diff options
Diffstat (limited to 'docs/configuration/protocols')
| -rw-r--r-- | docs/configuration/protocols/ospf.rst | 28 |
1 files changed, 14 insertions, 14 deletions
diff --git a/docs/configuration/protocols/ospf.rst b/docs/configuration/protocols/ospf.rst index ccddcd92..8c858ce1 100644 --- a/docs/configuration/protocols/ospf.rst +++ b/docs/configuration/protocols/ospf.rst @@ -37,12 +37,12 @@ starts when the first ospf enabled interface is configured. This command is also used to enable the OSPF process. The area number can be specified in decimal notation in the range from 0 to 4294967295. Or it can be specified in dotted decimal notation similar to ip address. - + Prefix length in interface must be equal or bigger (i.e. smaller network) than prefix length in network statement. For example statement above doesn't enable ospf on interface with address 192.168.1.1/23, but it does on interface with address 192.168.1.129/25. - + In some cases it may be more convenient to enable OSPF on a per interface/subnet basis :cfgcmd:`set protocols ospf interface <interface> area <x.x.x.x | x>` @@ -549,12 +549,12 @@ Operational Mode Commands This command displays the neighbors information in a detailed form for a neighbor whose IP address is specified. -.. opcmd:: show ip ospf neighbor <intname> +.. opcmd:: show ip ospf neighbor <interface> This command displays the neighbors status for a neighbor on the specified interface. -.. opcmd:: show ip ospf interface [<intname>] +.. opcmd:: show ip ospf interface [<interface>] This command displays state and configuration of OSPF the specified interface, or all interfaces if no interface is given. @@ -826,20 +826,20 @@ Area Configuration Interface Configuration ----------------------- -.. cfgcmd:: set protocols ospfv3 interface <intname> ipv6 cost <number> +.. cfgcmd:: set protocols ospfv3 interface <interface> ipv6 cost <number> This command sets link cost for the specified interface. The cost value is set to router-LSA’s metric field and used for SPF calculation. The cost range is 1 to 65535. -.. cfgcmd:: set protocols ospfv3 interface <intname> dead-interval <number> +.. cfgcmd:: set protocols ospfv3 interface <interface> dead-interval <number> Set number of seconds for router Dead Interval timer value used for Wait Timer and Inactivity Timer. This value must be the same for all routers attached to a common network. The default value is 40 seconds. The interval range is 1 to 65535. -.. cfgcmd:: set protocols ospfv3 interface <intname> hello-interval +.. cfgcmd:: set protocols ospfv3 interface <interface> hello-interval <number> Set number of seconds for Hello Interval timer value. Setting this value, @@ -848,14 +848,14 @@ Interface Configuration common network. The default value is 10 seconds. The interval range is 1 to 65535. -.. cfgcmd:: set protocols ospfv3 interface <intname> mtu-ignore +.. cfgcmd:: set protocols ospfv3 interface <interface> mtu-ignore This command disables check of the MTU value in the OSPF DBD packets. Thus, use of this command allows the OSPF adjacency to reach the FULL state even though there is an interface MTU mismatch between two OSPF routers. -.. cfgcmd:: set protocols ospfv3 interface <intname> network <type> +.. cfgcmd:: set protocols ospfv3 interface <interface> network <type> This command allows to specify the distribution type for the network connected to this interface: @@ -863,20 +863,20 @@ Interface Configuration **broadcast** – broadcast IP addresses distribution. **point-to-point** – address distribution in point-to-point networks. -.. cfgcmd:: set protocols ospfv3 interface <intname> priority <number> +.. cfgcmd:: set protocols ospfv3 interface <interface> priority <number> This command sets Router Priority integer value. The router with the highest priority will be more eligible to become Designated Router. Setting the value to 0, makes the router ineligible to become Designated Router. The default value is 1. The interval range is 0 to 255. -.. cfgcmd:: set protocols ospfv3 interface <intname> passive +.. cfgcmd:: set protocols ospfv3 interface <interface> passive This command specifies interface as passive. Passive interface advertises its address, but does not run the OSPF protocol (adjacencies are not formed and hello packets are not generated). -.. cfgcmd:: set protocols ospfv3 interface <intname> retransmit-interval +.. cfgcmd:: set protocols ospfv3 interface <interface> retransmit-interval <number> This command sets number of seconds for RxmtInterval timer value. This @@ -884,7 +884,7 @@ Interface Configuration Request packets if acknowledge was not received. The default value is 5 seconds. The interval range is 3 to 65535. -.. cfgcmd:: set protocols ospfv3 interface <intname> transmit-delay +.. cfgcmd:: set protocols ospfv3 interface <interface> transmit-delay <number> This command sets number of seconds for InfTransDelay value. It allows to @@ -927,7 +927,7 @@ Operational Mode Commands This command displays the neighbor DR choice information. -.. opcmd:: show ipv6 ospfv3 interface [prefix]|[<intname> [prefix]] +.. opcmd:: show ipv6 ospfv3 interface [prefix]|[<interface> [prefix]] This command displays state and configuration of OSPF the specified interface, or all interfaces if no interface is given. Whith the argument |