Merge pull request #43 from kmpm/features/zone-example

Add the zone-example from wiki

3 files changed, 497 insertions, 0 deletions

diff --git a/docs/examples/dmvpn.rst b/docs/examples/dmvpn.rst
new file mode 100644
index 00000000..d3bf45c7
--- /dev/null
+++ b/docs/examples/dmvpn.rst
@@ -0,0 +1,105 @@
+
+.. _examples-dmvpn:
+
+VyOS DMVPN Hub
+--------------
+
+General infomration can be found in the :ref:`vpn-dmvpn` chapter.
+
+Configuration
+^^^^^^^^^^^^^
+
+.. code-block:: sh
+
+  set interfaces tunnel tun100 address '172.16.253.134/29'
+  set interfaces tunnel tun100 encapsulation 'gre'
+  set interfaces tunnel tun100 local-ip '11.22.33.44'
+  set interfaces tunnel tun100 multicast 'enable'
+  set interfaces tunnel tun100 parameters ip key '1'
+
+  set protocols nhrp tunnel tun100 cisco-authentication '<nhrp secret key>'
+  set protocols nhrp tunnel tun100 holding-time '300'
+  set protocols nhrp tunnel tun100 multicast 'dynamic'
+  set protocols nhrp tunnel tun100 redirect
+  set protocols nhrp tunnel tun100 shortcut
+
+  set vpn ipsec esp-group ESP-HUB compression 'disable'
+  set vpn ipsec esp-group ESP-HUB lifetime '1800'
+  set vpn ipsec esp-group ESP-HUB mode 'tunnel'
+  set vpn ipsec esp-group ESP-HUB pfs 'dh-group2'
+  set vpn ipsec esp-group ESP-HUB proposal 1 encryption 'aes256'
+  set vpn ipsec esp-group ESP-HUB proposal 1 hash 'sha1'
+  set vpn ipsec esp-group ESP-HUB proposal 2 encryption '3des'
+  set vpn ipsec esp-group ESP-HUB proposal 2 hash 'md5'
+  set vpn ipsec ike-group IKE-HUB ikev2-reauth 'no'
+  set vpn ipsec ike-group IKE-HUB key-exchange 'ikev1'
+  set vpn ipsec ike-group IKE-HUB lifetime '3600'
+  set vpn ipsec ike-group IKE-HUB proposal 1 dh-group '2'
+  set vpn ipsec ike-group IKE-HUB proposal 1 encryption 'aes256'
+  set vpn ipsec ike-group IKE-HUB proposal 1 hash 'sha1'
+  set vpn ipsec ike-group IKE-HUB proposal 2 dh-group '2'
+  set vpn ipsec ike-group IKE-HUB proposal 2 encryption 'aes128'
+  set vpn ipsec ike-group IKE-HUB proposal 2 hash 'sha1'
+  set vpn ipsec ipsec-interfaces interface 'eth0'
+
+  set vpn ipsec profile NHRPVPN authentication mode 'pre-shared-secret'
+  set vpn ipsec profile NHRPVPN authentication pre-shared-secret '<secretkey>'
+  set vpn ipsec profile NHRPVPN bind tunnel 'tun100'
+  set vpn ipsec profile NHRPVPN esp-group 'ESP-HUB'
+  set vpn ipsec profile NHRPVPN ike-group 'IKE-HUB'
+
+Cisco IOS Spoke
+^^^^^^^^^^^^^^^
+
+This example is verified with a Cisco 2811 platform running IOS 15.1(4)M9 and
+VyOS 1.1.7 (helium) up to VyOS 1.2 (Crux).
+
+.. code-block:: sh
+
+  Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9-M), Version 15.1(4)M9, RELEASE SOFTWARE (fc3)
+  Technical Support: http://www.cisco.com/techsupport
+  Copyright (c) 1986-2014 by Cisco Systems, Inc.
+  Compiled Fri 12-Sep-14 10:45 by prod_rel_team
+
+  ROM: System Bootstrap, Version 12.3(8r)T7, RELEASE SOFTWARE (fc1)
+
+Use this configuration on your Cisco device:
+
+.. code-block:: sh
+
+  crypto pki token default removal timeout 0
+  crypto keyring DMVPN
+    pre-shared-key address 1.2.3.4 key <secretkey>
+  !
+  crypto isakmp policy 10
+   encr aes 256
+   authentication pre-share
+   group 2
+  !
+  crypto isakmp invalid-spi-recovery
+  crypto isakmp keepalive 30 30 periodic
+  crypto isakmp profile DMVPN
+     keyring DMVPN
+     match identity address 11.22.33.44 255.255.255.255
+  !
+  crypto ipsec transform-set DMVPN-AES256 esp-aes 256 esp-sha-hmac
+   mode transport
+  !
+  crypto ipsec profile DMVPN
+   set security-association idle-time 720
+   set transform-set DMVPN-AES256
+  !
+  interface Tunnel10
+   description Tunnel to DMVPN HUB
+   ip address 172.16.253.129 255.255.255.248
+   no ip redirects
+   ip nhrp authentication <nhrp secret key>
+   ip nhrp map multicast 11.22.33.44
+   ip nhrp map 172.16.253.134 11.22.33.44
+   ip nhrp network-id 1
+   ip nhrp holdtime 600
+   ip nhrp nhs 172.16.253.134
+   ip nhrp registration timeout 75
+   tunnel source Dialer1
+   tunnel mode gre multipoint
+   tunnel key 1
diff --git a/docs/examples/index.rst b/docs/examples/index.rst
new file mode 100644
index 00000000..e976affd
--- /dev/null
+++ b/docs/examples/index.rst
@@ -0,0 +1,13 @@
+.. _examples:
+
+Appendix B - Configuration Examples
+===================================
+
+This chapter contains various configuration Examples
+
+
+.. toctree::
+   :maxdepth: 2
+
+   dmvpn
+   zone-policy
diff --git a/docs/examples/zone-policy.rst b/docs/examples/zone-policy.rst
new file mode 100644
index 00000000..d159d02d
--- /dev/null
+++ b/docs/examples/zone-policy.rst
@@ -0,0 +1,379 @@
+.. _examples-zone-policy:
+
+Zone-Policy example
+-------------------
+
+Native IPv4 and IPv6
+^^^^^^^^^^^^^^^^^^^^
+
+We have three networks.
+
+.. code-block:: sh
+
+  WAN - 172.16.10.0/24, 2001:0DB8:0:9999::0/64
+  LAN - 192.168.100.0/24, 2001:0DB8:0:AAAA::0/64
+  DMZ - 192.168.200.0/24, 2001:0DB8:0:BBBB::0/64
+
+
+This specific example is for a router on a stick, but is very easily adapted
+for however many NICs you have.
+
+[http://imgur.com/Alz1J.png Topology Image]
+
+The VyOS interface is assigned the .1/:1 address of their respective networks.
+WAN is on VLAN 10, LAN on VLAN 20, and DMZ on VLAN 30.
+
+It will look something like this:
+
+.. code-block:: sh
+
+  interfaces {
+      ethernet eth0 {
+          duplex auto
+          hw-id 00:0c:29:6e:2a:92
+          smp_affinity auto
+          speed auto
+          vif 10 {
+              address 172.16.10.1/24
+              address 2001:db8:0:9999::1/64
+          }
+          vif 20 {
+              address 192.168.100.1/24
+              address 2001:db8:0:AAAA::1/64
+          }
+          vif 30 {
+              address 192.168.200.1/24
+              address 2001:db8:0:BBBB::1/64
+          }
+      }
+      loopback lo {
+      }
+  }
+
+
+Zones Basics
+^^^^^^^^^^^^
+
+Each interface is assigned to a zone. The interface can be physical or virtual
+such as tunnels (VPN, pptp, gre, etc) and are treated exactly the same.
+
+Traffic flows from zone A to zone B. That flow is what I refer to as a
+zone-pair-direction. eg. A->B and B->A are two zone-pair-destinations.
+
+Ruleset are created per zone-pair-direction.
+
+I name rule sets to indicate which zone-pair-direction they represent. eg.
+ZoneA-ZoneB or ZoneB-ZoneA. LAN-DMZ, DMZ-LAN.
+
+In VyOS, you have to have unique Ruleset names. In the event of overlap, I
+add a "-6" to the end of v6 rulesets. eg. LAN-DMZ, LAN-DMZ-6. This allows for
+each auto-completion and uniqueness.
+
+In this example we have 4 zones. LAN, WAN, DMZ, Local. The local zone is the
+firewall itself.
+
+If your computer is on the LAN and you need to SSH into your VyOS box, you
+would need a rule to allow it in the LAN-Local ruleset. If you want to access
+a webpage from your VyOS box, you need a rule to allow it in the Local-LAN
+ruleset.
+
+In rules, it is good to keep them named consistently. As the number of rules
+you have grows, the more consistency you have, the easier your life will be.
+
+.. code-block:: sh
+
+  Rule 1 - State Established, Related
+  Rule 2 - State Invalid
+  Rule 100 - ICMP
+  Rule 200 - Web
+  Rule 300 - FTP
+  Rule 400 - NTP
+  Rule 500 - SMTP
+  Rule 600 - DNS
+  Rule 700 - DHCP
+  Rule 800 - SSH
+  Rule 900 - IMAPS
+
+The first two rules are to deal with the idiosyncrasies of VyOS and iptables.
+
+Zones and Rulesets both have a default action statement. When using
+Zone-Policies, the default action is set by the zone-policy statement and is
+represented by rule 10000.
+
+It is good practice to log both accepted and denied traffic. It can save you
+significant headaches when trying to troubleshoot a connectivity issue.
+
+To add logging to the default rule, do:
+
+.. code-block:: sh
+
+  set firewall name <ruleSet> enable-default-log
+
+
+By default, iptables does not allow traffic for established session to return,
+so you must explicitly allow this. I do this by adding two rules to every
+ruleset. 1 allows established and related state packets through and rule 2
+drops and logs invalid state packets. We place the established/related rule at
+the top because the vast majority of traffic on a network is established and
+the invalid rule to prevent invalid state packets from mistakenly being matched
+against other rules. Having the most matched rule listed first reduces CPU load
+in high volume environments. Note: I have filed a bug to have this added as a
+default action as well.
+
+''It is important to note, that you do not want to add logging to the
+established state rule as you will be logging both the inbound and outbound
+packets for each session instead of just the initiation of the session.
+Your logs will be massive in a very short period of time.''
+
+In VyOS you must have the interfaces created before you can apply it to the
+zone and the rulesets must be created prior to applying it to a zone-policy.
+
+I create/configure the interfaces first. Build out the rulesets for each
+zone-pair-direction which includes at least the three state rules. Then I setup
+the zone-policies.
+
+Zones do not allow for a default action of accept; either drop or reject.
+It is important to remember this because if you apply an interface to a zone
+and commit, any active connections will be dropped. Specifically, if you are
+SSH’d into VyOS and add local or the interface you are connecting through to a
+zone and do not have rulesets in place to allow SSH and established sessions,
+you will not be able to connect.
+
+The following are the rules that were created for this example
+(may not be complete), both in IPv4 and IPv6. If there is no IP specified,
+then the source/destination address is not explicit.
+
+.. code-block:: sh
+
+  WAN – DMZ:192.168.200.200 – tcp/80
+  WAN – DMZ:192.168.200.200 – tcp/443
+  WAN – DMZ:192.168.200.200 – tcp/25
+  WAN – DMZ:192.168.200.200 – tcp/53
+  WAN – DMZ:2001:0DB8:0:BBBB::200 – tcp/80
+  WAN – DMZ:2001:0DB8:0:BBBB::200 – tcp/443
+  WAN – DMZ:2001:0DB8:0:BBBB::200 – tcp/25
+  WAN – DMZ:2001:0DB8:0:BBBB::200 – tcp/53
+
+  DMZ - Local - tcp/53
+  DMZ - Local - tcp/123
+  DMZ - Local - tcp/67,68
+
+  LAN - Local - tcp/53
+  LAN - Local - tcp/123
+  LAN - Local - tcp/67,68
+  LAN:192.168.100.10 - Local - tcp/22
+  LAN:2001:0DB8:0:AAAA::10 - Local - tcp/22
+
+  LAN - WAN - tcp/80
+  LAN - WAN - tcp/443
+  LAN - WAN - tcp/22
+  LAN - WAN - tcp/20,21
+
+  DMZ - WAN - tcp/80
+  DMZ - WAN - tcp/443
+  DMZ - WAN - tcp/22
+  DMZ - WAN - tcp/20,21
+  DMZ - WAN - tcp/53
+  DMZ - WAN - udp/53
+
+  Local - WAN - tcp/80
+  Local - WAN - tcp/443
+  Local - WAN - tcp/20,21
+
+  Local - DMZ - tcp/25
+  Local - DMZ - tcp/67,68
+  Local - DMZ - tcp/53
+  Local - DMZ - udp/53
+
+  Local - LAN - tcp/67,68
+
+  LAN - DMZ - tcp/80
+  LAN - DMZ - tcp/443
+  LAN - DMZ - tcp/993
+  LAN:2001:0DB8:0:AAAA::10 - DMZ:2001:0DB8:0:BBBB::200 - tcp/22
+  LAN:192.168.100.10 - DMZ:192.168.200.200 - tcp/22
+
+Since we have 4 zones, we need to setup the following rulesets.
+
+.. code-block:: sh
+
+  Lan-wan
+  Lan-local
+  Lan-dmz
+  Wan-lan
+  Wan-local
+  Wan-dmz
+  Local-lan
+  Local-wan
+  Local-dmz
+  Dmz-lan
+  Dmz-wan
+  Dmz-local
+
+Even if the two zones will never communicate, it is a good idea to create the
+zone-pair-direction rulesets and set enable-default-log. This will allow you to
+log attempts to access the networks. Without it, you will never see the
+connection attempts.
+
+This is an example of the three base rules.
+
+.. code-block:: sh
+
+  name wan-lan {
+    default-action drop
+    enable-default-log
+    rule 1 {
+      action accept
+      state {
+        established enable
+        related enable
+      }
+    }
+    rule 2 {
+      action drop
+      log enable
+      state {
+        invalid enable
+      }
+    }
+  }
+
+
+Here is an example of an IPv6 DMZ-WAN ruleset.
+
+.. code-block:: sh
+
+  ipv6-name dmz-wan-6 {
+    default-action drop
+    enable-default-log
+    rule 1 {
+      action accept
+      state {
+        established enable
+        related enable
+      }
+    }
+    rule 2 {
+      action drop
+      log enable
+      state {
+        invalid enable
+    }
+    rule 100 {
+      action accept
+      log enable
+      protocol ipv6-icmp
+    }
+    rule 200 {
+      action accept
+      destination {
+        port 80,443
+      }
+      log enable
+      protocol tcp
+    }
+    rule 300 {
+      action accept
+      destination {
+        port 20,21
+      }
+      log enable
+      protocol tcp
+    }
+    rule 500 {
+      action accept
+      destination {
+        port 25
+      }
+      log enable
+      protocol tcp
+      source {
+        address 2001:db8:0:BBBB::200
+      }
+    }
+    rule 600 {
+      action accept
+      destination {
+        port 53
+      }
+      log enable
+      protocol tcp_udp
+      source {
+        address 2001:db8:0:BBBB::200
+      }
+    }
+    rule 800 {
+      action accept
+      destination {
+      port 22
+      }
+      log enable
+      protocol tcp
+    }
+  }
+
+Once you have all of your rulesets built, then you need to create your
+zone-policy.
+
+Start by setting the interface and default action for each zone.
+
+.. code-block:: sh
+
+  set zone-policy zone dmz default-action drop
+  set zone-policy zone dmz interface eth0.30
+
+In this case, we are setting the v6 ruleset that represents traffic sourced
+from the LAN, destined for the DMZ.
+Because the zone-policy firewall syntax is a little awkward, I keep it straight
+by thinking of it backwards.
+
+ set zone-policy zone dmz from lan firewall ipv6-name lan-dmz-6
+
+dmz-lan policy is lan-dmz. You can get a rhythm to it when you build out a bunch at one time.
+
+In the end, you will end up with something like this config. I took out everything but the Firewall, Interfaces, and zone-policy sections. It is long enough as is.
+== IPv6 Tunnel ==
+
+If you are using a IPv6 tunnel from HE.net or someone else, the basis is the same except you have two WAN interface. One for v4 and one for v6.
+
+You would have 5 zones instead of just 4 and you would configure your v6 ruleset between your tunnel interface and your LAN/DMZ zones instead of to the WAN.
+
+LAN, WAN, DMZ, local and TUN (tunnel)
+
+v6 pairs would be:
+
+.. code-block:: sh
+
+  lan-tun
+  lan-local
+  lan-dmz
+  tun-lan
+  tun-local
+  tun-dmz
+  local-lan
+  local-tun
+  local-dmz
+  dmz-lan
+  dmz-tun
+  dmz-local
+
+Notice, none go to WAN since WAN wouldn't have a v6 address on it.
+
+You would have to add a couple of rules on your wan-local ruleset to allow protocol 41 in.
+
+Something like:
+
+.. code-block:: sh
+
+  rule 400 {
+    action accept
+    destination {
+      address 172.16.10.1
+    }
+    log enable
+    protocol 41
+    source {
+      address ip.of.tunnel.broker
+    }
+  }
+