Split network-interfaces into multiple files

- Now sections as separate files under interfaces/
- Fixed some references

1 files changed, 0 insertions, 807 deletions

diff --git a/docs/network-interfaces.rst b/docs/network-interfaces.rst
deleted file mode 100644
index 0214ee1e..00000000
--- a/docs/network-interfaces.rst
+++ /dev/null
@@ -1,807 +0,0 @@
-.. _network-interfaces:
-
-Network Interfaces
-==================
-
-Configured interfaces on a VyOS system can be displayed using the `show
-interfaces` command.
-
-.. code-block:: sh
-
-  vyos@vyos:~$ show interfaces
-  Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
-  Interface        IP Address                        S/L  Description
-  ---------        ----------                        ---  -----------
-  eth0             172.16.51.129/24                  u/u  OUTSIDE
-  eth1             192.168.0.1/24                    u/u  INSIDE
-  lo               127.0.0.1/8                       u/u
-                   ::1/128
-  vyos@vyos:~$
-
-A specific interface can be shown using the `show interfaces <type> <name>`
-command.
-
-.. code-block:: sh
-
-  vyos@vyos:~$ show interfaces ethernet eth0
-  eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000
-      link/ether 00:0c:29:44:3b:0f brd ff:ff:ff:ff:ff:ff
-      inet 172.16.51.129/24 brd 172.16.51.255 scope global eth0
-      inet6 fe80::20c:29ff:fe44:3b0f/64 scope link
-         valid_lft forever preferred_lft forever
-      Description: OUTSIDE
-
-      RX:  bytes    packets     errors    dropped    overrun      mcast
-          274397       3064          0          0          0          0
-      TX:  bytes    packets     errors    dropped    carrier collisions
-          257276       1890          0          0          0          0
-  vyos@vyos:~$
-
-Different network interfaces provide type-specific configuration. Ethernet
-interfaces, for example, allow the configuration of speed and duplex.
-
-Many services, such as network routing, firewall, and traffic policy also
-maintain interface-specific configuration. These will be covered in their
-respective sections.
-
-Interface Addresses
--------------------
-
-Each interface can be configured with a description and address. Interface
-addresses might be:
-
-* Static IPv4 `address 172.16.51.129/24`
-* Static IPv6 `address 2001:db8:1::ffff/64`
-* DHCP IPv4 `address dhcp`
-* DHCP IPv6 `address dhcpv6`
-
-An interface description is assigned using the following command:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth0 description 'OUTSIDE'
-
-IPv4
-^^^^
-
-Static Address
-**************
-
-This method is supported on all interfaces, apart from OpenVPN that uses
-different syntax and wireless modems that are always autoconfigured through
-PPP.
-
-The command is `set interfaces $type $name address $address`. Examples:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth0 address 192.0.2.1/24
-  set interfaces tunnel tun0 address 10.0.0.1/30
-  set interfaces bridge br0 address 203.0.113.45/26
-  set interfaces ethernet eth0 vif 30 address 192.0.30.254/24
-
-DHCP
-****
-
-This method is supported on all physical interfaces, and those that are
-directly connected to a physical interface (ethernet, VLAN, bridge, bond,
-pseudo-ethernet, wireless).
-
-The command is `set interfaces $type $name address dhcp`. Examples:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth0 vif 90 address dhcp
-  set interfaces bridge br0 address dhcp
-
-IPv6
-^^^^
-
-Static Address
-**************
-
-This method is supported on all interfaces, apart from OpenVPN that uses
-different syntax and wireless modems that are always autoconfigured through
-PPP. Static IPv6 addresses are supported on all interfaces except VTI.
-
-The command is `set interfaces $type $name address $address`. Examples:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth0 address 2001:db8:100::ffff/64
-  set interfaces tunnel tun0 address 2001:db8::1/64
-  set interfaces bridge br0 address  2001:db8:200::1/64
-  set interfaces ethernet eth0 vif 30 address 2001:db8:3::ffff/64
-
-DHCP
-****
-
-This method is supported on all physical interfaces, and those that are
-directly connected to a physical interface (ethernet, VLAN, bridge, bond,
-pseudo-ethernet, wireless).
-
-The command is `set interfaces $type $name address dhcpv6`. Examples:
-
-.. code-block:: sh
-
-  set interfaces bonding bond1 address dhcpv6
-  set interfaces bridge br0 vif 56 address dhcpv6
-
-Autoconfiguration (SLAAC)
-*************************
-
-SLAAC is specified in RFC4862_. This method is supported on all physical
-interfaces, and those that are directly connected to a physical interface
-(ethernet, VLAN, bridge, bond, pseudo-ethernet, wireless).
-
-The command is `set interfaces $type $name ipv6 address autoconf`. Examples:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth0 vif 90 ipv6 address autoconf
-  set interfaces bridge br0 ipv6 address autoconf
-
-.. note:: This method automatically disables IPv6 traffic forwarding on the
-   interface in question.
-
-EUI-64
-******
-
-EUI-64 (64-Bit Extended Unique Identifier) as specified in RFC4291_. IPv6
-addresses in /64 networks can be automatically generated from the prefix and
-MAC address, if you specify the prefix.
-
-The command is `set interfaces $type $name ipv6 address eui64 $prefix`. Examples:
-
-.. code-block:: sh
-
-  set interfaces bridge br0 ipv6 address eui64 2001:db8:beef::/64
-  set interfaces pseudo-ethernet peth0 ipv6 address eui64 2001:db8:aa::/64
-
-Ethernet Interfaces
--------------------
-
-Ethernet interfaces allow for the configuration of speed, duplex, and hw-id
-(MAC address). Below is an example configuration:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth1 address '192.168.0.1/24'
-  set interfaces ethernet eth1 address '2001:db8:1::ffff/64'
-  set interfaces ethernet eth1 description 'INSIDE'
-  set interfaces ethernet eth1 duplex 'auto'
-  set interfaces ethernet eth1 speed 'auto'
-
-Resulting in:
-
-.. code-block:: sh
-
-  ethernet eth1 {
-      address 192.168.0.1/24
-      address 2001:db8:1::ffff/64
-      description INSIDE
-      duplex auto
-      hw-id 00:0c:29:44:3b:19
-      smp_affinity auto
-      speed auto
-  }
-
-In addition, Ethernet interfaces provide the extended operational commands
-`show interfaces ethernet <name> physical` and `show interfaces ethernet <name>
-statistics`. Statistics available are driver dependent.
-
-.. code-block:: sh
-
-  vyos@vyos:~$ show interfaces ethernet eth0 physical
-  Settings for eth0:
-          Supported ports: [ TP ]
-          Supported link modes:   10baseT/Half 10baseT/Full
-                                  100baseT/Half 100baseT/Full
-                                  1000baseT/Full
-          Supports auto-negotiation: Yes
-          Advertised link modes:  10baseT/Half 10baseT/Full
-                                  100baseT/Half 100baseT/Full
-                                  1000baseT/Full
-          Advertised pause frame use: No
-          Advertised auto-negotiation: Yes
-          Speed: 1000Mb/s
-          Duplex: Full
-          Port: Twisted Pair
-          PHYAD: 0
-          Transceiver: internal
-          Auto-negotiation: on
-          MDI-X: Unknown
-          Supports Wake-on: d
-          Wake-on: d
-          Current message level: 0x00000007 (7)
-          Link detected: yes
-  driver: e1000
-  version: 7.3.21-k8-NAPI
-  firmware-version:
-  bus-info: 0000:02:01.0
-
-  vyos@vyos:~$ show interfaces ethernet eth0 statistics
-  NIC statistics:
-       rx_packets: 3530
-       tx_packets: 2179
-  [...]
-
-Wireless Interfaces
--------------------
-Wireless, for example WiFi 802.11 b/g/n, interfaces allow for connection to
-WiFi networks or act as an access-point.
-If your device is configurable it will appear as `wlan` in `show interfaces`.
-
-To be able to use the wireless interfaces you will first need to set a
-regulatory domain with the country code of your locaion.
-
-.. code-block:: sh
-
-  set system wifi-regulatory-domain SE
-
-An example on how to set it up as an access point:
-
-.. code-block:: sh
-
-  set interfaces wireless wlan0 address '192.168.99.1/24'
-  set interfaces wireless wlan0 type access-point
-  set interfaces wireless wlan0 channel 1
-  set interfaces wireless wlan0 ssid '<your ssid>'
-  set interfaces wireless wlan0 security wpa mode wpa2
-  set interfaces wireless wlan0 security wpa cipher CCMP
-  set interfaces wireless wlan0 security wpa passphrase '<your passphrase>'
-
-Resulting in
-
-.. code-block:: sh
-
-  interfaces {
-    [...]
-    wireless wlan0 {
-          address 192.168.99.1/24
-          channel 1
-          mode g
-          security {
-              wpa {
-                  cipher CCMP
-                  mode wpa2
-                  passphrase "<your passphrase>"
-              }
-          }
-          ssid "<your ssid>"
-          type access-point
-      }
-  }
-  system {
-    [...]
-    wifi-regulatory-domain SE
-  }
-
-To get it to work as a access point with this configuration you will need
-to set up a DHCP server to work with that network.
-
-
-VLAN Sub-Interfaces (802.1Q)
-----------------------------
-
-802.1Q VLAN interfaces are represented as virtual sub-interfaces in VyOS. The
-term used for this is `vif`. Configuration of a tagged sub-interface is
-accomplished using the configuration command `set interfaces ethernet <name>
-vif <vlan-id>`.
-
-.. code-block:: sh
-
-  set interfaces ethernet eth1 vif 100 description 'VLAN 100'
-  set interfaces ethernet eth1 vif 100 address '192.168.100.1/24'
-  set interfaces ethernet eth1 vif 100 address '2001:db8:100::1/64'
-
-Resulting in:
-
-.. code-block:: sh
-
-  ethernet eth1 {
-      address 192.168.100.1/24
-      address 2001:db8:100::1/64
-      description INSIDE
-      duplex auto
-      hw-id 00:0c:29:44:3b:19
-      smp_affinity auto
-      speed auto
-      vif 100 {
-          address 192.168.100.1/24
-          description "VLAN 100"
-      }
-  }
-
-VLAN interfaces are shown as `<name>.<vlan-id>`, e.g. `eth1.100`:
-
-.. code-block:: sh
-
-  vyos@vyos:~$ show interfaces
-  Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
-  Interface        IP Address                        S/L  Description
-  ---------        ----------                        ---  -----------
-  eth0             172.16.51.129/24                  u/u  OUTSIDE
-  eth1             192.168.0.1/24                    u/u  INSIDE
-  eth1.100         192.168.100.1/24                  u/u  VLAN 100
-  lo               127.0.0.1/8                       u/u
-                   ::1/128
-
-Bridging
---------
-
-Interfaces in VyOS can be bridged together to provide software switching of
-Layer-2 traffic.
-
-A bridge is created when a bridge interface is defined. In the example below
-we will be creating a bridge for VLAN 100 and assigning a VIF to the bridge.
-
-.. code-block:: sh
-
-  set interfaces bridge 'br100'
-  set interfaces ethernet eth1 vif 100 bridge-group bridge br100
-
-Interfaces assigned to a bridge-group do not have address configuration. An IP
-address can be assigned to the bridge interface itself, however, like any
-normal interface.
-
-.. code-block:: sh
-
-  set interfaces bridge br100 address '192.168.100.1/24'
-  set interfaces bridge br100 address '2001:db8:100::1/64'
-
-Example Result:
-
-.. code-block:: sh
-
-  bridge br100 {
-      address 192.168.100.1/24
-      address 2001:db8:100::1/64
-  }
-  [...]
-  ethernet eth1 {
-  [...]
-      vif 100 {
-          bridge-group {
-              bridge br100
-          }
-      }
-  }
-
-In addition to normal IP interface configuration, bridge interfaces support
-Spanning-Tree Protocol. STP is disabled by default.
-
-.. note:: Please use caution when introducing spanning-tree protocol on a
-   network as it may result in topology changes.
-
-To enable spanning-tree use the `set interfaces bridge <name> stp true` command:
-
-.. code-block:: sh
-
-  set interfaces bridge br100 stp true
-
-STP `priority`, `forwarding-delay`, `hello-time`, and `max-age` can be
-configured for the bridge-group. The MAC aging time can also be configured
-using the `aging` directive.
-
-For member interfaces, the bridge-group `priority` and `cost` can be configured.
-
-The `show bridge` operational command can be used to display configured bridges:
-
-.. code-block:: sh
-
-  vyos@vyos:~$ show bridge
-  bridge name     bridge id               STP enabled     interfaces
-  br100           0000.000c29443b19       yes             eth1.100
-
-If spanning-tree is enabled, the `show bridge <name> spanning-tree` command
-can be used to show STP configuration:
-
-.. code-block:: sh
-
-  vyos@vyos:~$ show bridge br100 spanning-tree
-  br100
-   bridge id              0000.000c29443b19
-   designated root        0000.000c29443b19
-   root port                 0                    path cost                  0
-   max age                  20.00                 bridge max age            20.00
-   hello time                2.00                 bridge hello time          2.00
-   forward delay            15.00                 bridge forward delay      15.00
-   ageing time             300.00
-   hello timer               0.47                 tcn timer                  0.00
-   topology change timer     0.00                 gc timer                  64.63
-   flags
-
-  eth1.100 (1)
-   port id                8001                    state                forwarding
-   designated root        0000.000c29443b19       path cost                  4
-   designated bridge      0000.000c29443b19       message age timer          0.00
-   designated port        8001                    forward delay timer        0.00
-   designated cost           0                    hold timer                 0.00
-   flags
-
-The MAC address-table for a bridge can be displayed using the `show bridge
-<name> macs` command:
-
-.. code-block:: sh
-
-  vyos@vyos:~$ show bridge br100 macs
-  port no mac addr                is local?       ageing timer
-    1     00:0c:29:44:3b:19       yes                0.00
-
-Bonding
--------
-
-You can combine (aggregate) 2 or more physical interfaces into a single
-logical one. It's called bonding, or LAG, or ether-channel, or port-channel.
-
-Create interface bondX, where X is just a number:
-
-.. code-block:: sh
-
-  set interfaces bonding bond0 description 'my-sw1 int 23 and 24'
-
-You are able to choose a hash policy:
-
-.. code-block:: sh
-
-  vyos@vyos# set interfaces bonding bond0 hash-policy
-  Possible completions:
-    layer2       use MAC addresses to generate the hash (802.3ad)
-    layer2+3     combine MAC address and IP address to make hash
-    layer3+4     combine IP address and port to make hash
-
-For example:
-
-.. code-block:: sh
-
-  set interfaces bonding bond0 hash-policy 'layer2'
-
-You may want to set IEEE 802.3ad Dynamic link aggregation (802.3ad) AKA LACP
-(don't forget to setup it on the other end of these links):
-
-.. code-block:: sh
-
- set interfaces bonding bond0 mode '802.3ad'
-
-or some other modes:
-
-.. code-block:: sh
-
-  vyos@vyos# set interfaces bonding bond0 mode
-  Possible completions:
-    802.3ad      IEEE 802.3ad Dynamic link aggregation (Default)
-    active-backup
-                 Fault tolerant: only one slave in the bond is active
-    broadcast    Fault tolerant: transmits everything on all slave interfaces
-    round-robin  Load balance: transmit packets in sequential order
-    transmit-load-balance
-                 Load balance: adapts based on transmit load and speed
-    adaptive-load-balance
-                 Load balance: adapts based on transmit and receive plus ARP
-    xor-hash     Load balance: distribute based on MAC address
-
-Now bond some physical interfaces into bond0:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth0 bond-group 'bond0'
-  set interfaces ethernet eth0 description 'member of bond0'
-  set interfaces ethernet eth1 bond-group 'bond0'
-  set interfaces ethernet eth1 description 'member of bond0'
-
-After a commit you may treat bond0 as almost a physical interface (you can't
-change its` duplex, for example) and assign IPs or VIFs on it.
-
-You may check the result:
-
-.. code-block:: sh
-
-  vyos@vyos# run sh interfaces bonding
-  Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
-  Interface        IP Address                        S/L  Description
-  ---------        ----------                        ---  -----------
-  bond0            -                                 u/u  my-sw1 int 23 and 24
-  bond0.10         192.168.0.1/24                    u/u  office-net
-  bond0.100        10.10.10.1/24                     u/u  management-net
-
-Tunnel Interfaces
------------------
-
-Set Virtual Tunnel interface
-
-.. code-block:: sh
-
-  set interfaces vti vti0 address 192.168.2.249/30
-  set interfaces vti vti0 address 2001:db8:2::249/64
-
-Results in:
-
-.. code-block:: sh
-
-  vyos@vyos# show interfaces vti
-  vti vti0 {
-      address 192.168.2.249/30
-      address 2001:db8:2::249/64
-      description "Description"
-  }
-
-VXLAN
------
-
-VXLAN is an overlaying Ethernet over IP protocol. It is described in RFC7348_.
-
-If configuring VXLAN in a VyOS virtual machine, ensure that MAC spoofing
-(Hyper-V) or Forged Transmits (ESX) are permitted, otherwise forwarded frames
-may be blocked by the hypervisor.
-
-Multicast VXLAN
-^^^^^^^^^^^^^^^^
-
-Example Topology:
-
-PC4 - Leaf2 - Spine1 - Leaf3 - PC5
-
-PC4 has IP 10.0.0.4/24 and PC5 has IP 10.0.0.5/24, so they believe they are in
-the same broadcast domain.
-
-Let's assume PC4 on Leaf2 wants to ping PC5 on Leaf3. Instead of setting Leaf3
-as our remote end manually, Leaf2 encapsulates the packet into a UDP-packet and
-sends it to its designated multicast-address via Spine1. When Spine1 receives
-this packet it forwards it to all other Leafs who has joined the same
-multicast-group, in this case Leaf3. When Leaf3 receives the packet it forwards
-it, while at the same time learning that PC4 is reachable behind Leaf2, because
-the encapsulated packet had Leaf2's IP-address set as source IP.
-
-PC5 receives the ping echo, responds with an echo reply that Leaf3 receives and
-this time forwards to Leaf2's unicast address directly because it learned the
-location of PC4 above. When Leaf2 receives the echo reply from PC5 it sees that
-it came from Leaf3 and so remembers that PC5 is reachable via Leaf3.
-
-Thanks to this discovery, any subsequent traffic between PC4 and PC5 will not
-be using the multicast-address between the Leafs as they both know behind which
-Leaf the PCs are connected. This saves traffic as less multicast packets sent
-reduces the load on the network, which improves scalability when more Leafs are
-added.
-
-For optimal scalability Multicast shouldn't be used at all, but instead use BGP
-to signal all connected devices between leafs. Unfortunately, VyOS does not yet
-support this.
-
-Configuration commands
-^^^^^^^^^^^^^^^^^^^^^^
-
-.. code-block:: sh
-
-  interfaces
-    vxlan <vxlan[0-16777215]>
-      address          # IP address of the VXLAN interface
-      bridge-group     # Configure a L2 bridge-group
-      description      # Description
-      group <ipv4>     # IPv4 Multicast group address (required)
-      ip               # IPv4 routing options
-      ipv6             # IPv6 routing options
-      link <dev>       # IP interface for underlay of this vxlan overlay (optional)
-      mtu              # MTU
-      policy           # Policy routing options
-      remote           # Remote address of the VXLAN tunnel, used for PTP instead of multicast
-      vni <1-16777215> # Virtual Network Identifier (required)
-
-Configuration Example
-^^^^^^^^^^^^^^^^^^^^^
-
-The setup is this:
-
-Leaf2 - Spine1 - Leaf3
-
-Spine1 is a Cisco IOS router running version 15.4, Leaf2 and Leaf3 is each a
-VyOS router running 1.2.
-
-This topology was built using GNS3.
-
-Topology:
-
-.. code-block:: sh
-
-  Spine1:
-  fa0/2 towards Leaf2, IP-address: 10.1.2.1/24
-  fa0/3 towards Leaf3, IP-address: 10.1.3.1/24
-
-  Leaf2:
-  Eth0 towards Spine1, IP-address: 10.1.2.2/24
-  Eth1 towards a vlan-aware switch
-
-  Leaf3:
-  Eth0 towards Spine1, IP-address 10.1.3.3/24
-  Eth1 towards a vlan-aware switch
-
-Spine1 Configuration:
-
-.. code-block:: sh
-
-  conf t
-  ip multicast-routing
-  !
-  interface fastethernet0/2
-   ip address 10.1.2.1 255.255.255.0
-   ip pim sparse-dense-mode
-  !
-  interface fastethernet0/3
-   ip address 10.1.3.1 255.255.255.0
-   ip pim sparse-dense-mode
-  !
-  router ospf 1
-   network 10.0.0.0 0.255.255.255 area 0
-
-Multicast-routing is required for the leafs to forward traffic between each
-other in a more scalable way. This also requires PIM to be enabled towards the
-Leafs so that the Spine can learn what multicast groups each Leaf expect traffic
-from.
-
-Leaf2 configuration:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth0 address '10.1.2.2/24'
-  set protocols ospf area 0 network '10.0.0.0/8'
-
-  ! Our first vxlan interface
-  set interfaces bridge br241 address '172.16.241.1/24'
-  set interfaces ethernet eth1 vif 241 bridge-group bridge 'br241'
-  set interfaces vxlan vxlan241 bridge-group bridge 'br241'
-  set interfaces vxlan vxlan241 group '239.0.0.241'
-  set interfaces vxlan vxlan241 link 'eth0'
-  set interfaces vxlan vxlan241 vni '241'
-
-  ! Our seconds vxlan interface
-  set interfaces bridge br242 address '172.16.242.1/24'
-  set interfaces ethernet eth1 vif 242 bridge-group bridge 'br242'
-  set interfaces vxlan vxlan242 bridge-group bridge 'br242'
-  set interfaces vxlan vxlan242 group '239.0.0.242'
-  set interfaces vxlan vxlan242 link 'eth0'
-  set interfaces vxlan vxlan242 vni '242'
-
-Leaf3 configuration:
-
-.. code-block:: sh
-
-  set interfaces ethernet eth0 address '10.1.3.3/24'
-  set protocols ospf area 0 network '10.0.0.0/8'
-
-  ! Our first vxlan interface
-  set interfaces bridge br241 address '172.16.241.1/24'
-  set interfaces ethernet eth1 vif 241 bridge-group bridge 'br241'
-  set interfaces vxlan vxlan241 bridge-group bridge 'br241'
-  set interfaces vxlan vxlan241 group '239.0.0.241'
-  set interfaces vxlan vxlan241 link 'eth0'
-  set interfaces vxlan vxlan241 vni '241'
-
-  ! Our seconds vxlan interface
-  set interfaces bridge br242 address '172.16.242.1/24'
-  set interfaces ethernet eth1 vif 242 bridge-group bridge 'br242'
-  set interfaces vxlan vxlan242 bridge-group bridge 'br242'
-  set interfaces vxlan vxlan242 group '239.0.0.242'
-  set interfaces vxlan vxlan242 link 'eth0'
-  set interfaces vxlan vxlan242 vni '242'
-
-As you can see, Leaf2 and Leaf3 configuration is almost identical. There are
-lots of commands above, I'll try to into more detail below, command
-descriptions are placed under the command boxes:
-
-.. code-block:: sh
-
-  set interfaces bridge br241 address '172.16.241.1/24'
-
-This commands creates a bridge that is used to bind traffic on eth1 vlan 241
-with the vxlan241-interface. The IP-address is not required. It may however be
-used as a default gateway for each Leaf which allows devices on the vlan to
-reach other subnets. This requires that the subnets are redistributed by OSPF
-so that the Spine will learn how to reach it. To do this you need to change the
-OSPF network from '10.0.0.0/8' to '0.0.0.0/0' to allow 172.16/12-networks to be
-advertised.
-
-.. code-block:: sh
-
-  set interfaces ethernet eth1 vif 241 bridge-group bridge 'br241'
-  set interfaces vxlan vxlan241 bridge-group bridge 'br241'
-
-Binds eth1 vif 241 and vxlan241 to each other by putting them in the same
-bridge-group. Internal VyOS requirement.
-
-.. code-block:: sh
-
-  set interfaces vxlan vxlan241 group '239.0.0.241'
-
-The multicast-group used by all Leafs for this vlan extension. Has to be the
-same on all Leafs that has this interface.
-
-.. code-block:: sh
-
-  set interfaces vxlan vxlan241 link 'eth0'
-
-Sets the interface to listen for multicast packets on. Could be a loopback, not
-yet tested.
-
-.. code-block:: sh
-
-  set interfaces vxlan vxlan241 vni '241'
-
-Sets the unique id for this vxlan-interface. Not sure how it correlates with
-multicast-address.
-
-.. code-block:: sh
-
-  set interfaces vxlan vxlan241 remote-port 12345
-
-The destination port used for creating a VXLAN interface in Linux defaults to
-its pre-standard value of 8472 to preserve backwards compatibility. A
-configuration directive to support a user-specified destination port to override
-that behavior is available using the above command.
-
-Older Examples
-^^^^^^^^^^^^^^
-
-Example for bridging normal L2 segment and vxlan overlay network, and using a
-vxlan interface as routing interface.
-
-.. code-block:: sh
-
-  interfaces {
-       bridge br0 {
-       }
-       ethernet eth0 {
-           address dhcp
-       }
-       loopback lo {
-       }
-       vxlan vxlan0 {
-           bridge-group {
-               bridge br0
-           }
-           group 239.0.0.1
-           vni 0
-       }
-       vxlan vxlan1 {
-           address 192.168.0.1/24
-           link eth0
-           group 239.0.0.1
-           vni 1
-       }
-  }
-
-Here is a working configuration that creates a VXLAN between two routers. Each
-router has a VLAN interface (26) facing the client devices and a VLAN interface
-(30) that connects it to the other routers. With this configuration, traffic
-can flow between both routers' VLAN 26, but can't escape since there is no L3
-gateway. You can add an IP to a bridge-group to create a gateway.
-
-.. code-block:: sh
-
-  interfaces {
-       bridge br0 {
-       }
-       ethernet eth0 {
-           duplex auto
-           smp-affinity auto
-           speed auto
-           vif 26 {
-               bridge-group {
-                   bridge br0
-               }
-           }
-           vif 30 {
-               address 10.7.50.6/24
-           }
-       }
-       loopback lo {
-       }
-       vxlan vxlan0 {
-           bridge-group {
-               bridge br0
-           }
-           group 239.0.0.241
-           vni 241
-       }
-  }
-
-.. include:: interfaces/wireguard.rst