Migrate new file structure to crux (#435)

* order workflows and add submodule

* rename gitmodules file

* delete docs/.gitignore

* add vyos custom linter

* correct __pycache__ in gitignore

* add test-coverage.py

* move draw.io folder

* arrange changelog, install history and about

* arrange: firewall

* arrange: highavailability

* arrange: loadbalancing

* arrange: nat

* arrange: services

* sort configexamples and configuration interfaces

* wireles: rename wireless

* rearrange: Protocols and Policy

* rearrange: Firewall and Zone Policy

* rearrange: Interfaces

* rearrange: Interfaces

* rearrange: dynamic DNS

* hostinfo: add page to index

* rearrange: appendix

* venv: add Pipfile

* rearrange: contributing

* index: remove debugging

* rearrange: fix all figure and refs

* rearrange: commandtree

* fix: cli, openvpn, install headline level

* protocols: change headline

* firewall: move mss clamping

* ip: separate ipv4 and ipv6

* arp: move to static page

* igmp: rename multicast page

* Update to year 2021

1 files changed, 0 insertions, 82 deletions

diff --git a/docs/interfaces/pppoe.rst b/docs/interfaces/pppoe.rst
deleted file mode 100644
index d8625722..00000000
--- a/docs/interfaces/pppoe.rst
+++ /dev/null
@@ -1,82 +0,0 @@
-.. _pppoe:
-
-
-PPPoE
-=====
-
-There are two main ways to setup VyOS to connect over a PPPoE internet connection. This is due to most ISPs (Internet Service Providers) providing a DSL modem that is also a wireless router.
-
-**First Method:** (Common for Homes)
-
-In this method, the DSL Modem/Router connects to the ISP for you with your credentials preprogrammed into the device.  This gives you an RFC1918_ address, such as 192.168.1.0/24 by default.
-
-For a simple home network using just the ISP's equipment, this is usually desirable.  But if you want to run VyOS as your firewall and router, this will result in having a double NAT and firewall setup. This results in a few extra layers of complexity, particularly if you use some NAT or tunnel features.
-
-**Second Method:** (Common for Businesses)
-
-In order to have full control and make use of multiple static public IP addresses, your VyOS will have to initiate the PPPoE connection and control it.
-In order for this method to work, you will have to figure out how to make your DSL Modem/Router switch into a Bridged Mode so it only acts as a DSL Transceiver device to connect between the Ethernet link of your VyOS and the phone cable.
-Once your DSL Transceiver is in Bridge Mode, you should get no IP address from it.
-Please make sure you connect to the Ethernet Port 1 if your DSL Transeiver has a switch, as some of them only work this way.
-Once you have an Ethernet device connected, i.e. eth0, then you can configure it to open the PPPoE session for you and your DSL Transceiver (Modem/Router) just acts to translate your messages in a way that vDSL/aDSL understands.
-
-**Here is an example configuration:**
-
-.. code-block:: none
-
-  set interface ethernet eth0 description "DSL Modem"
-  set interface ethernet eth0 duplex auto
-  set interface ethernet eth0 smp_affinity auto
-  set interface ethernet eth0 speed auto
-  set interface ethernet eth0 pppoe 0 default-route auto
-  set interface ethernet eth0 pppoe 0 mtu 1492
-  set interface ethernet eth0 pppoe 0 name-server auto
-  set interface ethernet eth0 pppoe 0 user-id <PPPoE Username>
-  set interface ethernet eth0 pppoe 0 password <PPPoE Password>
-
-
-* You should add a firewall to your configuration above as well by assigning it to the pppoe0 itself as shown here:
-
-.. code-block:: none
-
-  set interface ethernet eth0 pppoe 0 firewall in name NET-IN
-  set interface ethernet eth0 pppoe 0 firewall local name NET-LOCAL
-  set interface ethernet eth0 pppoe 0 firewall out name NET-OUT
-
-* You need your PPPoE credentials from your DSL ISP in order to configure this. The usual username is in the form of name@host.net but may vary depending on ISP.
-* The largest MTU size you can use with DSL is 1492 due to PPPoE overhead. If you are switching from a DHCP based ISP like cable then be aware that things like VPN links may need to have their MTU sizes adjusted to work within this limit.
-* With the ``default-route`` option set to ``auto``, VyOS will only add the Default Gateway you receive from your DSL ISP to the routing table if you have no other WAN connections. If you wish to use a Dual WAN connection, change the ``default-route`` option to ``force``.
-
-Handling and troubleshooting
-----------------------------
-
-You can test connecting and disconnecting with the below commands:
-
-.. code-block:: none
-
-  disconnect interface 0
-  connect interface 0
-
-
-You can check the PPPoE connection logs with the following:
-
-This command shows the current statistics, status and some of the settings (i.e. MTU) for the current connection on pppoe0.
-
-.. code-block:: none
-
-  show interfaces pppoe 0
-
-This command shows the entire log for the PPPoE connection starting with the oldest data. Scroll down with the <space> key to reach the end where the current data is.
-
-.. code-block:: none
-
-  show interfaces pppoe 0 log
-
-
-This command shows the same log as without the 'tail' option but only starts with the last few lines and continues to show added lines until you exit with ``Ctrl + x``
-
-.. code-block:: none
-
-  show interfaces pppoe 0 log tail
-
-.. _RFC1918: https://tools.ietf.org/html/rfc1918