diff options
| -rw-r--r-- | docs/ch05-network-interfaces.rst | 87 |
1 files changed, 87 insertions, 0 deletions
diff --git a/docs/ch05-network-interfaces.rst b/docs/ch05-network-interfaces.rst index 892d17a9..65d081bc 100644 --- a/docs/ch05-network-interfaces.rst +++ b/docs/ch05-network-interfaces.rst @@ -158,6 +158,7 @@ VLAN interfaces are shown as <name>.<vlan-id>, e.g. eth1.100: eth1.100 192.168.100.1/24 u/u VLAN 100 lo 127.0.0.1/8 u/u ::1/128 + Bridging -------- @@ -353,3 +354,89 @@ Results in: description "Description" } +Wireguard VPN Interface +----------------------- + +WireGuard is an extremely simple yet fast and modern VPN that utilizes state-of-the-art cryptography. +See https://www.wireguard.com for mor information. + +Configuration +^^^^^^^^^^^^^ + +Generate the keypair, which creates a public and private part and stores it within vyos. + +.. code-block:: sh + + wg01:~$ configure + wg01# run generate wireguard keypair + +The public key is being shared with your peer(s), your peer will encrypt all traffic to your system using this public key. + +.. code-block:: sh + + wg01#run show wireguard pubkey + u41jO3OF73Gq1WARMMFG7tOfk7+r8o8AzPxJ1FZRhzk= + +The next step is to configure your local side as well as the policy based trusted destination addresses. +If you only initiate a connection, the listen port and endpoint is optional, if you however act as a server and endpoints initiate the connections to your system, you need to define a port your clients can connect to, otherwise it's randomly chosen and may make it difficult with firewall rules, since the port may be a different one when you reboot your system. + +You will also need the public key of your peer as well as the network(s) you want to tunnel (allowed-ips) to configure a wireguard tunnel. +The public key below is always the public key from your peer, not your local one. + +**local side** + +.. code-block:: sh + + set interfaces wireguard wg01 address '10.1.0.1/24' + set interfaces wireguard wg01 description 'VPN-to-wg02' + set interfaces wireguard wg01 peer to-wg02 allowed-ips '10.2.0.0/24' + set interfaces wireguard wg01 peer to-wg02 endpoint '192.168.0.142:12345' + set interfaces wireguard wg01 peer to-wg02 pubkey 'XMrlPykaxhdAAiSjhtPlvi30NVkvLQliQuKP7AI7CyI=' + set interfaces wireguard wg01 port '12345' + set protocols static interface-route 10.2.0.0/24 next-hop-interface wg01 + +The last step is to define an interface route for 10.2.0.0/24 to get through the wireguard interface wg01. +Multiple IPs or networks can be defined and routed, the last check is allowed-ips which either prevents or allows the traffic. + +**remote side** + +.. code-block:: sh + + set interfaces wireguard wg01 address '10.2.0.1/24' + set interfaces wireguard wg01 description 'VPN-to-wg01' + set interfaces wireguard wg01 peer to-wg02 allowed-ips '10.1.0.0/24' + set interfaces wireguard wg01 peer to-wg02 endpoint '192.168.0.124:12345' + set interfaces wireguard wg01 peer to-wg02 pubkey 'u41jO3OF73Gq1WARMMFG7tOfk7+r8o8AzPxJ1FZRhzk=' + set interfaces wireguard wg01 port '12345' + set protocols static interface-route 10.1.0.0/24 next-hop-interface wg01 + +Assure that your firewall rules allow the traffic, in which case you have a working VPN using wireguard. + +.. code-block:: sh + + wg01# ping 10.2.0.1 + PING 10.2.0.1 (10.2.0.1) 56(84) bytes of data. + 64 bytes from 10.2.0.1: icmp_seq=1 ttl=64 time=1.16 ms + 64 bytes from 10.2.0.1: icmp_seq=2 ttl=64 time=1.77 ms + + wg02# ping 10.1.0.1 + PING 10.1.0.1 (10.1.0.1) 56(84) bytes of data. + 64 bytes from 10.1.0.1: icmp_seq=1 ttl=64 time=4.40 ms + 64 bytes from 10.1.0.1: icmp_seq=2 ttl=64 time=1.02 ms + +An additional layer of symmetric-key crypto can be used on top of the asymmetric crypto, which is optional. + +.. code-block:: sh + + wg01# run generate wireguard preshared-key + rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc= + +Copy the key, it is not stored on the local file system. +Make sure you distribute that key in a safe manner, it's a symmatric key, so only you and your peer should have knowledge if its content. + +.. code-block:: sh + + wg01# set interfaces wireguard wg01 peer to-wg02 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc=' + wg02# set interfaces wireguard wg01 peer to-wg01 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc=' + + |