Merge pull request #53 from rebortg/add/l2tpv3

 add L2TPv3 Interface

2 files changed, 120 insertions, 0 deletions

diff --git a/docs/interfaces/index.rst b/docs/interfaces/index.rst
index 8f648447..ff9e0e95 100644
--- a/docs/interfaces/index.rst
+++ b/docs/interfaces/index.rst
@@ -52,6 +52,7 @@ respective sections.
    addresses
    dummy
    ethernet
+   l2tpv3
    pppoe
    wireless
    bridging
diff --git a/docs/interfaces/l2tpv3.rst b/docs/interfaces/l2tpv3.rst
new file mode 100644
index 00000000..2238c970
--- /dev/null
+++ b/docs/interfaces/l2tpv3.rst
@@ -0,0 +1,119 @@
+.. _l2tpv3-interface:
+
+L2TPv3 Interfaces
+-----------------
+
+L2TPv3 is a pseudowire protocol, you can read more about here `Wikipedia L2TPv3`_ or `RFC3921`_
+
+L2TPv3 can transport any traffic including ethernet frames. L2TPv2 is limited to PPP.
+
+
+L2TPv3 over IP
+^^^^^^^^^^^^^^
+
+.. code-block:: sh
+
+  # show interfaces l2tpv3 
+  l2tpv3 l2tpeth10 {
+      address 192.168.37.1/27
+      encapsulation ip
+      local-ip 192.0.2.1
+      peer-session-id 100
+      peer-tunnel-id 200
+      remote-ip 203.0.113.24
+      session-id 100
+      tunnel-id 200
+  }
+
+Inverse configuration has to be applied to the remote side.
+
+L2TPv3 over UDP
+^^^^^^^^^^^^^^^
+
+UDP mode works better with NAT:
+
+* Set local-ip to your local IP (LAN).
+* Add a forwarding rule matching UDP port on your internet router.
+
+.. code-block:: sh
+
+  # show interfaces l2tpv3 
+  l2tpv3 l2tpeth10 {
+      address 192.168.37.1/27
+      destination-port 9001
+      encapsulation udp
+      local-ip 192.0.2.1
+      peer-session-id 100
+      peer-tunnel-id 200
+      remote-ip 203.0.113.24
+      session-id 100
+      source-port 9000
+      tunnel-id 200
+  }
+
+To create more than one tunnel, use distinct UDP ports.
+
+
+L2TPv3 over IPSec, L2 VPN (bridge)
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+This is the LAN extension use case. The eth0 port of the distant VPN peers will be directly connected like if there was a switch between them.
+
+IPSec:
+
+.. code-block:: sh
+
+  set vpn ipsec ipsec-interfaces <VPN-interface>
+  set vpn ipsec esp-group test-ESP-1 compression 'disable'
+  set vpn ipsec esp-group test-ESP-1 lifetime '3600'
+  set vpn ipsec esp-group test-ESP-1 mode 'transport'
+  set vpn ipsec esp-group test-ESP-1 pfs 'enable'
+  set vpn ipsec esp-group test-ESP-1 proposal 1 encryption 'aes128'
+  set vpn ipsec esp-group test-ESP-1 proposal 1 hash 'sha1'
+  set vpn ipsec ike-group test-IKE-1 ikev2-reauth 'no'
+  set vpn ipsec ike-group test-IKE-1 key-exchange 'ikev1'
+  set vpn ipsec ike-group test-IKE-1 lifetime '3600'
+  set vpn ipsec ike-group test-IKE-1 proposal 1 dh-group '5'
+  set vpn ipsec ike-group test-IKE-1 proposal 1 encryption 'aes128'
+  set vpn ipsec ike-group test-IKE-1 proposal 1 hash 'sha1'
+  set vpn ipsec site-to-site peer <peer-ip> authentication mode 'pre-shared-secret'
+  set vpn ipsec site-to-site peer <peer-ip> authentication pre-shared-secret <pre-shared-key>
+  set vpn ipsec site-to-site peer <peer-ip> connection-type 'initiate'
+  set vpn ipsec site-to-site peer <peer-ip> ike-group 'test-IKE-1'
+  set vpn ipsec site-to-site peer <peer-ip> ikev2-reauth 'inherit'
+  set vpn ipsec site-to-site peer <peer-ip> local-address <local-ip>
+  set vpn ipsec site-to-site peer <peer-ip> tunnel 1 allow-nat-networks 'disable'
+  set vpn ipsec site-to-site peer <peer-ip> tunnel 1 allow-public-networks 'disable'
+  set vpn ipsec site-to-site peer <peer-ip> tunnel 1 esp-group 'test-ESP-1'
+  set vpn ipsec site-to-site peer <peer-ip> tunnel 1 protocol 'l2tp'
+
+Bridge:
+
+.. code-block:: sh
+
+  set interfaces bridge br0 description 'L2 VPN Bridge'
+  # remote side in this example:
+  # set interfaces bridge br0 address '172.16.30.18/30'
+  set interfaces bridge br0 address '172.16.30.17/30'
+  set interfaces ethernet eth0 bridge-group bridge 'br0'
+  set interfaces ethernet eth0 description 'L2 VPN Physical port'
+
+L2TPv3:
+
+.. code-block:: sh
+
+  set interfaces l2tpv3 l2tpeth0 bridge-group bridge 'br0'
+  set interfaces l2tpv3 l2tpeth0 description 'L2 VPN Tunnel'
+  set interfaces l2tpv3 l2tpeth0 destination-port '5000'
+  set interfaces l2tpv3 l2tpeth0 encapsulation 'ip'
+  set interfaces l2tpv3 l2tpeth0 local-ip <local-ip>
+  set interfaces l2tpv3 l2tpeth0 mtu '1500'
+  set interfaces l2tpv3 l2tpeth0 peer-session-id '110'
+  set interfaces l2tpv3 l2tpeth0 peer-tunnel-id '10'
+  set interfaces l2tpv3 l2tpeth0 remote-ip <peer-ip>
+  set interfaces l2tpv3 l2tpeth0 session-id '110'
+  set interfaces l2tpv3 l2tpeth0 source-port '5000'
+  set interfaces l2tpv3 l2tpeth0 tunnel-id '10'
+
+.. _`Wikipedia L2TPv3`: http://en.wikipedia.org/wiki/L2TPv3
+.. _`RFC3921`: https://tools.ietf.org/html/rfc3931
\ No newline at end of file