sort IP commands under configuration

2 files changed, 252 insertions, 4 deletions

diff --git a/docs/configuration/system/ip.rst b/docs/configuration/system/ip.rst
index 74116eb0..78aeef4e 100644
--- a/docs/configuration/system/ip.rst
+++ b/docs/configuration/system/ip.rst
@@ -1,2 +1,70 @@
-ip
-##
\ No newline at end of file
+##
+IP
+##
+
+System configuration commands
+-----------------------------
+
+.. cfgcmd:: set system ip disable-forwarding
+
+   Use this command to disable IPv4 forwarding on all interfaces.
+
+.. cfgcmd:: set system ip arp table-size <number>
+
+   Use this command to define the maximum number of entries to keep in
+   the ARP cache (1024, 2048, 4096, 8192, 16384, 32768).
+
+.. cfgcmd:: set system ip multipath layer4-hashing
+
+   Use this command to use Layer 4 information for IPv4 ECMP hashing.
+
+
+Operational commands
+--------------------
+
+show commands
+^^^^^^^^^^^^^
+
+See below the different parameters available for the IPv4 **show** command:
+
+.. code-block:: none
+
+   vyos@vyos:~$ show ip
+   Possible completions:
+     access-list   Show all IP access-lists
+     as-path-access-list
+                   Show all as-path-access-lists
+     bgp           Show Border Gateway Protocol (BGP) information
+     community-list
+                   Show IP community-lists
+     extcommunity-list
+                   Show extended IP community-lists
+     forwarding    Show IP forwarding status
+     groups        Show IP multicast group membership
+     igmp          Show IGMP (Internet Group Management Protocol) information
+     large-community-list
+                   Show IP large-community-lists
+     multicast     Show IP multicast
+     ospf          Show IPv4 Open Shortest Path First (OSPF) routing information
+     pim           Show PIM (Protocol Independent Multicast) information
+     ports         Show IP ports in use by various system services
+     prefix-list   Show all IP prefix-lists
+     protocol      Show IP route-maps per protocol
+     rip           Show Routing Information Protocol (RIP) information
+     route         Show IP routes
+
+
+reset commands
+^^^^^^^^^^^^^^
+
+And the different IPv4 **reset** commands available:
+
+.. code-block:: none
+
+   vyos@vyos:~$ reset ip
+   Possible completions:
+     arp           Reset Address Resolution Protocol (ARP) cache
+     bgp           Clear Border Gateway Protocol (BGP) statistics or status
+     igmp          IGMP clear commands
+     multicast     IP multicast routing table
+     route         Reset IP route
\ No newline at end of file
diff --git a/docs/configuration/system/ipv6.rst b/docs/configuration/system/ipv6.rst
index 19ed6d62..cba5c0e0 100644
--- a/docs/configuration/system/ipv6.rst
+++ b/docs/configuration/system/ipv6.rst
@@ -1,2 +1,182 @@
-ipv6
-####
\ No newline at end of file
+####
+IPv6
+####
+
+System configuration commands
+-----------------------------
+
+.. cfgcmd:: set system ipv6 disable
+
+   Use this command to disable assignment of IPv6 addresses on all
+   interfaces.
+
+.. cfgcmd:: set system ipv6 disable-forwarding
+
+   Use this command to disable IPv6 forwarding on all interfaces.
+
+.. cfgcmd:: set system ipv6 neighbor table-size <number>
+
+   Use this command to define the maximum number of entries to keep in
+   the Neighbor cache (1024, 2048, 4096, 8192, 16384, 32768).
+
+.. cfgcmd:: set system ipv6 strict-dad
+
+   Use this command to disable IPv6 operation on interface when
+   Duplicate Address Detection fails on Link-Local address.
+
+.. cfgcmd:: set system ipv6 multipath layer4-hashing
+
+   Use this command to user Layer 4 information for ECMP hashing.
+
+
+Operational commands
+--------------------
+
+Show commands
+^^^^^^^^^^^^^
+
+.. opcmd:: show ipv6 neighbors
+
+   Use this command to show IPv6 Neighbor Discovery Protocol information.
+
+.. opcmd:: show ipv6 groups
+
+   Use this command to show IPv6 multicast group membership.
+
+.. opcmd:: show ipv6 forwarding
+
+   Use this command to show IPv6 forwarding status.
+
+.. opcmd:: show ipv6 route
+
+   Use this command to show IPv6 routes.
+
+   Check the many parameters available for the `show ipv6 route` command:
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show ipv6 route
+      Possible completions:
+        <Enter>       Execute the current command
+        <X:X::X:X>    Show IPv6 routes of given address or prefix
+        <X:X::X:X/M>
+        bgp           Show IPv6 BGP routes
+        cache         Show kernel IPv6 route cache
+        connected     Show IPv6 connected routes
+        forward       Show kernel IPv6 route table
+        isis          Show IPv6 ISIS routes
+        kernel        Show IPv6 kernel routes
+        ospfv3        Show IPv6 OSPF6 routes
+        ripng         Show IPv6 RIPNG routes
+        static        Show IPv6 static routes
+        summary       Show IPv6 routes summary
+        table         Show IP routes in policy table
+        vrf           Show IPv6 routes in VRF
+
+
+.. opcmd:: show ipv6 prefix-list
+
+   Use this command to show all IPv6 prefix lists
+
+   There are different parameters for getting prefix-list information:
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show ipv6 prefix-list
+      Possible completions:
+        <Enter>       Execute the current command
+        <WORD>        Show specified IPv6 prefix-list
+        detail        Show detail of IPv6 prefix-lists
+        summary       Show summary of IPv6 prefix-lists
+
+.. opcmd:: show ipv6 access-list
+
+   Use this command to show all IPv6 access lists
+
+   You can also specify which IPv6 access-list should be shown:
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show ipv6 access-list
+      Possible completions:
+        <Enter>       Execute the current command
+        <text>        Show specified IPv6 access-list
+
+.. opcmd:: show ipv6 bgp
+
+   Use this command to show IPv6 Border Gateway Protocol information.
+
+
+   In addition, you can specify many other parameters to get BGP
+   information:
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show ipv6 bgp
+      Possible completions:
+        <Enter>       Execute the current command
+        <X:X::X:X>    Show BGP information for given address or prefix
+        <X:X::X:X/M>
+        community     Show routes matching the communities
+        community-list
+                      Show routes matching the community-list
+        filter-list   Show routes conforming to the filter-list
+        large-community
+                      Show routes matching the large-community-list
+        large-community-list
+        neighbors     Show detailed information on TCP and BGP neighbor connections
+        prefix-list   Show routes matching the prefix-list
+        regexp        Show routes matching the AS path regular expression
+        route-map     Show BGP routes matching the specified route map
+        summary       Show summary of BGP neighbor status
+
+
+.. opcmd:: show ipv6 ospfv3
+
+   Use this command to get information about OSPFv3.
+
+   You can get more specific OSPFv3 information by using the parameters
+   shown below:
+
+   .. code-block:: none
+
+      vyos@vyos:~$ show ipv6 ospfv3
+      Possible completions:
+        <Enter>       Execute the current command
+        area          Show OSPFv3 spf-tree information
+        border-routers
+                      Show OSPFv3 border-router (ABR and ASBR) information
+        database      Show OSPFv3 Link state database information
+        interface     Show OSPFv3 interface information
+        linkstate     Show OSPFv3 linkstate routing information
+        neighbor      Show OSPFv3 neighbor information
+        redistribute  Show OSPFv3 redistribute External information
+        route         Show OSPFv3 routing table information
+
+.. opcmd:: show ipv6 ripng
+
+   Use this command to get information about the RIPNG protocol
+
+.. opcmd:: show ipv6 ripng status
+
+   Use this command to show the status of the RIPNG protocol
+
+
+Reset commands
+^^^^^^^^^^^^^^
+
+.. opcmd:: reset ipv6 bgp <address>
+
+   Use this command to clear Border Gateway Protocol statistics or
+   status.
+
+
+.. opcmd:: reset ipv6 neighbors <address | interface>
+
+   Use this command to reset IPv6 Neighbor Discovery Protocol cache for
+   an address or interface.
+
+.. opcmd:: reset ipv6 route cache
+
+   Use this command to flush the kernel IPv6 route cache.
+   An address can be added to flush it only for that route.
\ No newline at end of file