Merge branch 'master' into newdirectives

1 files changed, 223 insertions, 69 deletions

diff --git a/docs/interfaces/ethernet.rst b/docs/interfaces/ethernet.rst
index a8cee8c2..1f691269 100644
--- a/docs/interfaces/ethernet.rst
+++ b/docs/interfaces/ethernet.rst
@@ -1,72 +1,226 @@
 .. _ethernet-interface:
 
+########
 Ethernet
---------
-
-Ethernet interfaces allow for the configuration of speed, duplex, and hw-id
-(MAC address). Below is an example configuration:
-
-.. code-block:: none
-
-  set interfaces ethernet eth1 address '192.168.0.1/24'
-  set interfaces ethernet eth1 address '2001:db8:1::ffff/64'
-  set interfaces ethernet eth1 description 'INSIDE'
-  set interfaces ethernet eth1 duplex 'auto'
-  set interfaces ethernet eth1 speed 'auto'
-
-Resulting in:
-
-.. code-block:: none
-
-  ethernet eth1 {
-      address 192.168.0.1/24
-      address 2001:db8:1::ffff/64
-      description INSIDE
-      duplex auto
-      hw-id 00:53:29:44:3b:19
-      smp_affinity auto
-      speed auto
-  }
-
-In addition, Ethernet interfaces provide the extended operational commands:
-
-* ``show interfaces ethernet <name> physical``
-* ``show interfaces ethernet <name> statistics``
-
-Statistics available are driver dependent.
-
-.. code-block:: none
-
-  vyos@vyos:~$ show interfaces ethernet eth0 physical
-  Settings for eth0:
-          Supported ports: [ TP ]
-          Supported link modes:   10baseT/Half 10baseT/Full
-                                  100baseT/Half 100baseT/Full
-                                  1000baseT/Full
-          Supports auto-negotiation: Yes
-          Advertised link modes:  10baseT/Half 10baseT/Full
-                                  100baseT/Half 100baseT/Full
-                                  1000baseT/Full
-          Advertised pause frame use: No
-          Advertised auto-negotiation: Yes
-          Speed: 1000Mb/s
-          Duplex: Full
-          Port: Twisted Pair
-          PHYAD: 0
-          Transceiver: internal
-          Auto-negotiation: on
-          MDI-X: Unknown
-          Supports Wake-on: d
-          Wake-on: d
-          Current message level: 0x00000007 (7)
-          Link detected: yes
-  driver: e1000
-  version: 7.3.21-k8-NAPI
-  firmware-version:
-  bus-info: 0000:02:01.0
-
-  vyos@vyos:~$ show interfaces ethernet eth0 statistics
-  NIC statistics:
-       rx_packets: 3530
-       tx_packets: 2179
-  [...]
+########
+
+Configuration
+#############
+
+Address
+-------
+
+.. cfgcmd:: set interfaces ethernet <interface> address <address | dhcp | dhcpv6>
+
+   Configure interface `<interface>` with one or more interface addresses.
+
+   * **address** can be specified multiple times as IPv4 and/or IPv6 address,
+     e.g. 192.0.2.1/24 and/or 2001:db8::1/64
+   * **dhcp** interface address is received by DHCP from a DHCP server on this
+     segment.
+   * **dhcpv6** interface address is received by DHCPv6 from a DHCPv6 server on
+     this segment.
+
+   Example:
+
+   .. code-block:: none
+
+     set interfaces ethernet eth0 address 192.0.2.1/24
+     set interfaces ethernet eth0 address 192.0.2.2/24
+     set interfaces ethernet eth0 address 2001:db8::ffff/64
+     set interfaces ethernet eth0 address 2001:db8:100::ffff/64
+
+.. cfgcmd:: set interfaces ethernet <interface> ipv6 address autoconf
+
+   .. include:: common-ipv6-addr-autoconf.txt
+
+.. cfgcmd:: set interfaces ethernet <interface> ipv6 address eui64 <prefix>
+
+   :abbr:`EUI-64 (64-Bit Extended Unique Identifier)` as specified in
+   :rfc:`4291` allows a host to assign iteslf a unique 64-Bit IPv6 address.
+
+   .. code-block:: none
+
+     set interfaces ethernet eth0 ipv6 address eui64 2001:db8:beef::/64
+
+Speed/Duplex
+------------
+
+.. cfgcmd:: set interfaces ethernet <interface> duplex <auto | full | half>
+
+   Configure physical interface duplex setting.
+
+   * auto - interface duplex setting is auto-negotiated
+   * full - always use full-duplex
+   * half - always use half-duplex
+
+   VyOS default will be `auto`.
+
+.. cfgcmd:: set interfaces ethernet <interface> speed <auto | 10 | 100 | 1000 | 2500 | 5000 | 10000 | 25000 | 40000 | 50000 | 100000>
+
+   Configure physical interface speed setting.
+
+   * auto - interface speed is auto-negotiated
+   * 10 - 10 MBit/s
+   * 100 - 100 MBit/s
+   * 1000 - 1 GBit/s
+   * 2500 - 2.5 GBit/s
+   * 5000 - 5 GBit/s
+   * 10000 - 10 GBit/s
+   * 25000 - 25 GBit/s
+   * 40000 - 40 GBit/s
+   * 50000 - 50 GBit/s
+   * 100000 - 100 GBit/s
+
+   VyOS default will be `auto`.
+
+Link Administration
+-------------------
+
+.. cfgcmd:: set interfaces ethernet <interface> description <description>
+
+   Assign given `<description>` to interface. Description will also be passed
+   to SNMP monitoring systems.
+
+.. cfgcmd:: set interfaces ethernet <interface> disable
+
+   Disable given `<interface>`. It will be placed in administratively down
+   (``A/D``) state.
+
+.. cfgcmd:: set interfaces ethernet <interface> disable-flow-control
+
+   Disable Ethernet flow control (pause frames).
+
+
+.. cfgcmd:: set interfaces ethernet <interface> mac <mac-address>
+
+   Configure user defined :abbr:`MAC (Media Access Control)` address on given
+   `<interface>`.
+
+.. cfgcmd:: set interfaces ethernet <interface> mtu <mtu>
+
+   Configure :abbr:`MTU (Maximum Transmission Unit)` on given `<interface>`. It
+   is the size (in bytes) of the largest ethernet frame sent on this link.
+
+Router Advertisements
+---------------------
+
+Router advertisements are described in :rfc:`4861#section-4.6.2`. They are part
+of what is known as :abbr:`SLAAC (Stateless Address Autoconfiguration)`.
+
+.. cfgcmd:: set interfaces ethernet <interface> ipv6 router-advert send-advert <true | false>
+
+   Enable or disable router advertisements in this `<interface>`.
+
+.. cfgcmd:: set interfaces ethernet <interface> ipv6 router-advert prefix <prefix>
+
+   Prefix information is described in :rfc:`4861#section-4.6.2`.
+
+Operation
+=========
+
+.. opcmd:: show interfaces ethernet
+
+   Show brief interface information.
+
+   .. code-block:: none
+
+     vyos@vyos:~$ show interfaces ethernet
+     Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
+     Interface        IP Address                        S/L  Description
+     ---------        ----------                        ---  -----------
+     eth0             172.18.201.10/24                  u/u  LAN
+     eth1             172.18.202.11/24                  u/u  WAN
+     eth2             -                                 u/D
+
+.. opcmd:: show interfaces ethernet <interface>
+
+   Show detailed information on given `<interface>`
+
+   .. code-block:: none
+
+     vyos@vyos:~$ show interfaces ethernet eth0
+     eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
+         link/ether 00:50:44:00:f5:c9 brd ff:ff:ff:ff:ff:ff
+         inet6 fe80::250:44ff:fe00:f5c9/64 scope link
+            valid_lft forever preferred_lft forever
+
+         RX:  bytes    packets     errors    dropped    overrun      mcast
+           56735451     179841          0          0          0     142380
+         TX:  bytes    packets     errors    dropped    carrier collisions
+            5601460      62595          0          0          0          0
+
+.. opcmd:: show interfaces ethernet <interface> physical
+
+   Show information about physical `<interface>`
+
+   .. code-block:: none
+
+     vyos@vyos:~$ show interfaces ethernet eth0 physical
+     Settings for eth0:
+             Supported ports: [ TP ]
+             Supported link modes:   1000baseT/Full
+                                     10000baseT/Full
+             Supported pause frame use: No
+             Supports auto-negotiation: No
+             Supported FEC modes: Not reported
+             Advertised link modes:  Not reported
+             Advertised pause frame use: No
+             Advertised auto-negotiation: No
+             Advertised FEC modes: Not reported
+             Speed: 10000Mb/s
+             Duplex: Full
+             Port: Twisted Pair
+             PHYAD: 0
+             Transceiver: internal
+             Auto-negotiation: off
+             MDI-X: Unknown
+             Supports Wake-on: uag
+             Wake-on: d
+             Link detected: yes
+     driver: vmxnet3
+     version: 1.4.16.0-k-NAPI
+     firmware-version:
+     expansion-rom-version:
+     bus-info: 0000:0b:00.0
+     supports-statistics: yes
+     supports-test: no
+     supports-eeprom-access: no
+     supports-register-dump: yes
+     supports-priv-flags: no
+
+.. opcmd:: show interfaces ethernet <interface> transceiver
+
+   Show transceiver information from plugin modules, e.g SFP+, QSFP
+
+   .. code-block:: none
+
+     vyos@vyos:~$ show interfaces ethernet eth5 transceiver
+        Identifier              : 0x03 (SFP)
+        Extended identifier     : 0x04 (GBIC/SFP defined by 2-wire interface ID)
+        Connector               : 0x07 (LC)
+        Transceiver codes       : 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00 0x00
+        Transceiver type        : Ethernet: 1000BASE-SX
+        Encoding                : 0x01 (8B/10B)
+        BR, Nominal             : 1300MBd
+        Rate identifier         : 0x00 (unspecified)
+        Length (SMF,km)         : 0km
+        Length (SMF)            : 0m
+        Length (50um)           : 550m
+        Length (62.5um)         : 270m
+        Length (Copper)         : 0m
+        Length (OM3)            : 0m
+        Laser wavelength        : 850nm
+        Vendor name             : CISCO-FINISAR
+        Vendor OUI              : 00:90:65
+        Vendor PN               : FTRJ-8519-7D-CS4
+        Vendor rev              : A
+        Option values           : 0x00 0x1a
+        Option                  : RX_LOS implemented
+        Option                  : TX_FAULT implemented
+        Option                  : TX_DISABLE implemented
+        BR margin, max          : 0%
+        BR margin, min          : 0%
+        Vendor SN               : FNS092xxxxx
+        Date code               : 0506xx
+