code-block:: none
-
-  arp           Show Address Resolution Protocol (ARP) information
-  bridge        Show bridging information
-  cluster       Show clustering information
-  configuration Show available saved configurations
-  conntrack     Show conntrack entries in the conntrack table
-  conntrack-sync
-                Show connection syncing information
-  date          Show system time and date
-  dhcp          Show DHCP (Dynamic Host Configuration Protocol) information
-  dhcpv6        Show DHCPv6 (IPv6 Dynamic Host Configuration Protocol) information
-  disk          Show status of disk device
-  dns           Show DNS information
-  file          Show files for a particular image
-  firewall      Show firewall information
-  flow-accounting
-                Show flow accounting statistics
-  hardware      Show system hardware details
-  history       show command history
-  host          Show host information
-  incoming      Show ethernet input-policy information
-  interfaces    Show network interface information
-  ip            Show IPv4 routing information
-  ipv6          Show IPv6 routing information
-  license       Show VyOS license information
-  lldp          Show lldp
-  log           Show contents of current master log file
-  login         Show current login credentials
-  monitoring    Show currently monitored services
-  nat           Show Network Address Translation (NAT) information
-  nhrp          Show NHRP info
-  ntp           Show peer status of NTP daemon
-  openvpn       Show OpenVPN information
-  policy        Show policy information
-  poweroff      Show scheduled poweroff
-  pppoe-server  show pppoe-server status
-  queueing      Show ethernet queueing information
-  raid          Show statis of RAID set
-  reboot        Show scheduled reboot
-  remote-config Show remote side config
-  route-map     Show route-map information
-  snmp          Show status of SNMP on localhost
-  system        Show system information
-  system-integrity
-                checks the integrity of the system
-  table         Show routing table
-  tech-support  Show consolidated tech-support report (private information removed)
-  users         Show user information
-  version       Show system version information
-  vpn           Show Virtual Private Network (VPN) information
-  vrrp          Show VRRP (Virtual Router Redundancy Protocol) information
-  wan-load-balance
-                Show Wide Area Network (WAN) load-balancing information
-  webproxy      Show webproxy information
-  wireguard     Show wireguard properties
-  zone-policy   Show summary of zone policy for a specific zone
-
-Telnet
-^^^^^^
-In the past the ``telnet`` command allowed you to connect remotely to another device using the telnet protocol.
-Telnet is unencrypted and should not use anymore. But its nice to test if an TCP Port to a host is open.
-
-
-.. code-block:: none
-
-  vyos@vyos:~$ telnet 192.168.1.3 443
-  Trying 192.168.1.3...
-  telnet: Unable to connect to remote host: Network is unreachable
-
-  vyos@vyos:~$ telnet 192.168.1.4 443
-  Trying 192.168.1.4...
-  Connected to 192.168.1.4.
-  Escape character is '^]'.
-
-Traceroute
-^^^^^^^^^^
-
-The ``traceroute`` command allows you to trace the path taken to a particular device.
-
-.. code-block:: none
-
-  <hostname>    Track network path to specified node
-  <x.x.x.x>
-  <h:h:h:h:h:h:h:h>
-  ipv4          Track network path to <hostname|IPv4 address>
-  ipv6          Track network path to <hostname|IPv6 address>
-
-
-Update
-^^^^^^
-
-.. code-block:: none
-
-  dns           Update DNS information
-  webproxy      Update webproxy
\ No newline at end of file