diff options
Diffstat (limited to 'docs/configuration/protocols/ospf.rst')
| -rw-r--r-- | docs/configuration/protocols/ospf.rst | 17 |
1 files changed, 9 insertions, 8 deletions
diff --git a/docs/configuration/protocols/ospf.rst b/docs/configuration/protocols/ospf.rst index e3f9759e..4949cded 100644 --- a/docs/configuration/protocols/ospf.rst +++ b/docs/configuration/protocols/ospf.rst @@ -43,7 +43,8 @@ starts when the first ospf enabled interface is configured. enable ospf on interface with address 192.168.1.1/23, but it does on interface with address 192.168.1.129/25. - In some cases it may be more convenient to enable OSPF on a per interface/subnet + In some cases it may be more convenient to enable OSPF on a per + interface/subnet basis :cfgcmd:`set protocols ospf interface <interface> area <x.x.x.x | x>` .. cfgcmd:: set protocols ospf auto-cost reference-bandwidth <number> @@ -790,7 +791,7 @@ General VyOS does not have a special command to start the OSPFv3 process. The OSPFv3 process starts when the first ospf enabled interface is configured. -.. cfgcmd:: set protocols ospfv3 area <number> interface <interface> +.. cfgcmd:: set protocols ospfv3 interface <interface> area <number> This command specifies the OSPFv3 enabled interface. This command is also used to enable the OSPF process. The area number can be specified in @@ -987,7 +988,7 @@ A typical configuration using 2 nodes. .. code-block:: none - set protocols ospfv3 area 0.0.0.0 interface eth1 + set protocols ospfv3 interface eth1 area 0.0.0.0 set protocols ospfv3 area 0.0.0.0 range 2001:db8:1::/64 set protocols ospfv3 parameters router-id 192.168.1.1 set protocols ospfv3 redistribute connected @@ -996,7 +997,7 @@ A typical configuration using 2 nodes. .. code-block:: none - set protocols ospfv3 area 0.0.0.0 interface eth1 + set protocols ospfv3 interface eth1 area 0.0.0.0 set protocols ospfv3 area 0.0.0.0 range 2001:db8:2::/64 set protocols ospfv3 parameters router-id 192.168.2.1 set protocols ospfv3 redistribute connected @@ -1025,8 +1026,8 @@ Example configuration for WireGuard interfaces: set interfaces wireguard wg01 peer ospf02 pubkey 'ie3...=' set interfaces wireguard wg01 port '12345' set protocols ospfv3 parameters router-id 192.168.1.1 - set protocols ospfv3 area 0.0.0.0 interface 'wg01' - set protocols ospfv3 area 0.0.0.0 interface 'lo' + set protocols ospfv3 interface 'wg01' area 0.0.0.0 + set protocols ospfv3 interface 'lo' area 0.0.0.0 **Node 2** @@ -1040,8 +1041,8 @@ Example configuration for WireGuard interfaces: set interfaces wireguard wg01 peer ospf01 pubkey 'NHI...=' set interfaces wireguard wg01 port '12345' set protocols ospfv3 parameters router-id 192.168.1.2 - set protocols ospfv3 area 0.0.0.0 interface 'wg01' - set protocols ospfv3 area 0.0.0.0 interface 'lo' + set protocols ospfv3 interface 'wg01' area 0.0.0.0 + set protocols ospfv3 interface 'lo' area 0.0.0.0 **Status** |