diff options
Diffstat (limited to 'docs/configuration/protocols')
| -rw-r--r-- | docs/configuration/protocols/mpls.rst | 14 | ||||
| -rw-r--r-- | docs/configuration/protocols/ospf.rst | 17 |
2 files changed, 17 insertions, 14 deletions
diff --git a/docs/configuration/protocols/mpls.rst b/docs/configuration/protocols/mpls.rst index d1d0cd87..550473d7 100644 --- a/docs/configuration/protocols/mpls.rst +++ b/docs/configuration/protocols/mpls.rst @@ -27,12 +27,14 @@ network transport of data packets. For more information on how MPLS label switching works, please go visit `Wikipedia (MPLS)`_. -.. note:: MPLS support in VyOS is not finished yet, and therefore its - functionality is limited. Currently there is no support for MPLS enabled VPN - services such as L3VPNs, L2VPNs, and mVPNs. RSVP support is also not present - as the underlying routing stack (FRR) does not implement it. Currently VyOS - can be configured as a label switched router (MPLS P router), in both - penultimate and ultimate hop popping operations. +.. note:: MPLS support in VyOS is not finished yet, and therefore its + functionality is limited. Currently there is no support for MPLS enabled VPN + services such as L2VPNs and mVPNs. RSVP support is also not present as the + underlying routing stack (FRR) does not implement it. Currently VyOS + implements LDP as described in RFC 5036; other LDP standard are the + following ones: RFC 6720, RFC 6667, RFC 5919, RFC 5561, RFC 7552, RFC 4447. + Because MPLS is already available (FRR also supports RFC 3031). + Label Distribution Protocol =========================== diff --git a/docs/configuration/protocols/ospf.rst b/docs/configuration/protocols/ospf.rst index e3f9759e..4949cded 100644 --- a/docs/configuration/protocols/ospf.rst +++ b/docs/configuration/protocols/ospf.rst @@ -43,7 +43,8 @@ starts when the first ospf enabled interface is configured. enable ospf on interface with address 192.168.1.1/23, but it does on interface with address 192.168.1.129/25. - In some cases it may be more convenient to enable OSPF on a per interface/subnet + In some cases it may be more convenient to enable OSPF on a per + interface/subnet basis :cfgcmd:`set protocols ospf interface <interface> area <x.x.x.x | x>` .. cfgcmd:: set protocols ospf auto-cost reference-bandwidth <number> @@ -790,7 +791,7 @@ General VyOS does not have a special command to start the OSPFv3 process. The OSPFv3 process starts when the first ospf enabled interface is configured. -.. cfgcmd:: set protocols ospfv3 area <number> interface <interface> +.. cfgcmd:: set protocols ospfv3 interface <interface> area <number> This command specifies the OSPFv3 enabled interface. This command is also used to enable the OSPF process. The area number can be specified in @@ -987,7 +988,7 @@ A typical configuration using 2 nodes. .. code-block:: none - set protocols ospfv3 area 0.0.0.0 interface eth1 + set protocols ospfv3 interface eth1 area 0.0.0.0 set protocols ospfv3 area 0.0.0.0 range 2001:db8:1::/64 set protocols ospfv3 parameters router-id 192.168.1.1 set protocols ospfv3 redistribute connected @@ -996,7 +997,7 @@ A typical configuration using 2 nodes. .. code-block:: none - set protocols ospfv3 area 0.0.0.0 interface eth1 + set protocols ospfv3 interface eth1 area 0.0.0.0 set protocols ospfv3 area 0.0.0.0 range 2001:db8:2::/64 set protocols ospfv3 parameters router-id 192.168.2.1 set protocols ospfv3 redistribute connected @@ -1025,8 +1026,8 @@ Example configuration for WireGuard interfaces: set interfaces wireguard wg01 peer ospf02 pubkey 'ie3...=' set interfaces wireguard wg01 port '12345' set protocols ospfv3 parameters router-id 192.168.1.1 - set protocols ospfv3 area 0.0.0.0 interface 'wg01' - set protocols ospfv3 area 0.0.0.0 interface 'lo' + set protocols ospfv3 interface 'wg01' area 0.0.0.0 + set protocols ospfv3 interface 'lo' area 0.0.0.0 **Node 2** @@ -1040,8 +1041,8 @@ Example configuration for WireGuard interfaces: set interfaces wireguard wg01 peer ospf01 pubkey 'NHI...=' set interfaces wireguard wg01 port '12345' set protocols ospfv3 parameters router-id 192.168.1.2 - set protocols ospfv3 area 0.0.0.0 interface 'wg01' - set protocols ospfv3 area 0.0.0.0 interface 'lo' + set protocols ospfv3 interface 'wg01' area 0.0.0.0 + set protocols ospfv3 interface 'lo' area 0.0.0.0 **Status** |