diff options
| -rw-r--r-- | docs/configuration/interfaces/tunnel.rst | 40 |
1 files changed, 20 insertions, 20 deletions
diff --git a/docs/configuration/interfaces/tunnel.rst b/docs/configuration/interfaces/tunnel.rst index d2d63ce2..36b1d70b 100644 --- a/docs/configuration/interfaces/tunnel.rst +++ b/docs/configuration/interfaces/tunnel.rst @@ -32,8 +32,8 @@ An example: .. code-block:: none set interfaces tunnel tun0 encapsulation ipip - set interfaces tunnel tun0 local-ip 192.0.2.10 - set interfaces tunnel tun0 remote-ip 203.0.113.20 + set interfaces tunnel tun0 source-address 192.0.2.10 + set interfaces tunnel tun0 remote 203.0.113.20 set interfaces tunnel tun0 address 192.168.100.200/24 IP6IP6 @@ -50,8 +50,8 @@ An example: .. code-block:: none set interfaces tunnel tun0 encapsulation ip6ip6 - set interfaces tunnel tun0 local-ip 2001:db8:aa::1 - set interfaces tunnel tun0 remote-ip 2001:db8:aa::2 + set interfaces tunnel tun0 source-address 2001:db8:aa::1 + set interfaces tunnel tun0 remote 2001:db8:aa::2 set interfaces tunnel tun0 address 2001:db8:bb::1/64 IPIP6 @@ -67,8 +67,8 @@ An example: .. code-block:: none set interfaces tunnel tun0 encapsulation ipip6 - set interfaces tunnel tun0 local-ip 2001:db8:aa::1 - set interfaces tunnel tun0 remote-ip 2001:db8:aa::2 + set interfaces tunnel tun0 source-address 2001:db8:aa::1 + set interfaces tunnel tun0 remote 2001:db8:aa::2 set interfaces tunnel tun0 address 192.168.70.80/24 6in4 (SIT) @@ -89,8 +89,8 @@ An example: .. code-block:: none set interfaces tunnel tun0 encapsulation sit - set interfaces tunnel tun0 local-ip 192.0.2.10 - set interfaces tunnel tun0 remote-ip 192.0.2.20 + set interfaces tunnel tun0 source-address 192.0.2.10 + set interfaces tunnel tun0 remote 192.0.2.20 set interfaces tunnel tun0 address 2001:db8:bb::1/64 A full example of a Tunnelbroker.net config can be found at @@ -112,8 +112,8 @@ over either IPv4 (gre) or IPv6 (ip6gre). Configuration ^^^^^^^^^^^^^ -A basic configuration requires a tunnel source (local-ip), a tunnel destination -(remote-ip), an encapsulation type (gre), and an address (ipv4/ipv6).Below is a +A basic configuration requires a tunnel source (source-address), a tunnel destination +(remote), an encapsulation type (gre), and an address (ipv4/ipv6).Below is a basic IPv4 only configuration example taken from a VyOS router and a Cisco IOS router. The main difference between these two configurations is that VyOS requires you explicitly configure the encapsulation type. The Cisco router @@ -125,8 +125,8 @@ defaults to gre ip otherwise it would have to be configured as well. set interfaces tunnel tun100 address '10.0.0.1/30' set interfaces tunnel tun100 encapsulation 'gre' - set interfaces tunnel tun100 local-ip '198.51.100.2' - set interfaces tunnel tun100 remote-ip '203.0.113.10' + set interfaces tunnel tun100 source-address '198.51.100.2' + set interfaces tunnel tun100 remote '203.0.113.10' **Cisco IOS Router:** @@ -147,8 +147,8 @@ and a Linux host using systemd-networkd. set interfaces tunnel tun101 address '2001:db8:feed:beef::1/126' set interfaces tunnel tun101 address '192.168.5.1/30' set interfaces tunnel tun101 encapsulation 'ip6gre' - set interfaces tunnel tun101 local-ip '2001:db8:babe:face::3afe:3' - set interfaces tunnel tun101 remote-ip '2001:db8:9bb:3ce::5' + set interfaces tunnel tun101 source-address '2001:db8:babe:face::3afe:3' + set interfaces tunnel tun101 remote '2001:db8:9bb:3ce::5' **Linux systemd-networkd:** @@ -189,15 +189,15 @@ An example: .. code-block:: none - set interfaces tunnel tun0 local-ip 192.0.2.10 - set interfaces tunnel tun0 remote-ip 192.0.2.20 + set interfaces tunnel tun0 source-address 192.0.2.10 + set interfaces tunnel tun0 remote 192.0.2.20 set interfaces tunnel tun0 address 10.40.50.60/24 set interfaces tunnel tun0 parameters ip key 10 - + .. code-block:: none - set interfaces tunnel tun0 local-ip 192.0.2.10 - set interfaces tunnel tun0 remote-ip 192.0.2.20 + set interfaces tunnel tun0 source-address 192.0.2.10 + set interfaces tunnel tun0 remote 192.0.2.20 set interfaces tunnel tun0 address 172.16.17.18/24 set interfaces tunnel tun0 parameters ip key 20 @@ -211,7 +211,7 @@ to make sure the configuration performs as expected. A common cause for GRE tunnels to fail to come up correctly include ACL or Firewall configurations that are discarding IP protocol 47 or blocking your source/desintation traffic. -**1. Confirm IP connectivity between tunnel local-ip and remote-ip:** +**1. Confirm IP connectivity between tunnel source-address and remote:** .. code-block:: none |