protocols: fix lint errors

6 files changed, 51 insertions, 24 deletions

diff --git a/docs/configuration/protocols/bfd.rst b/docs/configuration/protocols/bfd.rst
index b8fdf489..20ff3b8a 100644
--- a/docs/configuration/protocols/bfd.rst
+++ b/docs/configuration/protocols/bfd.rst
@@ -25,19 +25,22 @@ Configure BFD
 
    Allow this BFD peer to not be directly connected
 
-.. cfgcmd:: set protocols bfd peer <address> source [address <address> | interface <interface>]
+.. cfgcmd:: set protocols bfd peer <address> source 
+   [address <address> | interface <interface>]
 
    Bind listener to specifid interface/address, mandatory for IPv6
 
 .. cfgcmd:: set protocols bfd peer <address> interval echo-interval <10-60000>
 
-   The minimal echo receive transmission interval that this system is capable of handling
+   The minimal echo receive transmission interval that this system is
+   capable of handling
 
 .. cfgcmd:: set protocols bfd peer <address> interval multiplier <2-255>
 
    Remote transmission interval will be multiplied by this value
 
-.. cfgcmd:: set protocols bfd peer <address> interval [receive | transmit] <10-60000>
+.. cfgcmd:: set protocols bfd peer <address> interval 
+   [receive | transmit] <10-60000>
 
    Interval in milliseconds
 
diff --git a/docs/configuration/protocols/igmp.rst b/docs/configuration/protocols/igmp.rst
index 9104b0c9..7109deb6 100644
--- a/docs/configuration/protocols/igmp.rst
+++ b/docs/configuration/protocols/igmp.rst
@@ -96,7 +96,8 @@ These are the commands for a basic setup.
    can communicate with PIM neighbors.
 
 
-.. cfgcmd:: set protocols pim rp address <address> group <multicast-address/mask-bits>
+.. cfgcmd:: set protocols pim rp address <address> group
+   <multicast-address/mask-bits>
 
    Use this comand to manually configure a Rendevouz Point for PIM so
    that join messages can be sent there. Set the Rendevouz Point address
@@ -140,7 +141,8 @@ You can also tune multicast with the following commands.
    platforms cannot see data flowing in better than 30 second chunks.
 
 
-.. cfgcmd:: set protocols igmp interface <interface> join <multicast-address> source <IP-address>
+.. cfgcmd:: set protocols igmp interface <interface> join <multicast-address>
+   source <IP-address>
 
    Use this command to allow the selected interface join a multicast
    group defining the multicast address you want to join and the source
@@ -153,7 +155,8 @@ You can also tune multicast with the following commands.
    host query interval (1-1800) in seconds that PIM will use.
 
 
-.. cfgcmd:: set protocols igmp interface <interface query-max-response-time <deciseconds>
+.. cfgcmd:: set protocols igmp interface <interface query-max-response-time
+   <deciseconds>
 
    Use this command to configure in the selected interface the IGMP
    query response timeout value (10-250) in deciseconds. If a report is
@@ -180,7 +183,8 @@ upstream interface, and one or more downstream interfaces.
 Configuration
 =============
 
-.. cfgcmd:: set protocols igmp-proxy interface <interface> role <upstream | downstream>
+.. cfgcmd:: set protocols igmp-proxy interface <interface> role
+   <upstream | downstream>
 
    * **upstream:** The upstream network interface is the outgoing interface
      which is responsible for communicating to available multicast data sources.
diff --git a/docs/configuration/protocols/isis.rst b/docs/configuration/protocols/isis.rst
index 64cc2535..753637f9 100644
--- a/docs/configuration/protocols/isis.rst
+++ b/docs/configuration/protocols/isis.rst
@@ -6,12 +6,14 @@
 IS-IS
 #####
 
-:abbr:`IS-IS (Intermediate System to Intermediate System)` is a link-state interior gateway routing protocol.
-Like OSPF, IS-IS runs the Dijkstra shortest-path first (SPF) algorithm to create a database of the network’s
-topology and, from that database, to determine the best (that is, shortest) path to a destination.
-The routers exchange topology information with their nearest neighbors.
-IS-IS runs directly on the data link layer (Layer 2).
-IS-IS addresses are called :abbr:`NETs (Network Entity Titles)` and can be 8 to 20 bytes long, but are generally 10 bytes long.
+:abbr:`IS-IS (Intermediate System to Intermediate System)` is a link-state
+interior gateway routing protocol. Like OSPF, IS-IS runs the Dijkstra
+shortest-path first (SPF) algorithm to create a database of the network’s
+topology and, from that database, to determine the best (that is, shortest)
+path to a destination. The routers exchange topology information with their
+nearest neighbors. IS-IS runs directly on the data link layer (Layer 2).
+IS-IS addresses are called :abbr:`NETs (Network Entity Titles)` and can be
+8 to 20 bytes long, but are generally 10 bytes long.
 
 For example :abbr:`NET (Network Entity Title)`
 
@@ -28,12 +30,14 @@ The IS-IS address consists of three parts:
     ``0001`` IS-IS area number (Area1)
 
   System identifier:
-    ``1921.6800.1002`` For system idetifier we recommend to use IP address or MAC address of the router.
+    ``1921.6800.1002`` For system idetifier we recommend to use IP address or
+    MAC address of the router.
 
   NET selector:
     ``00`` Must always be 00, to indicate "this system".
 
-Simple IS-IS configuration using 2 nodes and redistributing connected interfaces.
+Simple IS-IS configuration using 2 nodes and redistributing connected
+interfaces.
 
 **Node 1:**
 
diff --git a/docs/configuration/protocols/mpls.rst b/docs/configuration/protocols/mpls.rst
index 863e7f62..3b59d8ea 100644
--- a/docs/configuration/protocols/mpls.rst
+++ b/docs/configuration/protocols/mpls.rst
@@ -240,4 +240,8 @@ Reset
   Use this command to reset an LDP neighbor/TCP session that is established
 
 
+.. stop_vyoslinter
+
 .. _`Wikipedia (MPLS)`: https://en.wikipedia.org/wiki/Multiprotocol_Label_Switching
+
+.. start_vyoslinter
\ No newline at end of file
diff --git a/docs/configuration/protocols/rpki.rst b/docs/configuration/protocols/rpki.rst
index 9813b1b6..c3ff442b 100644
--- a/docs/configuration/protocols/rpki.rst
+++ b/docs/configuration/protocols/rpki.rst
@@ -100,6 +100,8 @@ Once your routers are configured to reject RPKI-invalid prefixes, you can
 test whether the configuration is working correctly using the `RIPE Labs RPKI
 Test`_ experimental tool.
 
+.. stop_vyoslinter
+
 .. _tweet by EvilMog: https://twitter.com/Evil_Mog/status/1230924170508169216
 .. _Routinator: https://www.nlnetlabs.nl/projects/rpki/routinator/
 .. _GoRTR: https://github.com/cloudflare/gortr
@@ -110,4 +112,6 @@ Test`_ experimental tool.
 .. _RPKI analytics: https://www.nlnetlabs.nl/projects/rpki/rpki-analytics/
 .. _RIPE Labs RPKI Test: https://sg-pub.ripe.net/jasper/rpki-web-test/
 .. _excellent guide to RPKI: https://rpki.readthedocs.io/
-.. _help and operational guidance: https://rpki.readthedocs.io/en/latest/about/help.html
+.. _help and operational guidance: https://rpki.readthedocs.io/en/latest/about/help.htm
+
+.. start_vyoslinter
diff --git a/docs/configuration/protocols/static.rst b/docs/configuration/protocols/static.rst
index 43b77c41..42c0c4b7 100644
--- a/docs/configuration/protocols/static.rst
+++ b/docs/configuration/protocols/static.rst
@@ -28,7 +28,8 @@ Static Routes
 
    Disable this IPv4 static route entry.
 
-.. cfgcmd:: set protocols static route <subnet> next-hop <address> distance <distance>
+.. cfgcmd:: set protocols static route <subnet> next-hop <address>
+   distance <distance>
 
    Defines next-hop distance for this route, routes with smaller administrative
    distance are elected prior those with a higher distance.
@@ -47,7 +48,8 @@ Static Routes
 
    Disable this IPv6 static route entry.
 
-.. cfgcmd:: set protocols static route6 <subnet> next-hop <address> distance <distance>
+.. cfgcmd:: set protocols static route6 <subnet> next-hop <address>
+   distance <distance>
 
    Defines next-hop distance for this route, routes with smaller administrative
    distance are elected prior those with a higher distance.
@@ -61,34 +63,40 @@ Static Routes
 Interface Routes
 ================
 
-.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface <interface>
+.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface
+   <interface>
 
    Allows you to configure the next-hop interface for an interface-based IPv4
    static route. `<interface>` will be the next-hop interface where trafic is
    routed for the given `<subnet>`.
 
-.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface <interface> disable
+.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface
+   <interface> disable
 
    Disables interface-based IPv4 static route.
 
-.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface <interface> distance <distance>
+.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface
+   <interface> distance <distance>
 
    Defines next-hop distance for this route, routes with smaller administrative
    distance are elected prior those with a higher distance.
 
    Range is 1 to 255, default is 1.
 
-.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface <interface>
+.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface
+   <interface>
 
    Allows you to configure the next-hop interface for an interface-based IPv6
    static route. `<interface>` will be the next-hop interface where trafic is
    routed for the given `<subnet>`.
 
-.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface <interface> disable
+.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface
+   <interface> disable
 
    Disables interface-based IPv6 static route.
 
-.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface <interface> distance <distance>
+.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface
+   <interface> distance <distance>
 
    Defines next-hop distance for this route, routes with smaller administrative
    distance are elected prior those with a higher distance.