diff options
Diffstat (limited to 'docs/configuration/interfaces')
| -rw-r--r-- | docs/configuration/interfaces/wireguard.rst | 238 |
1 files changed, 119 insertions, 119 deletions
diff --git a/docs/configuration/interfaces/wireguard.rst b/docs/configuration/interfaces/wireguard.rst index 8ba707f6..bbcdc209 100644 --- a/docs/configuration/interfaces/wireguard.rst +++ b/docs/configuration/interfaces/wireguard.rst @@ -1,4 +1,4 @@ -:lastproofread: 2021-07-27 +:lastproofread: 2021-10-01 .. _wireguard: @@ -18,113 +18,159 @@ This diagram corresponds with the example site to site configuration below. .. figure:: /_static/images/wireguard_site2site_diagram.jpg -************* -Configuration -************* - - - ******** Keypairs ******** -WireGuard requires the generation of a keypair, which includes a private -key to decrypt incoming traffic, and a public key for peer(s) to encrypt -traffic. +WireGuard requires the generation of a keypair, which includes a private key to +decrypt incoming traffic, and a public key for peer(s) to encrypt traffic. Generate Keypair ================ -.. opcmd:: generate wireguard default-keypair +.. opcmd:: generate pki wireguard key-pair - It generates the keypair, which includes the public and private parts, - and stores it within VyOS. It will be used per default on any configured - WireGuard interface, even if multiple interfaces are being configured. + It generates the keypair, which includes the public and private parts. + The key is not stored on the system - only a keypair is generated. -.. opcmd:: show wireguard keypairs pubkey default + .. code-block:: none + + vyos@vyos:~$ generate pki wireguard key-pair + Private key: iJJyEARGK52Ls1GYRCcFvPuTj7WyWYDo//BknoDU0XY= + Public key: EKY0dxRrSD98QHjfHOK13mZ5PJ7hnddRZt5woB3szyw= - It shows the public key to be shared with your peer(s). Your peer will - encrypt all traffic to your system using this public key. +.. opcmd:: generate pki wireguard key-pair install interface <interface> + + Generates a keypair, which includes the public and private parts, and build + a configuration command to install this key to ``interface``. .. code-block:: none - vyos@vyos:~$ show wireguard keypairs pubkey default - hW17UxY7zeydJNPIyo3UtGnBHkzTK/NeBOrDSIU9Tx0= + vyos@vyos:~$ generate pki wireguard key-pair install interface wg10 + "generate" CLI command executed from operational level. + Generated private-key is not stored to CLI, use configure mode commands to install key: + set interfaces wireguard wg10 private-key '4Krkv8h6NkAYMMaBWI957yYDJDMvj9URTHstdlOcDU0=' -Generate Named Keypair -====================== + Corresponding public-key to use on peer system is: 'UxDsYT6EnpTIOKUzvMlw2p0sNOKQvFxEdSVrnNrX1Ro=' -Named keypairs can be used on a interface basis when configured. If -multiple WireGuard interfaces are being configured, each can have their -own keypairs. + .. note:: If this command is invoked from configure mode with the ``run`` + prefix the key is automatically installed to the appropriate interface: -.. opcmd:: generate wireguard named-keypairs <name> + .. code-block:: none - The commands below generates 2 keypairs unrelated to each other. + vyos@vyos# run generate pki wireguard key-pair install interface wg10 + "generate" CLI command executed from config session. + Generated private-key was imported to CLI! - .. code-block:: none + Use the following command to verify: show interfaces wireguard wg10 + Corresponding public-key to use on peer system is: '7d9KwabjLhHpJiEJeIGd0CBlao/eTwFOh6xyCovTfG8=' + + vyos@vyos# compare + [edit interfaces] + +wireguard wg10 { + + private-key CJweb8FC6BU3Loj4PC2pn5V82cDjIPs7G1saW0ZfLWc= + +} + +.. opcmd:: show interfaces wireguard <interface> public-key + + Retrieve public key portion from configured WIreGuard interface. + + .. code-block:: none + + vyos@vyos:~$ show interfaces wireguard wg01 public-key + EKY0dxRrSD98QHjfHOK13mZ5PJ7hnddRZt5woB3szyw= + + +Optional +-------- + +.. opcmd:: generate pki wireguard preshared-key + + An additional layer of symmetric-key crypto can be used on top of the + asymmetric crypto. + + This is optional. + + .. code-block:: none + + vyos@vyos:~$ generate pki wireguard preshared-key + Pre-shared key: OHH2EwZfMNK+1L6BXbYw3bKCtMrfjpR4mCAEeBlFnRs= + + +.. opcmd:: generate pki wireguard preshared-key install interface <interface> peer <peer> + + An additional layer of symmetric-key crypto can be used on top of the + asymmetric crypto. This command automatically creates for you the required + CLI command to install this PSK for a given peer. + + This is optional. + + .. code-block:: none + + vyos@vyos:~$ generate pki wireguard preshared-key install interface wg10 peer foo + "generate" CLI command executed from operational level. + Generated preshared-key is not stored to CLI, use configure mode commands to install key: + + set interfaces wireguard wg10 peer foo preshared-key '32vQ1w1yFKTna8n7Gu7EimubSe2Y63m8bafz55EG3Ro=' + + Pre-shared key: +LuaZ8W6DjsDFJFX3jJzoNqrsXHhvq08JztM9z8LHCs= - vyos@vyos:~$ generate wireguard named-keypairs KP01 - vyos@vyos:~$ generate wireguard named-keypairs KP02 + + .. note:: If this command is invoked from configure mode with the ``run`` + prefix the key is automatically installed to the appropriate interface: *********************** Interface configuration *********************** -The next step is to configure your local side as well as the policy -based trusted destination addresses. If you only initiate a connection, -the listen port and address/port is optional; however, if you act like a -server and endpoints initiate the connections to your system, you need to -define a port your clients can connect to, otherwise the port is randomly -chosen and may make connection difficult with firewall rules, since the port -may be different each time the system is rebooted. +The next step is to configure your local side as well as the policy based +trusted destination addresses. If you only initiate a connection, the listen +port and address/port is optional; however, if you act like a server and +endpoints initiate the connections to your system, you need to define a port +your clients can connect to, otherwise the port is randomly chosen and may +make connection difficult with firewall rules, since the port may be different +each time the system is rebooted. -You will also need the public key of your peer as well as the network(s) -you want to tunnel (allowed-ips) to configure a WireGuard tunnel. The -public key below is always the public key from your peer, not your local -one. +You will also need the public key of your peer as well as the network(s) you +want to tunnel (allowed-ips) to configure a WireGuard tunnel. The public key +below is always the public key from your peer, not your local one. **local side - commands** +- WireGuard interface itself uses address 10.1.0.1/30 +- We only allow the 192.168.2.0/24 subnet to travel over the tunnel +- Our remote end of the tunnel for peer `to-wg02` is reachable at 192.0.2.1 + port 51820 +- The remote peer `to-wg02` uses XMrlPykaxhdAAiSjhtPlvi30NVkvLQliQuKP7AI7CyI= + as its public key portion +- We listen on port 51820 +- We route all traffic for the 192.168.2.0/24 network to interface `wg01` + .. code-block:: none set interfaces wireguard wg01 address '10.1.0.1/30' - set interfaces wireguard wg01 description 'VPN-to-wg02' set interfaces wireguard wg01 peer to-wg02 allowed-ips '192.168.2.0/24' - set interfaces wireguard wg01 peer to-wg02 address '<Site1 Pub IP>' + set interfaces wireguard wg01 peer to-wg02 address '192.0.2.1' set interfaces wireguard wg01 peer to-wg02 port '51820' set interfaces wireguard wg01 peer to-wg02 pubkey 'XMrlPykaxhdAAiSjhtPlvi30NVkvLQliQuKP7AI7CyI=' set interfaces wireguard wg01 port '51820' - set protocols static route 192.168.2.0/24 interface wg01 -**local side - annotated commands** + set protocols static route 192.168.2.0/24 interface wg01 -.. code-block:: none +The last step is to define an interface route for 192.168.2.0/24 to get through +the WireGuard interface `wg01`. Multiple IPs or networks can be defined and +routed. The last check is allowed-ips which either prevents or allows the +traffic. - set interfaces wireguard wg01 address '10.1.0.1/30' # Address of the wg01 tunnel interface. - set interfaces wireguard wg01 description 'VPN-to-wg02' - set interfaces wireguard wg01 peer to-wg02 allowed-ips '192.168.2.0/24' # Subnets that are allowed to travel over the tunnel - set interfaces wireguard wg01 peer to-wg02 address '<Site2 Pub IP>' # Public IP of the peer - set interfaces wireguard wg01 peer to-wg02 port '58120' # Port of the Peer - set interfaces wireguard wg01 peer to-wg02 pubkey '<pubkey>' # Public Key of the Peer - set interfaces wireguard wg01 port '51820' # Port of own server - set protocols static route 192.168.2.0/24 interface wg01 # Static route to remote subnet - -The last step is to define an interface route for 192.168.2.0/24 to get -through the WireGuard interface `wg01`. Multiple IPs or networks can be -defined and routed. The last check is allowed-ips which either prevents -or allows the traffic. - -.. note:: You can not assign the same allowed-ips statement to multiple +.. warning:: You can not assign the same allowed-ips statement to multiple WireGuard peers. This a design decision. For more information please check the `WireGuard mailing list`_. .. cfgcmd:: set interfaces wireguard <interface> private-key <name> - To use a named key on an interface, the option private-key needs to be - set. + To use a named key on an interface, the option private-key needs to be set. .. code-block:: none @@ -133,7 +179,6 @@ or allows the traffic. The command :opcmd:`show wireguard keypairs pubkey KP01` will then show the public key, which needs to be shared with the peer. - **remote side - commands** .. code-block:: none @@ -141,24 +186,12 @@ or allows the traffic. set interfaces wireguard wg01 address '10.1.0.2/30' set interfaces wireguard wg01 description 'VPN-to-wg01' set interfaces wireguard wg01 peer to-wg02 allowed-ips '192.168.1.0/24' - set interfaces wireguard wg01 peer to-wg02 address '<Site1 Pub IP>' + set interfaces wireguard wg01 peer to-wg02 address '192.0.2.2' set interfaces wireguard wg01 peer to-wg02 port '51820' set interfaces wireguard wg01 peer to-wg02 pubkey 'u41jO3OF73Gq1WARMMFG7tOfk7+r8o8AzPxJ1FZRhzk=' set interfaces wireguard wg01 port '51820' - set protocols static route 192.168.1.0/24 interface wg01 -**remote side - annotated commands** - -.. code-block:: none - - set interfaces wireguard wg01 address '10.1.0.2/30' # Address of the wg01 tunnel interface. - set interfaces wireguard wg01 description 'VPN-to-wg01' - set interfaces wireguard wg01 peer to-wg02 allowed-ips '192.168.1.0/24' # Subnets that are allowed to travel over the tunnel - set interfaces wireguard wg01 peer to-wg02 address 'Site1 Pub IP' # Public IP address of the Peer - set interfaces wireguard wg01 peer to-wg02 port '51820' # Port of the Peer - set interfaces wireguard wg01 peer to-wg02 pubkey '<pubkey>' # Public key of the Peer - set interfaces wireguard wg01 port '51820' # Port of own server - set protocols static route 192.168.1.0/24 interface wg01 # Static route to remote subnet + set protocols static route 192.168.1.0/24 interface wg01 ******************* Firewall Exceptions @@ -207,7 +240,7 @@ asymmetric crypto. This is optional. .. code-block:: none - wg01# run generate wireguard preshared-key + vyos@vyos:~$ generate pki wireguard preshared-key install rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc= Copy the key, as it is not stored on the local filesystem. Because it @@ -234,17 +267,17 @@ the peers. This allows the peers to interact with one another. wireguard wg0 { address 10.172.24.1/24 - address 2001:DB8:470:22::1/64 + address 2001:db8:470:22::1/64 description RoadWarrior peer MacBook { allowed-ips 10.172.24.30/32 - allowed-ips 2001:DB8:470:22::30/128 + allowed-ips 2001:db8:470:22::30/128 persistent-keepalive 15 pubkey F5MbW7ye7DsoxdOaixjdrudshjjxN5UdNV+pGFHqehc= } peer iPhone { allowed-ips 10.172.24.20/32 - allowed-ips 2001:DB8:470:22::20/128 + allowed-ips 2001:db8:470:22::20/128 persistent-keepalive 15 pubkey BknHcLFo8nOo8Dwq2CjaC/TedchKQ0ebxC7GYn7Al00= } @@ -259,7 +292,7 @@ through the connection. [Interface] PrivateKey = ARAKLSDJsadlkfjasdfiowqeruriowqeuasdf= - Address = 10.172.24.20/24, 2001:DB8:470:22::20/64 + Address = 10.172.24.20/24, 2001:db8:470:22::20/64 DNS = 10.0.0.53, 10.0.0.54 [Peer] @@ -276,11 +309,11 @@ tunnel. All other traffic is unaffected. [Interface] PrivateKey = 8Iasdfweirousd1EVGUk5XsT+wYFZ9mhPnQhmjzaJE6Go= - Address = 10.172.24.30/24, 2001:DB8:470:22::30/64 + Address = 10.172.24.30/24, 2001:db8:470:22::30/64 [Peer] PublicKey = RIbtUTCfgzNjnLNPQ/ulkGnnB2vMWHm7l2H/xUfbyjc= - AllowedIPs = 10.172.24.30/24, 2001:DB8:470:22::/64 + AllowedIPs = 10.172.24.30/24, 2001:db8:470:22::/64 Endpoint = 192.0.2.1:2224 PersistentKeepalive = 25 @@ -294,14 +327,14 @@ Status .. opcmd:: show interfaces wireguard wg0 summary - Show info about the Wireguard service. + Show info about the Wireguard service. It also shows the latest handshake. .. code-block:: none vyos@vyos:~$ show interfaces wireguard wg0 summary interface: wg0 - public key: + public key: private key: (hidden) listening port: 51820 @@ -341,39 +374,6 @@ Status TX: bytes packets errors dropped carrier collisions 0 0 0 0 0 0 -*************** -Encryption Keys -*************** - -.. opcmd:: show wireguard keypair pubkey <name> - - Show public key portion for specified key. This can be either the ``default`` - key, or any other named key-pair. - - The ``default`` keypair - - .. code-block:: none - - vyos@vyos:~$ show wireguard keypair pubkey default - FAXCPb6EbTlSH5200J5zTopt9AYXneBthAySPBLbZwM= - - Name keypair ``KP01`` - - .. code-block:: none - - vyos@vyos:~$ show wireguard keypair pubkey KP01 - HUtsu198toEnm1poGoRTyqkUKfKUdyh54f45dtcahDM= - -.. opcmd:: delete wireguard keypair pubkey <name> - - Delete a keypair, this can be either the ``default`` key, or any other - named key-pair. - - .. code-block:: none - - vyos@vyos:~$ delete wireguard keypair default - - *********************************** Remote Access "RoadWarrior" clients *********************************** |