diff options
Diffstat (limited to 'docs/configuration/protocols/static.rst')
| -rw-r--r-- | docs/configuration/protocols/static.rst | 195 |
1 files changed, 195 insertions, 0 deletions
diff --git a/docs/configuration/protocols/static.rst b/docs/configuration/protocols/static.rst new file mode 100644 index 00000000..fbde8228 --- /dev/null +++ b/docs/configuration/protocols/static.rst @@ -0,0 +1,195 @@ +.. _static-routing: + +###### +Static +###### + +Static routes are manually configured routes, which, in general, cannot be +updated dynamically from information VyOS learns about the network topology from +other routing protocols. However, if a link fails, the router will remove +routes, including static routes, from the :abbr:`RIPB (Routing Information +Base)` that used this interface to reach the next hop. In general, static +routes should only be used for very simple network topologies, or to override +the behavior of a dynamic routing protocol for a small number of routes. The +collection of all routes the router has learned from its configuration or from +its dynamic routing protocols is stored in the RIB. Unicast routes are directly +used to determine the forwarding table used for unicast packet forwarding. + +Static Routes +############# + +.. cfgcmd:: set protocols static route <subnet> next-hop <address> + + Configure next-hop `<address>` for an IPv4 static route. Multiple static + routes can be created. + +.. cfgcmd:: set protocols static route <subnet> next-hop <address> disable + + Disable this IPv4 static route entry. + +.. cfgcmd:: set protocols static route <subnet> next-hop <address> distance <distance> + + Defines next-hop distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + Range is 1 to 255, default is 1. + + .. note:: Routes with a distance of 255 are effectively disabled and not + installed into the kernel. + +.. cfgcmd:: set protocols static route6 <subnet> next-hop <address> + + Configure next-hop `<address>` for an IPv6 static route. Multiple static + routes can be created. + +.. cfgcmd:: set protocols static route6 <subnet> next-hop <address> disable + + Disable this IPv6 static route entry. + +.. cfgcmd:: set protocols static route6 <subnet> next-hop <address> distance <distance> + + Defines next-hop distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + Range is 1 to 255, default is 1. + + .. note:: Routes with a distance of 255 are effectively disabled and not + installed into the kernel. + + +Interface Routes +================ + +.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface <interface> + + Allows you to configure the next-hop interface for an interface-based IPv4 + static route. `<interface>` will be the next-hop interface where trafic is + routed for the given `<subnet>`. + +.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface <interface> disable + + Disables interface-based IPv4 static route. + +.. cfgcmd:: set protocols static interface-route <subnet> next-hop-interface <interface> distance <distance> + + Defines next-hop distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + Range is 1 to 255, default is 1. + +.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface <interface> + + Allows you to configure the next-hop interface for an interface-based IPv6 + static route. `<interface>` will be the next-hop interface where trafic is + routed for the given `<subnet>`. + +.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface <interface> disable + + Disables interface-based IPv6 static route. + +.. cfgcmd:: set protocols static interface-route6 <subnet> next-hop-interface <interface> distance <distance> + + Defines next-hop distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + Range is 1 to 255, default is 1. + + +Blackhole +========= + +.. cfgcmd:: set protocols static route <subnet> blackhole + + Use this command to configure a "black-hole" route on the router. A + black-hole route is a route for which the system silently discard packets + that are matched. This prevents networks leaking out public interfaces, but + it does not prevent them from being used as a more specific route inside your + network. + +.. cfgcmd:: set protocols static route <subnet> blackhole distance <distance> + + Defines blackhole distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + +.. cfgcmd:: set protocols static route6 <subnet> blackhole + + Use this command to configure a "black-hole" route on the router. A + black-hole route is a route for which the system silently discard packets + that are matched. This prevents networks leaking out public interfaces, but + it does not prevent them from being used as a more specific route inside your + network. + +.. cfgcmd:: set protocols static route6 <subnet> blackhole distance <distance> + + Defines blackhole distance for this route, routes with smaller administrative + distance are elected prior those with a higher distance. + + +Alternate Routing Tables +======================== + +TBD + +Alternate routing tables are used with policy based routing of by utilizing +:ref:`vrf`. + + +.. _routing-arp: + +### +ARP +### + +:abbr:`ARP (Address Resolution Protocol)` is a communication protocol used for +discovering the link layer address, such as a MAC address, associated with a +given internet layer address, typically an IPv4 address. This mapping is a +critical function in the Internet protocol suite. ARP was defined in 1982 by +:rfc:`826` which is Internet Standard STD 37. + +In Internet Protocol Version 6 (IPv6) networks, the functionality of ARP is +provided by the Neighbor Discovery Protocol (NDP). + +To manipulate or display ARP_ table entries, the following commands are +implemented. + +Configure +========= + +.. cfgcmd:: set protocols static arp <address> hwaddr <mac> + + This will configure a static ARP entry always resolving `<address>` to + `<mac>`. + + Example: + + .. code-block:: none + + set protocols static arp 192.0.2.100 hwaddr 00:53:27:de:23:aa + +Operation +========= + +.. opcmd:: show protocols static arp + + Display all known ARP table entries spanning across all interfaces + +.. code-block:: none + + vyos@vyos:~$ show protocols static arp + Address HWtype HWaddress Flags Mask Iface + 10.1.1.1 ether 00:53:00:de:23:2e C eth1 + 10.1.1.100 ether 00:53:00:de:23:aa CM eth1 + + +.. opcmd:: show protocols static arp interface eth1 + + Display all known ARP table entries on a given interface only (`eth1`): + +.. code-block:: none + + vyos@vyos:~$ show protocols static arp interface eth1 + Address HWtype HWaddress Flags Mask Iface + 10.1.1.1 ether 00:53:00:de:23:2e C eth1 + 10.1.1.100 ether 00:53:00:de:23:aa CM eth1 + +.. _ARP: https://en.wikipedia.org/wiki/Address_Resolution_Protocol |