diff options
Diffstat (limited to 'docs/configuration/interfaces/tunnel.rst')
| -rw-r--r-- | docs/configuration/interfaces/tunnel.rst | 50 |
1 files changed, 25 insertions, 25 deletions
diff --git a/docs/configuration/interfaces/tunnel.rst b/docs/configuration/interfaces/tunnel.rst index 8a308348..9fa5ed17 100644 --- a/docs/configuration/interfaces/tunnel.rst +++ b/docs/configuration/interfaces/tunnel.rst @@ -34,8 +34,8 @@ An example: .. code-block:: none set interfaces tunnel tun0 encapsulation ipip - set interfaces tunnel tun0 local-ip 192.0.2.10 - set interfaces tunnel tun0 remote-ip 203.0.113.20 + set interfaces tunnel tun0 source-address 192.0.2.10 + set interfaces tunnel tun0 remote 203.0.113.20 set interfaces tunnel tun0 address 192.168.100.200/24 IP6IP6 @@ -52,8 +52,8 @@ An example: .. code-block:: none set interfaces tunnel tun0 encapsulation ip6ip6 - set interfaces tunnel tun0 local-ip 2001:db8:aa::1 - set interfaces tunnel tun0 remote-ip 2001:db8:aa::2 + set interfaces tunnel tun0 source-address 2001:db8:aa::1 + set interfaces tunnel tun0 remote 2001:db8:aa::2 set interfaces tunnel tun0 address 2001:db8:bb::1/64 IPIP6 @@ -69,8 +69,8 @@ An example: .. code-block:: none set interfaces tunnel tun0 encapsulation ipip6 - set interfaces tunnel tun0 local-ip 2001:db8:aa::1 - set interfaces tunnel tun0 remote-ip 2001:db8:aa::2 + set interfaces tunnel tun0 source-address 2001:db8:aa::1 + set interfaces tunnel tun0 remote 2001:db8:aa::2 set interfaces tunnel tun0 address 192.168.70.80/24 6in4 (SIT) @@ -91,8 +91,8 @@ An example: .. code-block:: none set interfaces tunnel tun0 encapsulation sit - set interfaces tunnel tun0 local-ip 192.0.2.10 - set interfaces tunnel tun0 remote-ip 192.0.2.20 + set interfaces tunnel tun0 source-address 192.0.2.10 + set interfaces tunnel tun0 remote 192.0.2.20 set interfaces tunnel tun0 address 2001:db8:bb::1/64 A full example of a Tunnelbroker.net config can be found at @@ -114,8 +114,8 @@ over either IPv4 (gre) or IPv6 (ip6gre). Configuration ^^^^^^^^^^^^^ -A basic configuration requires a tunnel source (local-ip), a tunnel destination -(remote-ip), an encapsulation type (gre), and an address (ipv4/ipv6). Below is a +A basic configuration requires a tunnel source (source-address), a tunnel destination +(remote), an encapsulation type (gre), and an address (ipv4/ipv6). Below is a basic IPv4 only configuration example taken from a VyOS router and a Cisco IOS router. The main difference between these two configurations is that VyOS requires you explicitly configure the encapsulation type. The Cisco router @@ -127,8 +127,8 @@ defaults to GRE IP otherwise it would have to be configured as well. set interfaces tunnel tun100 address '10.0.0.1/30' set interfaces tunnel tun100 encapsulation 'gre' - set interfaces tunnel tun100 local-ip '198.51.100.2' - set interfaces tunnel tun100 remote-ip '203.0.113.10' + set interfaces tunnel tun100 source-address '198.51.100.2' + set interfaces tunnel tun100 remote '203.0.113.10' **Cisco IOS Router:** @@ -149,8 +149,8 @@ and a Linux host using systemd-networkd. set interfaces tunnel tun101 address '2001:db8:feed:beef::1/126' set interfaces tunnel tun101 address '192.168.5.1/30' set interfaces tunnel tun101 encapsulation 'ip6gre' - set interfaces tunnel tun101 local-ip '2001:db8:babe:face::3afe:3' - set interfaces tunnel tun101 remote-ip '2001:db8:9bb:3ce::5' + set interfaces tunnel tun101 source-address '2001:db8:babe:face::3afe:3' + set interfaces tunnel tun101 remote '2001:db8:9bb:3ce::5' **Linux systemd-networkd:** @@ -191,23 +191,23 @@ An example: .. code-block:: none - set interfaces tunnel tun0 local-ip 192.0.2.10 - set interfaces tunnel tun0 remote-ip 192.0.2.20 + set interfaces tunnel tun0 source-address 192.0.2.10 + set interfaces tunnel tun0 remote 192.0.2.20 set interfaces tunnel tun0 address 10.40.50.60/24 set interfaces tunnel tun0 parameters ip key 10 - + .. code-block:: none - set interfaces tunnel tun0 local-ip 192.0.2.10 - set interfaces tunnel tun0 remote-ip 192.0.2.20 + set interfaces tunnel tun0 source-address 192.0.2.10 + set interfaces tunnel tun0 remote 192.0.2.20 set interfaces tunnel tun0 address 172.16.17.18/24 set interfaces tunnel tun0 parameters ip key 20 GRE-Bridge ^^^^^^^^^^ -While normal GRE is for layer 3, GRE-Bridge is for layer 2. GRE-Bridge can -encapsulate Ethernet frames, thus it can be bridged with other interfaces to +While normal GRE is for layer 3, GRE-Bridge is for layer 2. GRE-Bridge can +encapsulate Ethernet frames, thus it can be bridged with other interfaces to create datalink layer segments that span multiple remote sites. Layer 2 GRE example: @@ -216,9 +216,9 @@ Layer 2 GRE example: set interfaces bridge br0 member interface eth0 set interfaces bridge br0 member interface tun0 - set interfaces tunnel tun0 encapsulation gre-bridge - set interfaces tunnel tun0 local-ip 198.51.100.2 - set interfaces tunnel tun0 remote-ip 203.0.113.10 + set interfaces tunnel tun0 encapsulation gretap + set interfaces tunnel tun0 source-address 192.0.2.100 + set interfaces tunnel tun0 remote 192.0.2.1 Troubleshooting ^^^^^^^^^^^^^^^ @@ -229,7 +229,7 @@ to make sure the configuration performs as expected. A common cause for GRE tunnels to fail to come up correctly include ACL or Firewall configurations that are discarding IP protocol 47 or blocking your source/destination traffic. -**1. Confirm IP connectivity between tunnel local-ip and remote-ip:** +**1. Confirm IP connectivity between tunnel source-address and remote:** .. code-block:: none |