summaryrefslogtreecommitdiff
path: root/docs/appendix
diff options
context:
space:
mode:
authorrebortg <github@ghlr.de>2020-12-06 21:41:10 +0100
committerrebortg <github@ghlr.de>2020-12-06 21:41:10 +0100
commitce090a4ced7fccce3fdc70142e22fa0009fae12b (patch)
tree457f57457c190008eb23e822f8b168c003ff6cd5 /docs/appendix
parentb1cb71c71935ad6b0a7d9effe8f4dc4467de2175 (diff)
downloadvyos-documentation-ce090a4ced7fccce3fdc70142e22fa0009fae12b.tar.gz
vyos-documentation-ce090a4ced7fccce3fdc70142e22fa0009fae12b.zip
arrange examples
Diffstat (limited to 'docs/appendix')
-rw-r--r--docs/appendix/examples/azure-vpn-bgp.rst130
-rw-r--r--docs/appendix/examples/azure-vpn-dual-bgp.rst155
-rw-r--r--docs/appendix/examples/bgp-ipv6-unnumbered.rst172
-rw-r--r--docs/appendix/examples/dhcp-relay-through-gre-bridge.rst77
-rw-r--r--docs/appendix/examples/ha.rst580
-rw-r--r--docs/appendix/examples/index.rst19
-rw-r--r--docs/appendix/examples/ospf-unnumbered.rst118
-rw-r--r--docs/appendix/examples/tunnelbroker-ipv6.rst169
-rw-r--r--docs/appendix/examples/wan-load-balancing.rst170
-rw-r--r--docs/appendix/examples/zone-policy.rst415
10 files changed, 0 insertions, 2005 deletions
diff --git a/docs/appendix/examples/azure-vpn-bgp.rst b/docs/appendix/examples/azure-vpn-bgp.rst
deleted file mode 100644
index 176e0ae0..00000000
--- a/docs/appendix/examples/azure-vpn-bgp.rst
+++ /dev/null
@@ -1,130 +0,0 @@
-.. _examples-azure-vpn-bgp:
-
-Route-Based Site-to-Site VPN to Azure (BGP over IKEv2/IPsec)
-------------------------------------------------------------
-
-This guide shows an example of a route-based IKEv2 site-to-site VPN to
-Azure using VTI and BGP for dynamic routing updates.
-
-For redundant / active-active configurations see `Route-Based Redundant Site-to-Site VPN to Azure (BGP over IKEv2/IPsec) <https://docs.vyos.io/en/crux/appendix/examples/azure-vpn-dual-bgp.html>`_
-
-Prerequisites
-^^^^^^^^^^^^^
-
-- A pair of Azure VNet Gateways deployed in active-passive
- configuration with BGP enabled.
-
-- A local network gateway deployed in Azure representing
- the Vyos device, matching the below Vyos settings except for
- address space, which only requires the Vyos private IP, in
- this example 10.10.0.5/32
-
-- A connection resource deployed in Azure linking the
- Azure VNet gateway and the local network gateway representing
- the Vyos device.
-
-Example
-^^^^^^^
-
-+---------------------------------------+---------------------+
-| WAN Interface | eth0 |
-+---------------------------------------+---------------------+
-| On-premises address space | 10.10.0.0/16 |
-+---------------------------------------+---------------------+
-| Azure address space | 10.0.0.0/16 |
-+---------------------------------------+---------------------+
-| Vyos public IP | 198.51.100.3 |
-+---------------------------------------+---------------------+
-| Vyos private IP | 10.10.0.5 |
-+---------------------------------------+---------------------+
-| Azure VNet Gateway public IP | 203.0.113.2 |
-+---------------------------------------+---------------------+
-| Azure VNet Gateway BGP IP | 10.0.0.4 |
-+---------------------------------------+---------------------+
-| Pre-shared key | ch00s3-4-s3cur3-psk |
-+---------------------------------------+---------------------+
-| Vyos ASN | 64499 |
-+---------------------------------------+---------------------+
-| Azure ASN | 65540 |
-+---------------------------------------+---------------------+
-
-Vyos configuration
-^^^^^^^^^^^^^^^^^^
-
-- Configure the IKE and ESP settings to match a subset
- of those supported by Azure:
-
-.. code-block:: none
-
- set vpn ipsec esp-group AZURE compression 'disable'
- set vpn ipsec esp-group AZURE lifetime '3600'
- set vpn ipsec esp-group AZURE mode 'tunnel'
- set vpn ipsec esp-group AZURE pfs 'dh-group2'
- set vpn ipsec esp-group AZURE proposal 1 encryption 'aes256'
- set vpn ipsec esp-group AZURE proposal 1 hash 'sha1'
-
- set vpn ipsec ike-group AZURE dead-peer-detection action 'restart'
- set vpn ipsec ike-group AZURE dead-peer-detection interval '15'
- set vpn ipsec ike-group AZURE dead-peer-detection timeout '30'
- set vpn ipsec ike-group AZURE ikev2-reauth 'yes'
- set vpn ipsec ike-group AZURE key-exchange 'ikev2'
- set vpn ipsec ike-group AZURE lifetime '28800'
- set vpn ipsec ike-group AZURE proposal 1 dh-group '2'
- set vpn ipsec ike-group AZURE proposal 1 encryption 'aes256'
- set vpn ipsec ike-group AZURE proposal 1 hash 'sha1'
-
-- Enable IPsec on eth0
-
-.. code-block:: none
-
- set vpn ipsec ipsec-interfaces interface 'eth0'
-
-- Configure a VTI with a dummy IP address
-
-.. code-block:: none
-
- set interfaces vti vti1 address '10.10.1.5/32'
- set interfaces vti vti1 description 'Azure Tunnel'
-
-- Clamp the VTI's MSS to 1350 to avoid PMTU blackholes.
-
-.. code-block:: none
-
- set firewall options interface vti1 adjust-mss 1350
-
-- Configure the VPN tunnel
-
-.. code-block:: none
-
- set vpn ipsec site-to-site peer 203.0.113.2 authentication id '198.51.100.3'
- set vpn ipsec site-to-site peer 203.0.113.2 authentication mode 'pre-shared-secret'
- set vpn ipsec site-to-site peer 203.0.113.2 authentication pre-shared-secret 'ch00s3-4-s3cur3-psk'
- set vpn ipsec site-to-site peer 203.0.113.2 authentication remote-id '203.0.113.2'
- set vpn ipsec site-to-site peer 203.0.113.2 connection-type 'respond'
- set vpn ipsec site-to-site peer 203.0.113.2 description 'AZURE PRIMARY TUNNEL'
- set vpn ipsec site-to-site peer 203.0.113.2 ike-group 'AZURE'
- set vpn ipsec site-to-site peer 203.0.113.2 ikev2-reauth 'inherit'
- set vpn ipsec site-to-site peer 203.0.113.2 local-address '10.10.0.5'
- set vpn ipsec site-to-site peer 203.0.113.2 vti bind 'vti1'
- set vpn ipsec site-to-site peer 203.0.113.2 vti esp-group 'AZURE'
-
-- **Important**: Add an interface route to reach Azure's BGP listener
-
-.. code-block:: none
-
- set protocols static interface-route 10.0.0.4/32 next-hop-interface vti1
-
-- Configure your BGP settings
-
-.. code-block:: none
-
- set protocols bgp 64499 neighbor 10.0.0.4 remote-as '65540'
- set protocols bgp 64499 neighbor 10.0.0.4 address-family ipv4-unicast soft-reconfiguration 'inbound'
- set protocols bgp 64499 neighbor 10.0.0.4 timers holdtime '30'
- set protocols bgp 64499 neighbor 10.0.0.4 timers keepalive '10'
-
-- **Important**: Disable connected check \
-
-.. code-block:: none
-
- set protocols bgp 64499 neighbor 10.0.0.4 disable-connected-check
diff --git a/docs/appendix/examples/azure-vpn-dual-bgp.rst b/docs/appendix/examples/azure-vpn-dual-bgp.rst
deleted file mode 100644
index 13d4b5a2..00000000
--- a/docs/appendix/examples/azure-vpn-dual-bgp.rst
+++ /dev/null
@@ -1,155 +0,0 @@
-.. _examples-azure-vpn-dual-bgp:
-
-Route-Based Redundant Site-to-Site VPN to Azure (BGP over IKEv2/IPsec)
-----------------------------------------------------------------------
-
-This guide shows an example of a redundant (active-active) route-based IKEv2
-site-to-site VPN to Azure using VTI
-and BGP for dynamic routing updates.
-
-Prerequisites
-^^^^^^^^^^^^^
-
-- A pair of Azure VNet Gateways deployed in active-active
- configuration with BGP enabled.
-
-- A local network gateway deployed in Azure representing
- the Vyos device, matching the below Vyos settings except for
- address space, which only requires the Vyos private IP, in
- this example 10.10.0.5/32
-
-- A connection resource deployed in Azure linking the
- Azure VNet gateway and the local network gateway representing
- the Vyos device.
-
-Example
-^^^^^^^
-
-+---------------------------------------+---------------------+
-| WAN Interface | eth0 |
-+---------------------------------------+---------------------+
-| On-premises address space | 10.10.0.0/16 |
-+---------------------------------------+---------------------+
-| Azure address space | 10.0.0.0/16 |
-+---------------------------------------+---------------------+
-| Vyos public IP | 198.51.100.3 |
-+---------------------------------------+---------------------+
-| Vyos private IP | 10.10.0.5 |
-+---------------------------------------+---------------------+
-| Azure VNet Gateway 1 public IP | 203.0.113.2 |
-+---------------------------------------+---------------------+
-| Azure VNet Gateway 2 public IP | 203.0.113.3 |
-+---------------------------------------+---------------------+
-| Azure VNet Gateway BGP IP | 10.0.0.4,10.0.0.5 |
-+---------------------------------------+---------------------+
-| Pre-shared key | ch00s3-4-s3cur3-psk |
-+---------------------------------------+---------------------+
-| Vyos ASN | 64499 |
-+---------------------------------------+---------------------+
-| Azure ASN | 65540 |
-+---------------------------------------+---------------------+
-
-Vyos configuration
-^^^^^^^^^^^^^^^^^^
-
-- Configure the IKE and ESP settings to match a subset
- of those supported by Azure:
-
-.. code-block:: none
-
- set vpn ipsec esp-group AZURE compression 'disable'
- set vpn ipsec esp-group AZURE lifetime '3600'
- set vpn ipsec esp-group AZURE mode 'tunnel'
- set vpn ipsec esp-group AZURE pfs 'dh-group2'
- set vpn ipsec esp-group AZURE proposal 1 encryption 'aes256'
- set vpn ipsec esp-group AZURE proposal 1 hash 'sha1'
-
- set vpn ipsec ike-group AZURE dead-peer-detection action 'restart'
- set vpn ipsec ike-group AZURE dead-peer-detection interval '15'
- set vpn ipsec ike-group AZURE dead-peer-detection timeout '30'
- set vpn ipsec ike-group AZURE ikev2-reauth 'yes'
- set vpn ipsec ike-group AZURE key-exchange 'ikev2'
- set vpn ipsec ike-group AZURE lifetime '28800'
- set vpn ipsec ike-group AZURE proposal 1 dh-group '2'
- set vpn ipsec ike-group AZURE proposal 1 encryption 'aes256'
- set vpn ipsec ike-group AZURE proposal 1 hash 'sha1'
-
-- Enable IPsec on eth0
-
-.. code-block:: none
-
- set vpn ipsec ipsec-interfaces interface 'eth0'
-
-- Configure two VTIs with a dummy IP address each
-
-.. code-block:: none
-
- set interfaces vti vti1 address '10.10.1.5/32'
- set interfaces vti vti1 description 'Azure Primary Tunnel'
-
- set interfaces vti vti2 address '10.10.1.6/32'
- set interfaces vti vti2 description 'Azure Secondary Tunnel'
-
-- Clamp the VTI's MSS to 1350 to avoid PMTU blackholes.
-
-.. code-block:: none
-
- set firewall options interface vti1 adjust-mss 1350
- set firewall options interface vti2 adjust-mss 1350
-
-- Configure the VPN tunnels
-
-.. code-block:: none
-
- set vpn ipsec site-to-site peer 203.0.113.2 authentication id '198.51.100.3'
- set vpn ipsec site-to-site peer 203.0.113.2 authentication mode 'pre-shared-secret'
- set vpn ipsec site-to-site peer 203.0.113.2 authentication pre-shared-secret 'ch00s3-4-s3cur3-psk'
- set vpn ipsec site-to-site peer 203.0.113.2 authentication remote-id '203.0.113.2'
- set vpn ipsec site-to-site peer 203.0.113.2 connection-type 'respond'
- set vpn ipsec site-to-site peer 203.0.113.2 description 'AZURE PRIMARY TUNNEL'
- set vpn ipsec site-to-site peer 203.0.113.2 ike-group 'AZURE'
- set vpn ipsec site-to-site peer 203.0.113.2 ikev2-reauth 'inherit'
- set vpn ipsec site-to-site peer 203.0.113.2 local-address '10.10.0.5'
- set vpn ipsec site-to-site peer 203.0.113.2 vti bind 'vti1'
- set vpn ipsec site-to-site peer 203.0.113.2 vti esp-group 'AZURE'
-
- set vpn ipsec site-to-site peer 203.0.113.3 authentication id '198.51.100.3'
- set vpn ipsec site-to-site peer 203.0.113.3 authentication mode 'pre-shared-secret'
- set vpn ipsec site-to-site peer 203.0.113.3 authentication pre-shared-secret 'ch00s3-4-s3cur3-psk'
- set vpn ipsec site-to-site peer 203.0.113.3 authentication remote-id '203.0.113.3'
- set vpn ipsec site-to-site peer 203.0.113.3 connection-type 'respond'
- set vpn ipsec site-to-site peer 203.0.113.3 description 'AZURE SECONDARY TUNNEL'
- set vpn ipsec site-to-site peer 203.0.113.3 ike-group 'AZURE'
- set vpn ipsec site-to-site peer 203.0.113.3 ikev2-reauth 'inherit'
- set vpn ipsec site-to-site peer 203.0.113.3 local-address '10.10.0.5'
- set vpn ipsec site-to-site peer 203.0.113.3 vti bind 'vti2'
- set vpn ipsec site-to-site peer 203.0.113.3 vti esp-group 'AZURE'
-
-- **Important**: Add an interface route to reach both Azure's BGP listeners
-
-.. code-block:: none
-
- set protocols static interface-route 10.0.0.4/32 next-hop-interface vti1
- set protocols static interface-route 10.0.0.5/32 next-hop-interface vti2
-
-- Configure your BGP settings
-
-.. code-block:: none
-
- set protocols bgp 64499 neighbor 10.0.0.4 remote-as '65540'
- set protocols bgp 64499 neighbor 10.0.0.4 address-family ipv4-unicast soft-reconfiguration 'inbound'
- set protocols bgp 64499 neighbor 10.0.0.4 timers holdtime '30'
- set protocols bgp 64499 neighbor 10.0.0.4 timers keepalive '10'
-
- set protocols bgp 64499 neighbor 10.0.0.5 remote-as '65540'
- set protocols bgp 64499 neighbor 10.0.0.5 address-family ipv4-unicast soft-reconfiguration 'inbound'
- set protocols bgp 64499 neighbor 10.0.0.5 timers holdtime '30'
- set protocols bgp 64499 neighbor 10.0.0.5 timers keepalive '10'
-
-- **Important**: Disable connected check, otherwise the routes learned
- from Azure will not be imported into the routing table.
-
-.. code-block:: none
-
- set protocols bgp 64499 neighbor 10.0.0.4 disable-connected-check
- set protocols bgp 64499 neighbor 10.0.0.5 disable-connected-check
diff --git a/docs/appendix/examples/bgp-ipv6-unnumbered.rst b/docs/appendix/examples/bgp-ipv6-unnumbered.rst
deleted file mode 100644
index ccc1f69a..00000000
--- a/docs/appendix/examples/bgp-ipv6-unnumbered.rst
+++ /dev/null
@@ -1,172 +0,0 @@
-.. _examples-bgp-ipv6-unnumbered:
-
-#########################################
-BGP IPv6 unnumbered with extended nexthop
-#########################################
-
-General information can be found in the :ref:`bgp` chapter.
-
-Configuration
-=============
-
-- Router A:
-
-.. code-block:: none
-
- set protocols bgp 64496 address-family ipv4-unicast redistribute connected
- set protocols bgp 64496 address-family ipv6-unicast redistribute connected
- set protocols bgp 64496 neighbor eth1 interface v6only
- set protocols bgp 64496 neighbor eth1 interface v6only peer-group 'fabric'
- set protocols bgp 64496 neighbor eth2 interface v6only
- set protocols bgp 64496 neighbor eth2 interface v6only peer-group 'fabric'
- set protocols bgp 64496 parameters bestpath as-path multipath-relax
- set protocols bgp 64496 parameters bestpath compare-routerid
- set protocols bgp 64496 parameters default no-ipv4-unicast
- set protocols bgp 64496 parameters router-id '192.168.0.1'
- set protocols bgp 64496 peer-group fabric address-family ipv4-unicast
- set protocols bgp 64496 peer-group fabric address-family ipv6-unicast
- set protocols bgp 64496 peer-group fabric capability extended-nexthop
- set protocols bgp 64496 peer-group fabric remote-as 'external'
-
-- Router B:
-
-.. code-block:: none
-
- set protocols bgp 64499 address-family ipv4-unicast redistribute connected
- set protocols bgp 64499 address-family ipv6-unicast redistribute connected
- set protocols bgp 64499 neighbor eth1 interface v6only
- set protocols bgp 64499 neighbor eth1 interface v6only peer-group 'fabric'
- set protocols bgp 64499 neighbor eth2 interface v6only
- set protocols bgp 64499 neighbor eth2 interface v6only peer-group 'fabric'
- set protocols bgp 64499 parameters bestpath as-path multipath-relax
- set protocols bgp 64499 parameters bestpath compare-routerid
- set protocols bgp 64499 parameters default no-ipv4-unicast
- set protocols bgp 64499 parameters router-id '192.168.0.2'
- set protocols bgp 64499 peer-group fabric address-family ipv4-unicast
- set protocols bgp 64499 peer-group fabric address-family ipv6-unicast
- set protocols bgp 64499 peer-group fabric capability extended-nexthop
- set protocols bgp 64499 peer-group fabric remote-as 'external'
-
-Results
-=======
-
-- Router A:
-
-.. code-block:: none
-
- vyos@vyos:~$ show interfaces
- Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
- Interface IP Address S/L Description
- --------- ---------- --- -----------
- eth0 198.51.100.34/24 u/u
- eth1 - u/u
- eth2 - u/u
- lo 127.0.0.1/8 u/u
- 192.168.0.1/32
- ::1/128
-
-.. code-block:: none
-
- vyos@vyos:~$ show ip route
- Codes: K - kernel route, C - connected, S - static, R - RIP,
- O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
- T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
- F - PBR, f - OpenFabric,
- > - selected route, * - FIB route
-
- S>* 0.0.0.0/0 [210/0] via 198.51.100.34, eth0, 03:21:53
- C>* 198.51.100.0/24 is directly connected, eth0, 03:21:53
- C>* 192.168.0.1/32 is directly connected, lo, 03:21:56
- B>* 192.168.0.2/32 [20/0] via fe80::a00:27ff:fe3b:7ed2, eth2, 00:05:07
- * via fe80::a00:27ff:fe7b:4000, eth1, 00:05:07
-
-.. code-block:: none
-
- vyos@vyos:~$ ping 192.168.0.2
- PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data.
- 64 bytes from 192.168.0.2: icmp_seq=1 ttl=64 time=0.575 ms
- 64 bytes from 192.168.0.2: icmp_seq=2 ttl=64 time=0.628 ms
- 64 bytes from 192.168.0.2: icmp_seq=3 ttl=64 time=0.581 ms
- 64 bytes from 192.168.0.2: icmp_seq=4 ttl=64 time=0.682 ms
- 64 bytes from 192.168.0.2: icmp_seq=5 ttl=64 time=0.597 ms
-
- --- 192.168.0.2 ping statistics ---
- 5 packets transmitted, 5 received, 0% packet loss, time 4086ms
- rtt min/avg/max/mdev = 0.575/0.612/0.682/0.047 ms
-
-.. code-block:: none
-
- vyos@vyos:~$ show ip bgp summary
-
- IPv4 Unicast Summary:
- BGP router identifier 192.168.0.1, local AS number 65020 vrf-id 0
- BGP table version 4
- RIB entries 5, using 800 bytes of memory
- Peers 2, using 41 KiB of memory
- Peer groups 1, using 64 bytes of memory
-
- Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
- eth1 4 64499 13 13 0 0 0 00:05:33 2
- eth2 4 64499 13 14 0 0 0 00:05:29 2
-
- Total number of neighbors 2
-
-- Router B:
-
-.. code-block:: none
-
- vyos@vyos:~$ show interfaces
- Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
- Interface IP Address S/L Description
- --------- ---------- --- -----------
- eth0 198.51.100.33/24 u/u
- eth1 - u/u
- eth2 - u/u
- lo 127.0.0.1/8 u/u
- 192.168.0.2/32
- ::1/128
-
-.. code-block:: none
-
- vyos@vyos:~$ show ip route
- Codes: K - kernel route, C - connected, S - static, R - RIP,
- O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
- T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
- F - PBR, f - OpenFabric,
- > - selected route, * - FIB route
-
- S>* 0.0.0.0/0 [210/0] via 198.51.100.33, eth0, 00:44:08
- C>* 198.51.100.0/24 is directly connected, eth0, 00:44:09
- B>* 192.168.0.1/32 [20/0] via fe80::a00:27ff:fe2d:205d, eth1, 00:06:18
- * via fe80::a00:27ff:fe93:e142, eth2, 00:06:18
- C>* 192.168.0.2/32 is directly connected, lo, 00:44:11
-
-.. code-block:: none
-
- vyos@vyos:~$ ping 192.168.0.1
- PING 192.168.0.1 (192.168.0.1) 56(84) bytes of data.
- 64 bytes from 192.168.0.1: icmp_seq=1 ttl=64 time=0.427 ms
- 64 bytes from 192.168.0.1: icmp_seq=2 ttl=64 time=0.471 ms
- 64 bytes from 192.168.0.1: icmp_seq=3 ttl=64 time=0.782 ms
- 64 bytes from 192.168.0.1: icmp_seq=4 ttl=64 time=0.715 ms
-
- --- 192.168.0.1 ping statistics ---
- 4 packets transmitted, 4 received, 0% packet loss, time 3051ms
- rtt min/avg/max/mdev = 0.427/0.598/0.782/0.155 ms
-
-.. code-block:: none
-
- vyos@vyos:~$ show ip bgp summary
- IPv4 Unicast Summary:
- BGP router identifier 192.168.0.2, local AS number 65021 vrf-id 0
- BGP table version 4
- RIB entries 5, using 800 bytes of memory
- Peers 2, using 41 KiB of memory
- Peer groups 1, using 64 bytes of memory
-
- Neighbor V AS MsgRcvd MsgSent TblVer InQ OutQ Up/Down State/PfxRcd
- eth1 4 64496 14 14 0 0 0 00:06:40 2
- eth2 4 64496 14 14 0 0 0 00:06:37 2
-
- Total number of neighbors 2
-
diff --git a/docs/appendix/examples/dhcp-relay-through-gre-bridge.rst b/docs/appendix/examples/dhcp-relay-through-gre-bridge.rst
deleted file mode 100644
index f94eb67f..00000000
--- a/docs/appendix/examples/dhcp-relay-through-gre-bridge.rst
+++ /dev/null
@@ -1,77 +0,0 @@
-.. _examples-dhcp-relay-through-gre-bridge:
-
-
-DHCP Relay through GRE-Bridge
------------------------------
-
-Diagram
-^^^^^^^
-
-.. image:: /_static/images/dhcp-relay-through-gre-bridge.png
- :width: 80%
- :align: center
- :alt: Network Topology Diagram
-
-Configuration
-^^^^^^^^^^^^^
-
-DHCP Server
-"""""""""""
-
-.. code-block:: none
-
- set interfaces ethernet eth0 address '10.0.2.1/24'
- set interfaces loopback lo address '3.3.3.3/24'
- set interfaces tunnel tun100 address '172.16.0.2/30'
- set interfaces tunnel tun100 encapsulation 'gre-bridge'
- set interfaces tunnel tun100 local-ip '10.0.2.1'
- set interfaces tunnel tun100 remote-ip '192.168.0.1'
- set protocols ospf area 0 network '3.3.3.0/24'
- set protocols ospf area 0 network '10.0.2.0/24'
- set protocols ospf parameters router-id '3.3.3.3'
- set protocols static interface-route 10.0.1.2/32 next-hop-interface tun100
- set service dhcp-server shared-network-name asdf authoritative
- set service dhcp-server shared-network-name asdf subnet 3.3.3.0/24 range 0 start '3.3.3.30'
- set service dhcp-server shared-network-name asdf subnet 3.3.3.0/24 range 0 stop '3.3.3.40'
- set service dhcp-server shared-network-name asdf subnet 10.0.1.0/24 default-router '10.0.1.2'
- set service dhcp-server shared-network-name asdf subnet 10.0.1.0/24 range 0 start '10.0.1.200'
- set service dhcp-server shared-network-name asdf subnet 10.0.1.0/24 range 0 stop '10.0.1.210'
- set service dhcp-server shared-network-name asdf subnet 10.2.1.0/24 range 0 start '10.2.1.222'
- set service dhcp-server shared-network-name asdf subnet 10.2.1.0/24 range 0 stop '10.2.1.233'
- set service dhcp-server shared-network-name asdf subnet 172.16.0.0/30 range 0 start '172.16.0.1'
- set service dhcp-server shared-network-name asdf subnet 172.16.0.0/30 range 0 stop '172.16.0.2'
-
-
-In-Between Router
-"""""""""""""""""
-
-.. code-block:: none
-
- set interfaces ethernet eth0 address '192.168.0.2/24'
- set interfaces ethernet eth1 address '10.0.2.2/24'
- set protocols ospf area 0 network '192.168.0.0/24'
- set protocols ospf area 0 network '10.0.2.0/24'
- set protocols ospf parameters router-id '192.168.0.2'
-
-
-DHCP Relay
-""""""""""
-
-.. code-block:: none
-
- set interfaces ethernet eth0 address '10.0.1.2/24'
- set interfaces ethernet eth1 address '192.168.0.1/24'
- set interfaces loopback lo address '1.1.1.1'
- set interfaces tunnel tun100 address '172.16.0.1/30'
- set interfaces tunnel tun100 encapsulation 'gre-bridge'
- set interfaces tunnel tun100 local-ip '192.168.0.1'
- set interfaces tunnel tun100 remote-ip '10.0.2.1'
- set protocols ospf area 0 network '10.0.1.0/24'
- set protocols ospf area 0 network '192.168.0.0/24'
- set protocols ospf area 0 network '1.1.1.0/24'
- set protocols ospf parameters router-id '1.1.1.1'
- set protocols static interface-route 3.3.3.3/32 next-hop-interface tun100
- set service dhcp-relay interface 'eth0'
- set service dhcp-relay interface 'tun100'
- set service dhcp-relay server '3.3.3.3'
-
diff --git a/docs/appendix/examples/ha.rst b/docs/appendix/examples/ha.rst
deleted file mode 100644
index 702cb2b2..00000000
--- a/docs/appendix/examples/ha.rst
+++ /dev/null
@@ -1,580 +0,0 @@
-#############################
-High Availability Walkthrough
-#############################
-
-This document walks you through a complete HA setup of two VyOS machines. This
-design is based on a VM as the primary router, and a physical machine as a
-backup, using VRRP, BGP, OSPF and conntrack sharing.
-
-The aim of this document is to walk you through setting everything up so you
-and up at a point where you can reboot any machine and not lose more than a few
-seconds worth of connectivity.
-
-Design
-======
-
-This is based on a real life, in production design. One of the complex issues
-is ensuring you have redundant data INTO your network. We do this with a pair
-of Cisco Nexus switches, and using Virtual PortChannels that are spanned across
-them. This as an added bonus, also allows for complete switch failure without
-an outage. How you achieve this yourself is left as an exercise to the reader
-but our setup is documented here.
-
-Walkthrough suggestion
-----------------------
-
-The ``commit`` command is implied after every section. If you make an error,
-``commit`` will warn you and you can fix it before getting too far into things.
-Please ensure you commit early and commit often.
-
-If you are following through this document, it is strongly suggested you
-complete the entire document, ONLY doing the virtual router1 steps, and then
-come back and walk through it AGAIN on the backup hardware router.
-
-This ensures you don't go to fast, or miss a step. However, it will make your
-life easier to configure the fixed IP address and default route now on the
-hardware router.
-
-Example Network
----------------
-
-In this document, we have been allocated 203.0.113.0/24 by our upstream
-provider, which we are publishing on VLAN100.
-
-They want us to establish a BGP session to their routers on 192.0.2.11 and
-192.0.2.12 from our routers 192.0.2.21 and 192.0.2.22. They are AS 65550 and
-we are AS65551.
-
-Our routers are going to have a floating IP address of 203.0.113.1, and use
-.2 and .3 as their fixed IPs.
-
-We are going to use 10.200.201.0/24 for an 'internal' network on VLAN201.
-
-When traffic is originated from the 10.200.201.0/24 network, it will be
-masqueraded to 203.0.113.1
-
-For connection between sites, we are running a WireGuard link to two REMOTE
-routers, and using OSPF over those links to distribute routes. That remote
-site is expected to send traffic from anything in 10.201.0.0/16
-
-VLANs
------
-
-These are the vlans we wll be using:
-
-* 50: Upstream, using the 192.0.2.0/24 network allocated by them.
-* 100: 'Public' network, using our 203.0.113.0/24 network.
-* 201: 'Internal' network, using 10.200.201.0/24
-
-Hardware
---------
-
-* switch1 (Nexus 10gb Switch)
-* switch2 (Nexus 10gb Switch)
-* compute1 (VMware ESXi 6.5)
-* compute2 (VMware ESXi 6.5)
-* compute3 (VMware ESXi 6.5)
-* router2 (Random 1RU machine with 4 NICs)
-
-Note that router1 is a VM that runs on one of the compute nodes.
-
-Network Cabling
----------------
-
-* From Datacenter - This connects into port 1 on both switches, and is tagged
- as VLAN 50
-* Cisco VPC Crossconnect - Ports 39 and 40 bonded between each switch
-* Hardware Router - Port 8 of each switch
-* compute1 - Port 9 of each switch
-* compute2 - Port 10 of each switch
-* compute3 - Port 11 of each switch
-
-This is ignoring the extra Out-of-band management networking, which should be
-on totally different switches, and a different feed into the rack, and is out
-of scope of this.
-
-.. note:: Our implementation uses VMware's Distributed Port Groups, which allows
- VMware to use LACP. This is a part of the ENTERPRISE licence, and is not
- available on a Free licence. If you are implementing this and do not have
- access to DPGs, you should not use VMware, and use some other virtualization
- platform instead.
-
-
-Basic Setup (via console)
-=========================
-
-Create your router1 VM so it is able to withstand a VM Host failing, or a
-network link failing. Using VMware, this is achieved by enabling vSphere DRS,
-vSphere Availability, and creating a Distributed Port Group that uses LACP.
-
-Many other Hypervisors do this, and I'm hoping that this document will be
-expanded to document how to do this for others.
-
-Create an 'All VLANs' network group, that passes all trunked traffic through
-to the VM. Attach this network group to router1 as eth0.
-
-.. note:: VMware: You must DISABLE SECURITY on this Port group. Make sure that
- ``Promiscuous Mode``\ , ``MAC address changes`` and ``Forged transmits`` are
- enabled. All of these will be done as part of failover.
-
-Bonding on Hardware Router
---------------------------
-
-Create a LACP bond on the hardware router. We are assuming that eth0 and eth1
-are connected to port 8 on both switches, and that those ports are configured
-as a Port-Channel.
-
-.. code-block:: none
-
- set interfaces bonding bond0 description 'Switch Port-Channel'
- set interfaces bonding bond0 hash-policy 'layer2'
- set interfaces bonding bond0 member interface 'eth0'
- set interfaces bonding bond0 member interface 'eth1'
- set interfaces bonding bond0 mode '802.3ad'
-
-
-Assign external IP addresses
-----------------------------
-
-VLAN 100 and 201 will have floating IP addresses, but VLAN50 does not, as this
-is talking directly to upstream. Create our IP address on vlan50.
-
-For the hardware router, replace ``eth0`` with ``bond0``. As (almost) every
-command is identical, this will not be specified unless different things need
-to be performed on different hosts.
-
-.. code-block:: none
-
- set interfaces ethernet eth0 vif 50 address '192.0.2.21/24'
-
-In this case, the hardware router has a different IP, so it would be
-
-.. code-block:: none
-
- set interfaces ethernet bond0 vif 50 address '192.0.2.22/24'
-
-Add (temporary) default route
------------------------------
-
-It is assumed that the routers provided by upstream are capable of acting as a
-default router, add that as a static route.
-
-.. code-block:: none
-
- set protocols static route 0.0.0.0/0 next-hop 192.0.2.11
- commit
- save
-
-
-Enable SSH
-----------
-
-Enable SSH so you can now SSH into the routers, rather than using the console.
-
-.. code-block:: none
-
- set service ssh
- commit
- save
-
-At this point you should be able to SSH into both of them, and will no longer
-need access to the console (unless you break something!)
-
-
-VRRP Configuration
-==================
-
-We are setting up VRRP so that it does NOT fail back when a machine returns into
-service, and it prioritizes router1 over router2.
-
-Internal Network
-----------------
-
-This has a floating IP address of 10.200.201.1/24, using virtual router ID 201.
-The difference between them is the interface name, hello-source-address, and
-peer-address.
-
-**router1**
-
-.. code-block:: none
-
- set interfaces ethernet eth0 vif 201 address 10.200.201.2/24
- set high-availability vrrp group int hello-source-address '10.200.201.2'
- set high-availability vrrp group int interface 'eth0.201'
- set high-availability vrrp group int peer-address '10.200.201.3'
- set high-availability vrrp group int no-preempt
- set high-availability vrrp group int priority '200'
- set high-availability vrrp group int virtual-address '10.200.201.1/24'
- set high-availability vrrp group int vrid '201'
-
-
-**router2**
-
-.. code-block:: none
-
- set interfaces ethernet bond0 vif 201 address 10.200.201.3/24
- set high-availability vrrp group int hello-source-address '10.200.201.3'
- set high-availability vrrp group int interface 'bond0.201'
- set high-availability vrrp group int peer-address '10.200.201.2'
- set high-availability vrrp group int no-preempt
- set high-availability vrrp group int priority '100'
- set high-availability vrrp group int virtual-address '10.200.201.1/24'
- set high-availability vrrp group int vrid '201'
-
-
-Public Network
---------------
-
-This has a floating IP address of 203.0.113.1/24, using virtual router ID 113.
-The virtual router ID is just a random number between 1 and 254, and can be set
-to whatever you want. Best practices suggest you try to keep them unique
-enterprise-wide.
-
-**router1**
-
-.. code-block:: none
-
- set interfaces ethernet eth0 vif 100 address 203.0.113.2/24
- set high-availability vrrp group public hello-source-address '203.0.113.2'
- set high-availability vrrp group public interface 'eth0.100'
- set high-availability vrrp group public peer-address '203.0.113.3'
- set high-availability vrrp group public no-preempt
- set high-availability vrrp group public priority '200'
- set high-availability vrrp group public virtual-address '203.0.113.1/24'
- set high-availability vrrp group public vrid '113'
-
-**router2**
-
-.. code-block:: none
-
- set interfaces ethernet bond0 vif 100 address 203.0.113.3/24
- set high-availability vrrp group public hello-source-address '203.0.113.3'
- set high-availability vrrp group public interface 'bond0.100'
- set high-availability vrrp group public peer-address '203.0.113.2'
- set high-availability vrrp group public no-preempt
- set high-availability vrrp group public priority '100'
- set high-availability vrrp group public virtual-address '203.0.113.1/24'
- set high-availability vrrp group public vrid '113'
-
-
-Create VRRP sync-group
-----------------------
-
-The sync group is used to replicate connection tracking. It needs to be assigned
-to a random VRRP group, and we are creating a sync group called ``sync`` using
-the vrrp group ``int``.
-
-.. code-block:: none
-
- set high-availability vrrp sync-group sync member 'int'
-
-Testing
--------
-
-At this point, you should be able to see both IP addresses when you run
-``show interfaces``\ , and ``show vrrp`` should show both interfaces in MASTER
-state (and SLAVE state on router2).
-
-.. code-block:: none
-
- vyos@router1:~$ show vrrp
- Name Interface VRID State Last Transition
- -------- ----------- ------ ------- -----------------
- int eth0.201 201 MASTER 100s
- public eth0.100 113 MASTER 200s
- vyos@router1:~$
-
-
-You should be able to ping to and from all the IPs you have allocated.
-
-NAT and conntrack-sync
-======================
-
-Masquerade Traffic originating from 10.200.201.0/24 that is heading out the
-public interface.
-
-.. note:: We explicitly exclude the primary upstream network so that BGP or
- OSPF traffic doesn't accidentally get NAT'ed.
-
-.. code-block:: none
-
- set nat source rule 10 destination address '!192.0.2.0/24'
- set nat source rule 10 outbound-interface 'eth0.50'
- set nat source rule 10 source address '10.200.201.0/24'
- set nat source rule 10 translation address '203.0.113.1'
-
-
-Configure conntrack-sync and disable helpers
---------------------------------------------
-
-Most conntrack modules cause more problems than they're worth, especially in a
-complex network. Turn them off by default, and if you need to turn them on
-later, you can do so.
-
-.. code-block:: none
-
- set system conntrack modules ftp disable
- set system conntrack modules gre disable
- set system conntrack modules nfs disable
- set system conntrack modules pptp disable
- set system conntrack modules sip disable
- set system conntrack modules tftp disable
-
-Now enable replication between nodes. Replace eth0.201 with bond0.201 on the
-hardware router.
-
-.. code-block:: none
-
- set service conntrack-sync accept-protocol 'tcp,udp,icmp'
- set service conntrack-sync event-listen-queue-size '8'
- set service conntrack-sync failover-mechanism vrrp sync-group 'sync'
- set service conntrack-sync interface eth0.201
- set service conntrack-sync mcast-group '224.0.0.50'
- set service conntrack-sync sync-queue-size '8'
-
-Testing
--------
-
-The simplest way to test is to look at the connection tracking stats on the
-standby hardware router with the command ``show conntrack-sync statistics``.
-The numbers should be very close to the numbers on the primary router.
-
-When you have both routers up, you should be able to establish a connection
-from a NAT'ed machine out to the internet, reboot the active machine, and that
-connection should be preserved, and will not drop out.
-
-OSPF Over WireGuard
-===================
-
-Wireguard doesn't have the concept of an up or down link, due to its design.
-This complicates AND simplifies using it for network transport, as for reliable
-state detection you need to use SOMETHING to detect when the link is down.
-
-If you use a routing protocol itself, you solve two problems at once. This is
-only a basic example, and is provided as a starting point.
-
-Configure Wireguard
--------------------
-
-There is plenty of instructions and documentation on setting up Wireguard. The
-only important thing you need to remember is to only use one WireGuard
-interface per OSPF connection.
-
-We use small /30's from 10.254.60/24 for the point-to-point links.
-
-**router1**
-
-Replace the 203.0.113.3 with whatever the other router's IP address is.
-
-.. code-block:: none
-
- set interfaces wireguard wg01 address '10.254.60.1/30'
- set interfaces wireguard wg01 description 'router1-to-offsite1'
- set interfaces wireguard wg01 ip ospf authentication md5 key-id 1 md5-key 'i360KoCwUGZvPq7e'
- set interfaces wireguard wg01 ip ospf cost '11'
- set interfaces wireguard wg01 ip ospf dead-interval '5'
- set interfaces wireguard wg01 ip ospf hello-interval '1'
- set interfaces wireguard wg01 ip ospf network 'point-to-point'
- set interfaces wireguard wg01 ip ospf priority '1'
- set interfaces wireguard wg01 ip ospf retransmit-interval '5'
- set interfaces wireguard wg01 ip ospf transmit-delay '1'
- set interfaces wireguard wg01 peer OFFSITE1 allowed-ips '0.0.0.0/0'
- set interfaces wireguard wg01 peer OFFSITE1 endpoint '203.0.113.3:50001'
- set interfaces wireguard wg01 peer OFFSITE1 persistent-keepalive '15'
- set interfaces wireguard wg01 peer OFFSITE1 pubkey 'GEFMOWzAyau42/HwdwfXnrfHdIISQF8YHj35rOgSZ0o='
- set interfaces wireguard wg01 port '50001'
-
-
-**offsite1**
-
-This is connecting back to the STATIC IP of router1, not the floating.
-
-.. code-block:: none
-
- set interfaces wireguard wg01 address '10.254.60.2/30'
- set interfaces wireguard wg01 description 'offsite1-to-router1'
- set interfaces wireguard wg01 ip ospf authentication md5 key-id 1 md5-key 'i360KoCwUGZvPq7e'
- set interfaces wireguard wg01 ip ospf cost '11'
- set interfaces wireguard wg01 ip ospf dead-interval '5'
- set interfaces wireguard wg01 ip ospf hello-interval '1'
- set interfaces wireguard wg01 ip ospf network 'point-to-point'
- set interfaces wireguard wg01 ip ospf priority '1'
- set interfaces wireguard wg01 ip ospf retransmit-interval '5'
- set interfaces wireguard wg01 ip ospf transmit-delay '1'
- set interfaces wireguard wg01 peer ROUTER1 allowed-ips '0.0.0.0/0'
- set interfaces wireguard wg01 peer ROUTER1 endpoint '192.0.2.21:50001'
- set interfaces wireguard wg01 peer ROUTER1 persistent-keepalive '15'
- set interfaces wireguard wg01 peer ROUTER1 pubkey 'CKwMV3ZaLntMule2Kd3G7UyVBR7zE8/qoZgLb82EE2Q='
- set interfaces wireguard wg01 port '50001'
-
-Test WireGuard
---------------
-
-Make sure you can ping 10.254.60.1 and .2 from both routers.
-
-Create Export Filter
---------------------
-
-We only want to export the networks we know we should be exporting. Always
-whitelist your route filters, both importing and exporting. A good rule of
-thumb is **'If you are not the default router for a network, don't advertise
-it'**. This means we explicitly do not want to advertise the 192.0.2.0/24
-network (but do want to advertise 10.200.201.0 and 203.0.113.0, which we ARE
-the default route for). This filter is applied to ``redistribute connected``.
-If we WERE to advertise it, the remote machines would see 192.0.2.21 available
-via their default route, establish the connection, and then OSPF would say
-'192.0.2.0/24 is available via this tunnel', at which point the tunnel would
-break, OSPF would drop the routes, and then 192.0.2.0/24 would be reachable via
-default again. This is called 'flapping'.
-
-.. code-block:: none
-
- set policy access-list 150 description 'Outbound OSPF Redistribution'
- set policy access-list 150 rule 10 action 'permit'
- set policy access-list 150 rule 10 destination any
- set policy access-list 150 rule 10 source inverse-mask '0.0.0.255'
- set policy access-list 150 rule 10 source network '10.200.201.0'
- set policy access-list 150 rule 20 action 'permit'
- set policy access-list 150 rule 20 destination any
- set policy access-list 150 rule 20 source inverse-mask '0.0.0.255'
- set policy access-list 150 rule 20 source network '203.0.113.0'
- set policy access-list 150 rule 100 action 'deny'
- set policy access-list 150 rule 100 destination any
- set policy access-list 150 rule 100 source any
-
-
-Create Import Filter
---------------------
-
-We only want to import networks we know about. Our OSPF peer should only be
-advertising networks in the 10.201.0.0/16 range. Note that this is an INVERSE
-MATCH. You deny in access-list 100 to accept the route.
-
-.. code-block:: none
-
- set policy access-list 100 description 'Inbound OSPF Routes from Peers'
- set policy access-list 100 rule 10 action 'deny'
- set policy access-list 100 rule 10 destination any
- set policy access-list 100 rule 10 source inverse-mask '0.0.255.255'
- set policy access-list 100 rule 10 source network '10.201.0.0'
- set policy access-list 100 rule 100 action 'permit'
- set policy access-list 100 rule 100 destination any
- set policy access-list 100 rule 100 source any
- set policy route-map PUBOSPF rule 100 action 'deny'
- set policy route-map PUBOSPF rule 100 match ip address access-list '100'
- set policy route-map PUBOSPF rule 500 action 'permit'
-
-
-Enable OSPF
------------
-
-Every router **must** have a unique router-id.
-The 'reference-bandwidth' is used because when OSPF was originally designed,
-the idea of a link faster than 1gbit was unheard of, and it does not scale
-correctly.
-
-.. code-block:: none
-
- set protocols ospf area 0.0.0.0 authentication 'md5'
- set protocols ospf area 0.0.0.0 network '10.254.60.0/24'
- set protocols ospf auto-cost reference-bandwidth '10000'
- set protocols ospf log-adjacency-changes
- set protocols ospf parameters abr-type 'cisco'
- set protocols ospf parameters router-id '10.254.60.2'
- set protocols ospf route-map PUBOSPF
-
-
-Test OSPF
----------
-
-When you have enabled OSPF on both routers, you should be able to see each
-other with the command ``show ip ospf neighbour``. The state must be 'Full'
-or '2-Way', if it is not then there is a network connectivity issue between the
-hosts. This is often caused by NAT or MTU issues. You should not see any new
-routes (unless this is the second pass) in the output of ``show ip route``
-
-Advertise connected routes
-==========================
-
-As a reminder, only advertise routes that you are the default router for. This
-is why we are NOT announcing the 192.0.2.0/24 network, because if that was
-announced into OSPF, the other routers would try to connect to that network
-over a tunnel that connects to that network!
-
-.. code-block:: none
-
- set protocols ospf access-list 150 export 'connected'
- set protocols ospf redistribute connected
-
-
-You should now be able to see the advertised network on the other host.
-
-Duplicate configuration
------------------------
-
-At this pont you now need to create the X link between all four routers. Use a
-different /30 for each link.
-
-Priorities
-----------
-
-Set the cost on the secondary links to be 200. This means that they will not
-be used unless the primary links are down.
-
-.. code-block:: none
-
- set interfaces wireguard wg01 ip ospf cost '10'
- set interfaces wireguard wg02 ip ospf cost '200'
-
-
-This will be visible in 'show ip route'.
-
-BGP
-===
-
-BGP is an extremely complex network protocol. An example is provided here.
-
-.. note:: Router id's must be unique.
-
-**router1**
-
-
-The ``redistribute ospf`` command is there purely as an example of how this can
-be expanded. In this walkthrough, it will be filtered by BGPOUT rule 10000, as
-it is not 203.0.113.0/24.
-
-.. code-block:: none
-
- set policy prefix-list BGPOUT description 'BGP Export List'
- set policy prefix-list BGPOUT rule 10 action 'deny'
- set policy prefix-list BGPOUT rule 10 description 'Do not advertise short masks'
- set policy prefix-list BGPOUT rule 10 ge '25'
- set policy prefix-list BGPOUT rule 10 prefix '0.0.0.0/0'
- set policy prefix-list BGPOUT rule 100 action 'permit'
- set policy prefix-list BGPOUT rule 100 description 'Our network'
- set policy prefix-list BGPOUT rule 100 prefix '203.0.113.0/24'
- set policy prefix-list BGPOUT rule 10000 action 'deny'
- set policy prefix-list BGPOUT rule 10000 prefix '0.0.0.0/0'
- set policy route-map BGPOUT description 'BGP Export Filter'
- set policy route-map BGPOUT rule 10 action 'permit'
- set policy route-map BGPOUT rule 10 match ip address prefix-list 'BGPOUT'
- set policy route-map BGPOUT rule 10000 action 'deny'
- set policy route-map BGPPREPENDOUT description 'BGP Export Filter'
- set policy route-map BGPPREPENDOUT rule 10 action 'permit'
- set policy route-map BGPPREPENDOUT rule 10 set as-path-prepend '65551 65551 65551'
- set policy route-map BGPPREPENDOUT rule 10 match ip address prefix-list 'BGPOUT'
- set policy route-map BGPPREPENDOUT rule 10000 action 'deny'
- set protocols bgp 65551 address-family ipv4-unicast network 192.0.2.0/24
- set protocols bgp 65551 address-family ipv4-unicast redistribute connected metric '50'
- set protocols bgp 65551 address-family ipv4-unicast redistribute ospf metric '50'
- set protocols bgp 65551 neighbor 192.0.2.11 address-family ipv4-unicast route-map export 'BGPOUT'
- set protocols bgp 65551 neighbor 192.0.2.11 address-family ipv4-unicast soft-reconfiguration inbound
- set protocols bgp 65551 neighbor 192.0.2.11 remote-as '65550'
- set protocols bgp 65551 neighbor 192.0.2.11 update-source '192.0.2.21'
- set protocols bgp 65551 parameters router-id '192.0.2.21'
-
-
-**router2**
-
-This is identical, but you use the BGPPREPENDOUT route-map to advertise the
-route with a longer path.
diff --git a/docs/appendix/examples/index.rst b/docs/appendix/examples/index.rst
deleted file mode 100644
index b2f7bfde..00000000
--- a/docs/appendix/examples/index.rst
+++ /dev/null
@@ -1,19 +0,0 @@
-.. _examples:
-
-Configuration Blueprints
-========================
-
-This chapter contains various configuration examples:
-
-.. toctree::
- :maxdepth: 2
-
- dhcp-relay-through-gre-bridge
- zone-policy
- bgp-ipv6-unnumbered
- ospf-unnumbered
- azure-vpn-bgp
- azure-vpn-dual-bgp
- tunnelbroker-ipv6
- ha
- wan-load-balancing
diff --git a/docs/appendix/examples/ospf-unnumbered.rst b/docs/appendix/examples/ospf-unnumbered.rst
deleted file mode 100644
index 39f8f69a..00000000
--- a/docs/appendix/examples/ospf-unnumbered.rst
+++ /dev/null
@@ -1,118 +0,0 @@
-.. _examples-ospf-unnumbered:
-
-#########################
-OSPF unnumbered with ECMP
-#########################
-
-General infomration can be found in the :ref:`routing-ospf` chapter.
-
-Configuration
-=============
-
-- Router A:
-
-.. code-block:: none
-
- set interfaces ethernet eth0 address '10.0.0.1/24'
- set interfaces ethernet eth1 address '192.168.0.1/32'
- set interfaces ethernet eth1 ip ospf authentication md5 key-id 1 md5-key 'yourpassword'
- set interfaces ethernet eth1 ip ospf network 'point-to-point'
- set interfaces ethernet eth2 address '192.168.0.1/32'
- set interfaces ethernet eth2 ip ospf authentication md5 key-id 1 md5-key 'yourpassword'
- set interfaces ethernet eth2 ip ospf network 'point-to-point'
- set interfaces loopback lo address '192.168.0.1/32'
- set protocols ospf area 0.0.0.0 authentication 'md5'
- set protocols ospf area 0.0.0.0 network '192.168.0.1/32'
- set protocols ospf parameters router-id '192.168.0.1'
- set protocols ospf redistribute connected
-
-- Router B:
-
-.. code-block:: none
-
- set interfaces ethernet eth0 address '10.0.0.2/24'
- set interfaces ethernet eth1 address '192.168.0.2/32'
- set interfaces ethernet eth1 ip ospf authentication md5 key-id 1 md5-key 'yourpassword'
- set interfaces ethernet eth1 ip ospf network 'point-to-point'
- set interfaces ethernet eth2 address '192.168.0.2/32'
- set interfaces ethernet eth2 ip ospf authentication md5 key-id 1 md5-key 'yourpassword'
- set interfaces ethernet eth2 ip ospf network 'point-to-point'
- set interfaces loopback lo address '192.168.0.2/32'
- set protocols ospf area 0.0.0.0 authentication 'md5'
- set protocols ospf area 0.0.0.0 network '192.168.0.2/32'
- set protocols ospf parameters router-id '192.168.0.2'
- set protocols ospf redistribute connected
-
-
-Results
-=======
-
-- Router A:
-
-.. code-block:: none
-
- vyos@vyos:~$ show interfaces
- Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
- Interface IP Address S/L Description
- --------- ---------- --- -----------
- eth0 10.0.0.1/24 u/u
- eth1 192.168.0.1/32 u/u
- eth2 192.168.0.1/32 u/u
- lo 127.0.0.1/8 u/u
- 192.168.0.1/32
- ::1/128
-
-.. code-block:: none
-
- vyos@vyos:~$ show ip route
- Codes: K - kernel route, C - connected, S - static, R - RIP,
- O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
- T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
- F - PBR, f - OpenFabric,
- > - selected route, * - FIB route, q - queued route, r - rejected route
-
- S>* 0.0.0.0/0 [210/0] via 10.0.0.254, eth0, 00:57:34
- O 10.0.0.0/24 [110/20] via 192.168.0.2, eth1 onlink, 00:13:21
- via 192.168.0.2, eth2 onlink, 00:13:21
- C>* 10.0.0.0/24 is directly connected, eth0, 00:57:35
- O 192.168.0.1/32 [110/0] is directly connected, lo, 00:48:53
- C * 192.168.0.1/32 is directly connected, eth2, 00:56:31
- C * 192.168.0.1/32 is directly connected, eth1, 00:56:31
- C>* 192.168.0.1/32 is directly connected, lo, 00:57:36
- O>* 192.168.0.2/32 [110/1] via 192.168.0.2, eth1 onlink, 00:29:03
- * via 192.168.0.2, eth2 onlink, 00:29:03
-
-- Router B:
-
-.. code-block:: none
-
- vyos@vyos:~$ show interfaces
- Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
- Interface IP Address S/L Description
- --------- ---------- --- -----------
- eth0 10.0.0.2/24 u/u
- eth1 192.168.0.2/32 u/u
- eth2 192.168.0.2/32 u/u
- lo 127.0.0.1/8 u/u
- 192.168.0.2/32
- ::1/128
-
-.. code-block:: none
-
- vyos@vyos:~$ show ip route
- Codes: K - kernel route, C - connected, S - static, R - RIP,
- O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP,
- T - Table, v - VNC, V - VNC-Direct, A - Babel, D - SHARP,
- F - PBR, f - OpenFabric,
- > - selected route, * - FIB route, q - queued route, r - rejected route
-
- S>* 0.0.0.0/0 [210/0] via 10.0.0.254, eth0, 00:57:34
- O 10.0.0.0/24 [110/20] via 192.168.0.1, eth1 onlink, 00:13:21
- via 192.168.0.1, eth2 onlink, 00:13:21
- C>* 10.0.0.0/24 is directly connected, eth0, 00:57:35
- O 192.168.0.2/32 [110/0] is directly connected, lo, 00:48:53
- C * 192.168.0.2/32 is directly connected, eth2, 00:56:31
- C * 192.168.0.2/32 is directly connected, eth1, 00:56:31
- C>* 192.168.0.2/32 is directly connected, lo, 00:57:36
- O>* 192.168.0.1/32 [110/1] via 192.168.0.1, eth1 onlink, 00:29:03
- * via 192.168.0.1, eth2 onlink, 00:29:03
diff --git a/docs/appendix/examples/tunnelbroker-ipv6.rst b/docs/appendix/examples/tunnelbroker-ipv6.rst
deleted file mode 100644
index 868b225f..00000000
--- a/docs/appendix/examples/tunnelbroker-ipv6.rst
+++ /dev/null
@@ -1,169 +0,0 @@
-.. _examples-tunnelbroker-ipv6:
-
-#######################
-Tunnelbroker.net (IPv6)
-#######################
-
-This guides walks through the setup of https://www.tunnelbroker.net/ for an
-IPv6 Tunnel.
-
-Prerequisites
-=============
-
-- A public, routable IPv4 address. This does not necessarily need to be static,
- but you will need to update the tunnel endpoint when/if your IP address
- changes, which can be done with a script and a scheduled task.
-- Account at https://www.tunnelbroker.net/
-- Requested a "Regular Tunnel". You want to choose a location that is closest
- to your physical location for the best response time.
-
-Setup initial tunnel
-====================
-
-Set up initial IPv6 tunnel. Replace the field below from the fields on the
-tunnel information page.
-
-.. code-block:: none
-
- conf
- set interfaces tunnel tun0 address Client_IPv6_from_Tunnelbroker # This will be your VyOS install's public IPv6 address
- set interfaces tunnel tun0 description 'HE.NET IPv6 Tunnel'
- set interfaces tunnel tun0 encapsulation 'sit'
- set interfaces tunnel tun0 local-ip Client_IPv4_from_Tunnelbroker # This is your public IP
- set interfaces tunnel tun0 mtu '1472'
- set interfaces tunnel tun0 multicast 'disable'
- set interfaces tunnel tun0 remote-ip Server_IPv4_from_Tunnelbroker # This is the IP of the Tunnelbroker server
- set protocols static interface-route6 ::/0 next-hop-interface tun0 # Tell all traffic to go over this tunnel
- commit
-
-If your WAN connection is over PPPoE, you may need to set the MTU on the above
-tunnel lower than 1472.
-
-At this point you should be able to ping an IPv6 address, try pinging Google:
-
-.. code-block:: none
-
- ping6 -c2 2001:4860:4860::8888
-
- 64 bytes from 2001:4860:4860::8888: icmp_seq=1 ttl=57 time=21.7 ms
- 64 bytes from 2001:4860:4860::8888: icmp_seq=2 ttl=57 time=21.1 ms
-
- --- 2001:4860:4860::8888 ping statistics ---
- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms
- rtt min/avg/max/mdev = 21.193/21.459/21.726/0.304 ms
-
-Assuming the pings are successful, you need to add some DNS servers.
-Some options:
-
-.. code-block:: none
-
- set system name-server 2001:4860:4860::8888 # Google
- set system name-server 2001:4860:4860::8844 # Google
- set system name-server 2606:4700:4700::1111 # Cloudflare
- set system name-server 2606:4700:4700::1001 # Cloudflare
- commit
-
-You should now be able to ping something by IPv6 DNS name:
-
-.. code-block:: none
-
- # ping6 -c2 one.one.one.one
- PING one.one.one.one(one.one.one.one) 56 data bytes
- 64 bytes from one.one.one.one: icmp_seq=1 ttl=58 time=16.8 ms
- 64 bytes from one.one.one.one: icmp_seq=2 ttl=58 time=17.4 ms
-
- --- one.one.one.one ping statistics ---
- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms
- rtt min/avg/max/mdev = 16.880/17.153/17.426/0.273 ms
-
-Assuming everything works, you can proceed to client configuration
-
-LAN Configuration
-=================
-
-At this point your VyOS install should have full IPv6, but now your LAN devices
-need access.
-
-With Tunnelbroker.net, you have two options:
-
-- Routed /64. This is the default assignment. In IPv6-land, it's good for a
- single "LAN", and is somewhat equivalent to a /24.
- Example: `2001:470:xxxx:xxxx::/64`
-- Routed /48. This is something you can request by clicking the "Assign /48"
- link in the Tunnelbroker.net tunnel config. It allows you to have up to 65k
- LANs. Example: `2001:470:xxxx::/48`
-
-Unlike IPv4, IPv6 is really not designed to be broken up smaller than /64. So
-if you ever want to have multiple LANs, VLANs, DMZ, etc, you'll want to ignore
-the assigned /64, and request the /48 and use that.
-
-Single LAN Setup
-================
-
-Single LAN setup where eth1 is your LAN interface. Use the /64 (all the xxxx
-should be replaced with the information from your `Routed /64` tunnel):
-
-.. code-block:: none
-
- set interfaces ethernet eth1 address '2001:470:xxxx:xxxx::1/64'
- set service router-advert interface eth1 name-server '2001:4860:4860::8888'
- set service router-advert interface eth1 name-server '2001:4860:4860::8844'
- set service router-advert interface eth1 prefix 2001:470:xxxx:xxxx::/64
-
-Please note, 'autonomous-flag' and 'on-link-flag' are enabled by default, 'valid-lifetime' and 'preferred-lifetime' are set to default values of 30 days and 4 hours respectively.
-
-This accomplishes a few things:
-
-- Sets your LAN interface's IP address
-- Enables router advertisements. This is an IPv6 alternative for DHCP (though
- DHCPv6 can still be used). With RAs, Your devices will automatically find the
- information they need for routing and DNS.
-
-Multiple LAN/DMZ Setup
-======================
-
-In this, you use the `Routed /48` information. This allows you to assign a
-different /64 to every interface, LAN, or even device. Or you could break your
-network into smaller chunks like /56 or /60.
-
-The format of these addresses:
-
-- `2001:470:xxxx::/48`: The whole subnet. xxxx should come from Tunnelbroker.
-- `2001:470:xxxx:1::/64`: A subnet suitable for a LAN
-- `2001:470:xxxx:2::/64`: Another subnet
-- `2001:470:xxxx:ffff:/64`: The last usable /64 subnet.
-
-In the above examples, 1,2,ffff are all chosen by you. You can use 1-ffff
-(1-65535).
-
-So, when your LAN is eth1, your DMZ is eth2, your cameras live on eth3, etc:
-
-.. code-block:: none
-
- set interfaces ethernet eth1 address '2001:470:xxxx:1::1/64'
- set service router-advert interface eth1 name-server '2001:4860:4860::8888'
- set service router-advert interface eth1 name-server '2001:4860:4860::8844'
- set service router-advert interface eth1 prefix 2001:470:xxxx:1::/64
-
- set interfaces ethernet eth2 address '2001:470:xxxx:2::1/64'
- set service router-advert interface eth2 name-server '2001:4860:4860::8888'
- set service router-advert interface eth2 name-server '2001:4860:4860::8844'
- set service router-advert interface eth2 prefix 2001:470:xxxx:2::/64
-
- set interfaces ethernet eth3 address '2001:470:xxxx:3::1/64'
- set service router-advert interface eth3 name-server '2001:4860:4860::8888'
- set service router-advert interface eth3 name-server '2001:4860:4860::8844'
- set service router-advert interface eth3 prefix 2001:470:xxxx:3::/64
-
-Please note, 'autonomous-flag' and 'on-link-flag' are enabled by default, 'valid-lifetime' and 'preferred-lifetime' are set to default values of 30 days and 4 hours respectively.
-
-Firewall
-========
-
-Finally, don't forget the :ref:`firewall`. The usage is identical, except for
-instead of `set firewall name NAME`, you would use `set firewall ipv6-name
-NAME`.
-
-Similarly, to attach the firewall, you would use `set interfaces ethernet eth0
-firewall in ipv6-name` or `set zone-policy zone LOCAL from WAN firewall
-ipv6-name`.
diff --git a/docs/appendix/examples/wan-load-balancing.rst b/docs/appendix/examples/wan-load-balancing.rst
deleted file mode 100644
index 7093defe..00000000
--- a/docs/appendix/examples/wan-load-balancing.rst
+++ /dev/null
@@ -1,170 +0,0 @@
-.. _wan-load-balancing:
-
-WAN Load Balancer examples
-==========================
-
-
-Example 1: Distributing load evenly
------------------------------------
-
-The setup used in this example is shown in the following diagram:
-
-.. image:: /_static/images/Wan_load_balancing1.png
- :width: 80%
- :align: center
- :alt: Network Topology Diagram
-
-
-Overview
-^^^^^^^^
- * All traffic coming in trough eth2 is balanced between eth0 and eth1
- on the router.
- * Pings will be sent to four targets for health testing (33.44.55.66,
- 44.55.66.77, 55.66.77.88 and 66.77.88.99).
- * All outgoing packets are assigned the source address of the assigned
- interface (SNAT).
- * eth0 is set to be removed from the load balancer's interface pool
- after 5 ping failures, eth1 will be removed after 4 ping failures.
-
-Create static routes to ping targets
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-Create static routes through the two ISPs towards the ping targets and
-commit the changes:
-
-.. code-block:: none
-
- set protocols static route 33.44.55.66/32 next-hop 11.22.33.1
- set protocols static route 44.55.66.77/32 next-hop 11.22.33.1
- set protocols static route 55.66.77.88/32 next-hop 22.33.44.1
- set protocols static route 66.77.88.99/32 next-hop 22.33.44.1
-
-Configure the load balancer
-^^^^^^^^^^^^^^^^^^^^^^^^^^^
-Configure the WAN load balancer with the parameters described above:
-
-.. code-block:: none
-
- set load-balancing wan interface-health eth0 failure-count 5
- set load-balancing wan interface-health eth0 nexthop 11.22.33.1
- set load-balancing wan interface-health eth0 test 10 type ping
- set load-balancing wan interface-health eth0 test 10 target 33.44.55.66
- set load-balancing wan interface-health eth0 test 20 type ping
- set load-balancing wan interface-health eth0 test 20 target 44.55.66.77
- set load-balancing wan interface-health eth1 failure-count 4
- set load-balancing wan interface-health eth1 nexthop 22.33.44.1
- set load-balancing wan interface-health eth1 test 10 type ping
- set load-balancing wan interface-health eth1 test 10 target 55.66.77.88
- set load-balancing wan interface-health eth1 test 20 type ping
- set load-balancing wan interface-health eth1 test 20 target 66.77.88.99
- set load-balancing wan rule 10 inbound-interface eth2
- set load-balancing wan rule 10 interface eth0
- set load-balancing wan rule 10 interface eth1
-
-Example 2: Failover based on interface weights
-----------------------------------------------
-
-This examples uses the failover mode.
-
-Overview
-^^^^^^^^
-In this example eth0 is the primary interface and eth1 is the secondary
-interface to provide simple failover functionality. If eth0 fails, eth1
-takes over.
-
-Create interface weight based configuration
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-The configuration steps are the same as in the previous example, except
-rule 10 so we keep the configuration, remove rule 10 and add a new rule
-for the failover mode:
-
-.. code-block:: none
-
- delete load-balancing wan rule 10
- set load-balancing wan rule 10 failover
- set load-balancing wan rule 10 inbound-interface eth2
- set load-balancing wan rule 10 interface eth0 weight 10
- set load-balancing wan rule 10 interface eth1 weight 1
-
-Example 3: Failover based on rule order
----------------------------------------
-
-The previous example used the failover command to send traffic thorugh
-eth1 if eth0 fails. In this example failover functionality is provided
-by rule order.
-
-Overview
-^^^^^^^^
-Two rules will be created, the first rule directs traffic coming in
-from eth2 to eth0 and the second rule directs the traffic to eth1. If
-eth0 fails the first rule is bypassed and the second rule matches,
-directing traffic to eth1.
-
-Create rule order based configuration
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-We keep the configurtation from the previous example, delete rule 10
-and create the two new rules as described:
-
-.. code-block:: none
-
- delete load-balancing wan rule 10
- set load-balancing wan rule 10 inbound-interface eth2
- set load-balancing wan rule 10 interface eth0
- set load-balancing wan rule 20 inbound-interface eth2
- set load-balancing wan rule 20 interface eth1
-
-Example 4: Failover based on rule order - priority traffic
-----------------------------------------------------------
-
-A rule order for prioritising traffic is useful in scenarios where the
-secondary link has a lower speed and should only carry high priority
-traffic. It is assumed for this example that eth1 is connected to a
-slower connection than eth0 and should prioritise VoIP traffic.
-
-Overview
-^^^^^^^^
-A rule order for prioritising traffic is useful in scenarios where the
-secondary link has a lower speed and should only carry high priority
-traffic. It is assumed for this example that eth1 is connected to a
-slower connection than eth0 and should prioritise VoIP traffic.
-
-Create rule order based configuration with low speed secondary link
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-We keep the configuration from the previous example, delete rule 20 and
-create a new rule as described:
-
-.. code-block:: none
-
- delete load-balancing wan rule 20
- set load-balancing wan rule 20 inbound-interface eth2
- set load-balancing wan rule 20 interface eth1
- set load-balancing wan rule 20 destination port sip
- set load-balancing wan rule 20 protocol tcp
- set protocols static route 0.0.0.0/0 next-hop 11.22.33.1
-
-Example 5: Exclude traffic from load balancing
-----------------------------------------------
-
-In this example two LAN interfaces exist in different subnets instead
-of one like in the previous examples:
-
-.. image:: /_static/images/Wan_load_balancing_exclude1.png
- :width: 80%
- :align: center
- :alt: Network Topology Diagram
-
-Adding a rule for the second interface
-^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
-
-Based on the previous example, another rule for traffic from the second
-interface eth3 can be added to the load balancer. However, traffic meant
-to flow between the LAN subnets will be sent to eth0 and eth1 as well.
-To prevent this, another rule is required. This rule excludes traffic
-between the local subnets from the load balancer. It also excludes
-locally-sources packets (required for web caching with load balancing).
-eth+ is used as an alias that refers to all ethernet interfaces:
-
-.. code-block:: none
-
- set load-balancing wan rule 5 exclude
- set load-balancing wan rule 5 inbound-interface eth+
- set load-balancing wan rule 5 destination address 10.0.0.0/8
diff --git a/docs/appendix/examples/zone-policy.rst b/docs/appendix/examples/zone-policy.rst
deleted file mode 100644
index bfe77c2e..00000000
--- a/docs/appendix/examples/zone-policy.rst
+++ /dev/null
@@ -1,415 +0,0 @@
-.. _examples-zone-policy:
-
-Zone-Policy example
--------------------
-
-Native IPv4 and IPv6
-^^^^^^^^^^^^^^^^^^^^
-
-We have three networks.
-
-.. code-block:: none
-
- WAN - 172.16.10.0/24, 2001:0DB8:0:9999::0/64
- LAN - 192.168.100.0/24, 2001:0DB8:0:AAAA::0/64
- DMZ - 192.168.200.0/24, 2001:0DB8:0:BBBB::0/64
-
-
-**This specific example is for a router on a stick, but is very easily
-adapted for however many NICs you have**:
-
-
-* Internet - 192.168.200.100 - TCP/80
-* Internet - 192.168.200.100 - TCP/443
-* Internet - 192.168.200.100 - TCP/25
-* Internet - 192.168.200.100 - TCP/53
-* VyOS actis as DHCP, DNS forwarder, NAT, router and firewall.
-* 192.168.200.200/2001:0DB8:0:BBBB::200 is an internal/external DNS, web
- and mail (SMTP/IMAP) server.
-* 192.168.100.10/2001:0DB8:0:AAAA::10 is the administrator's console. It
- can SSH to VyOS.
-* LAN and DMZ hosts have basic outbound access: Web, FTP, SSH.
-* LAN can access DMZ resources.
-* DMZ cannot access LAN resources.
-* Inbound WAN connect to DMZ host.
-
-.. image:: /_static/images/zone-policy-diagram.png
- :width: 80%
- :align: center
- :alt: Network Topology Diagram
-
-The VyOS interface is assigned the .1/:1 address of their respective
-networks. WAN is on VLAN 10, LAN on VLAN 20, and DMZ on VLAN 30.
-
-It will look something like this:
-
-.. code-block:: none
-
- interfaces {
- ethernet eth0 {
- duplex auto
- hw-id 00:53:ed:6e:2a:92
- smp_affinity auto
- speed auto
- vif 10 {
- address 172.16.10.1/24
- address 2001:db8:0:9999::1/64
- }
- vif 20 {
- address 192.168.100.1/24
- address 2001:db8:0:AAAA::1/64
- }
- vif 30 {
- address 192.168.200.1/24
- address 2001:db8:0:BBBB::1/64
- }
- }
- loopback lo {
- }
- }
-
-
-Zones Basics
-^^^^^^^^^^^^
-
-Each interface is assigned to a zone. The interface can be physical or
-virtual such as tunnels (VPN, PPTP, GRE, etc) and are treated exactly
-the same.
-
-Traffic flows from zone A to zone B. That flow is what I refer to as a
-zone-pair-direction. eg. A->B and B->A are two zone-pair-destinations.
-
-Ruleset are created per zone-pair-direction.
-
-I name rule sets to indicate which zone-pair-direction they represent.
-eg. ZoneA-ZoneB or ZoneB-ZoneA. LAN-DMZ, DMZ-LAN.
-
-In VyOS, you have to have unique Ruleset names. In the event of overlap,
-I add a "-6" to the end of v6 rulesets. eg. LAN-DMZ, LAN-DMZ-6. This
-allows for each auto-completion and uniqueness.
-
-In this example we have 4 zones. LAN, WAN, DMZ, Local. The local zone is
-the firewall itself.
-
-If your computer is on the LAN and you need to SSH into your VyOS box,
-you would need a rule to allow it in the LAN-Local ruleset. If you want
-to access a webpage from your VyOS box, you need a rule to allow it in
-the Local-LAN ruleset.
-
-In rules, it is good to keep them named consistently. As the number of
-rules you have grows, the more consistency you have, the easier your
-life will be.
-
-.. code-block:: none
-
- Rule 1 - State Established, Related
- Rule 2 - State Invalid
- Rule 100 - ICMP
- Rule 200 - Web
- Rule 300 - FTP
- Rule 400 - NTP
- Rule 500 - SMTP
- Rule 600 - DNS
- Rule 700 - DHCP
- Rule 800 - SSH
- Rule 900 - IMAPS
-
-The first two rules are to deal with the idiosyncrasies of VyOS and
-iptables.
-
-Zones and Rulesets both have a default action statement. When using
-Zone-Policies, the default action is set by the zone-policy statement
-and is represented by rule 10000.
-
-It is good practice to log both accepted and denied traffic. It can save
-you significant headaches when trying to troubleshoot a connectivity
-issue.
-
-To add logging to the default rule, do:
-
-.. code-block:: none
-
- set firewall name <ruleSet> enable-default-log
-
-
-By default, iptables does not allow traffic for established session to
-return, so you must explicitly allow this. I do this by adding two rules
-to every ruleset. 1 allows established and related state packets through
-and rule 2 drops and logs invalid state packets. We place the
-established/related rule at the top because the vast majority of traffic
-on a network is established and the invalid rule to prevent invalid
-state packets from mistakenly being matched against other rules. Having
-the most matched rule listed first reduces CPU load in high volume
-environments. Note: I have filed a bug to have this added as a default
-action as well.
-
-''It is important to note, that you do not want to add logging to the
-established state rule as you will be logging both the inbound and
-outbound packets for each session instead of just the initiation of the
-session. Your logs will be massive in a very short period of time.''
-
-In VyOS you must have the interfaces created before you can apply it to
-the zone and the rulesets must be created prior to applying it to a
-zone-policy.
-
-I create/configure the interfaces first. Build out the rulesets for each
-zone-pair-direction which includes at least the three state rules. Then
-I setup the zone-policies.
-
-Zones do not allow for a default action of accept; either drop or
-reject. It is important to remember this because if you apply an
-interface to a zone and commit, any active connections will be dropped.
-Specifically, if you are SSH’d into VyOS and add local or the interface
-you are connecting through to a zone and do not have rulesets in place
-to allow SSH and established sessions, you will not be able to connect.
-
-The following are the rules that were created for this example (may not
-be complete), both in IPv4 and IPv6. If there is no IP specified, then
-the source/destination address is not explicit.
-
-.. code-block:: none
-
- WAN – DMZ:192.168.200.200 – tcp/80
- WAN – DMZ:192.168.200.200 – tcp/443
- WAN – DMZ:192.168.200.200 – tcp/25
- WAN – DMZ:192.168.200.200 – tcp/53
- WAN – DMZ:2001:0DB8:0:BBBB::200 – tcp/80
- WAN – DMZ:2001:0DB8:0:BBBB::200 – tcp/443
- WAN – DMZ:2001:0DB8:0:BBBB::200 – tcp/25
- WAN – DMZ:2001:0DB8:0:BBBB::200 – tcp/53
-
- DMZ - Local - tcp/53
- DMZ - Local - tcp/123
- DMZ - Local - tcp/67,68
-
- LAN - Local - tcp/53
- LAN - Local - tcp/123
- LAN - Local - tcp/67,68
- LAN:192.168.100.10 - Local - tcp/22
- LAN:2001:0DB8:0:AAAA::10 - Local - tcp/22
-
- LAN - WAN - tcp/80
- LAN - WAN - tcp/443
- LAN - WAN - tcp/22
- LAN - WAN - tcp/20,21
-
- DMZ - WAN - tcp/80
- DMZ - WAN - tcp/443
- DMZ - WAN - tcp/22
- DMZ - WAN - tcp/20,21
- DMZ - WAN - tcp/53
- DMZ - WAN - udp/53
-
- Local - WAN - tcp/80
- Local - WAN - tcp/443
- Local - WAN - tcp/20,21
-
- Local - DMZ - tcp/25
- Local - DMZ - tcp/67,68
- Local - DMZ - tcp/53
- Local - DMZ - udp/53
-
- Local - LAN - tcp/67,68
-
- LAN - DMZ - tcp/80
- LAN - DMZ - tcp/443
- LAN - DMZ - tcp/993
- LAN:2001:0DB8:0:AAAA::10 - DMZ:2001:0DB8:0:BBBB::200 - tcp/22
- LAN:192.168.100.10 - DMZ:192.168.200.200 - tcp/22
-
-Since we have 4 zones, we need to setup the following rulesets.
-
-.. code-block:: none
-
- Lan-wan
- Lan-local
- Lan-dmz
- Wan-lan
- Wan-local
- Wan-dmz
- Local-lan
- Local-wan
- Local-dmz
- Dmz-lan
- Dmz-wan
- Dmz-local
-
-Even if the two zones will never communicate, it is a good idea to
-create the zone-pair-direction rulesets and set enable-default-log. This
-will allow you to log attempts to access the networks. Without it, you
-will never see the connection attempts.
-
-This is an example of the three base rules.
-
-.. code-block:: none
-
- name wan-lan {
- default-action drop
- enable-default-log
- rule 1 {
- action accept
- state {
- established enable
- related enable
- }
- }
- rule 2 {
- action drop
- log enable
- state {
- invalid enable
- }
- }
- }
-
-
-Here is an example of an IPv6 DMZ-WAN ruleset.
-
-.. code-block:: none
-
- ipv6-name dmz-wan-6 {
- default-action drop
- enable-default-log
- rule 1 {
- action accept
- state {
- established enable
- related enable
- }
- }
- rule 2 {
- action drop
- log enable
- state {
- invalid enable
- }
- rule 100 {
- action accept
- log enable
- protocol ipv6-icmp
- }
- rule 200 {
- action accept
- destination {
- port 80,443
- }
- log enable
- protocol tcp
- }
- rule 300 {
- action accept
- destination {
- port 20,21
- }
- log enable
- protocol tcp
- }
- rule 500 {
- action accept
- destination {
- port 25
- }
- log enable
- protocol tcp
- source {
- address 2001:db8:0:BBBB::200
- }
- }
- rule 600 {
- action accept
- destination {
- port 53
- }
- log enable
- protocol tcp_udp
- source {
- address 2001:db8:0:BBBB::200
- }
- }
- rule 800 {
- action accept
- destination {
- port 22
- }
- log enable
- protocol tcp
- }
- }
-
-Once you have all of your rulesets built, then you need to create your
-zone-policy.
-
-Start by setting the interface and default action for each zone.
-
-.. code-block:: none
-
- set zone-policy zone dmz default-action drop
- set zone-policy zone dmz interface eth0.30
-
-In this case, we are setting the v6 ruleset that represents traffic
-sourced from the LAN, destined for the DMZ. Because the zone-policy
-firewall syntax is a little awkward, I keep it straight by thinking of
-it backwards.
-
-.. code-block:: none
-
- set zone-policy zone dmz from lan firewall ipv6-name lan-dmz-6
-
-DMZ-LAN policy is LAN-DMZ. You can get a rhythm to it when you build out
-a bunch at one time.
-
-In the end, you will end up with something like this config. I took out
-everything but the Firewall, Interfaces, and zone-policy sections. It is
-long enough as is.
-
-
-IPv6 Tunnel
-^^^^^^^^^^^
-
-If you are using a IPv6 tunnel from HE.net or someone else, the basis is
-the same except you have two WAN interface. One for v4 and one for v6.
-
-You would have 5 zones instead of just 4 and you would configure your v6
-ruleset between your tunnel interface and your LAN/DMZ zones instead of
-to the WAN.
-
-LAN, WAN, DMZ, local and TUN (tunnel)
-
-v6 pairs would be:
-
-.. code-block:: none
-
- lan-tun
- lan-local
- lan-dmz
- tun-lan
- tun-local
- tun-dmz
- local-lan
- local-tun
- local-dmz
- dmz-lan
- dmz-tun
- dmz-local
-
-Notice, none go to WAN since WAN wouldn't have a v6 address on it.
-
-You would have to add a couple of rules on your wan-local ruleset to
-allow protocol 41 in.
-
-Something like:
-
-.. code-block:: none
-
- rule 400 {
- action accept
- destination {
- address 172.16.10.1
- }
- log enable
- protocol 41
- source {
- address ip.of.tunnel.broker
- }
- }
-
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-26 11:50:45 +0000