diff options
Diffstat (limited to 'docs/configuration/service/ipoe-server.rst')
| -rw-r--r-- | docs/configuration/service/ipoe-server.rst | 476 |
1 files changed, 367 insertions, 109 deletions
diff --git a/docs/configuration/service/ipoe-server.rst b/docs/configuration/service/ipoe-server.rst index ed4ade1a..5608c27c 100644 --- a/docs/configuration/service/ipoe-server.rst +++ b/docs/configuration/service/ipoe-server.rst @@ -1,5 +1,3 @@ -.. include:: /_include/need_improvement.txt - .. _ipoe_server: ########### @@ -24,8 +22,9 @@ functionality as PPPoE, but in a less robust manner. will restart the ppp daemon and will reset existing IPoE sessions, in order to become effective. -Configuration -============= +*********************** +Configuring IPoE Server +*********************** IPoE can be configure on different interfaces, it will depend on each specific situation which interface will provide IPoE to clients. The clients mac address @@ -39,158 +38,417 @@ the configuration. .. code-block:: none - set service ipoe-server authentication interface eth2 mac 08:00:27:2f:d8:06 - set service ipoe-server authentication mode 'local' - set service ipoe-server name-server '10.10.1.1' - set service ipoe-server name-server '10.10.1.2' - set service ipoe-server interface eth2 client-subnet '192.168.0.0/24' + set interfaces ethernet eth1 address '192.168.0.1/24' + set service ipoe-server authentication interface eth1.100 mac 00:50:79:66:68:00 + set service ipoe-server authentication interface eth1.101 mac 00:50:79:66:68:01 + set service ipoe-server authentication mode 'local' + set service ipoe-server client-ip-pool IPOE-POOL range '192.168.0.2-192.168.0.254' + set service ipoe-server default-pool 'IPOE-POOL' + set service ipoe-server gateway-address '192.168.0.1/24' + set service ipoe-server interface eth1 mode 'l2' + set service ipoe-server interface eth1 network 'vlan' + set service ipoe-server interface eth1 vlan '100-200' -The first address of the parameter ``client-subnet``, will be used as the -default gateway. Connected sessions can be checked via the ``show ipoe-server -sessions`` command. +.. cfgcmd:: set service ipoe-server authentication interface <interface> mac <MAC> -.. code-block:: none + Creates local pppoe user with username=**<interface>** and + password=**<MAC>** (mac-address) - vyos@vyos:~$ show ipoe-server sessions +.. cfgcmd:: set service ipoe-server authentication mode <local | radius> - ifname | called-sid | calling-sid | ip | ip6 | ip6-dp | rate-limit | state | uptime | sid - -------+------------+-------------------+-------------+-----+--------+------------+--------+----------+------------------ - ipoe0 | eth2 | 08:00:27:2f:d8:06 | 192.168.0.2 | | | | active | 00:45:05 | dccc870fd3134612 + Set authentication backend. The configured authentication backend is used + for all queries. + * **radius**: All authentication queries are handled by a configured RADIUS + server. + * **local**: All authentication queries are handled locally. + * **noauth**: Authentication disabled -IPv6 SLAAC and IA-PD --------------------- +.. cfgcmd:: set service ipoe-server client-ip-pool <POOL-NAME> range <x.x.x.x-x.x.x.x | x.x.x.x/x> -To configure IPv6 assignments for clients, two options need to be configured. -A global prefix which is terminated on the clients cpe and a delegated prefix, -the client can use for devices routed via the clients cpe. + Use this command to define the first IP address of a pool of + addresses to be given to l2tp clients. If notation ``x.x.x.x-x.x.x.x``, + it must be within a /24 subnet. If notation ``x.x.x.x/x`` is + used there is possibility to set host/netmask. -IPv6 DNS addresses are optional. +.. cfgcmd:: set service ipoe-server default-pool <POOL-NAME> -.. code-block:: none + Use this command to define default address pool name. - set service ipoe-server authentication interface eth3 mac 08:00:27:2F:D8:06 - set service ipoe-server authentication mode 'local' - set service ipoe-server client-ipv6-pool IPv6-POOL delegate '2001:db8:1::/48' delegation-prefix '56' - set service ipoe-server client-ipv6-pool IPv6-POOL prefix '2001:db8::/48' mask '64' - set service ipoe-server default-ipv6-pool IPv6-POOL - set service ipoe-server name-server '2001:db8::' - set service ipoe-server name-server '2001:db8:aaa::' - set service ipoe-server name-server '2001:db8:bbb::' - set service ipoe-server interface eth3 client-subnet '192.168.1.0/24' +.. cfgcmd:: set service ipoe-server gateway-address <x.x.x.x/x> + + Specifies address to be used as server ip address if radius can assign + only client address. In such case if client address is matched network + and mask then specified address and mask will be used. You can specify + multiple such options. + +.. cfgcmd:: set service ipoe-server interface <interface> mode <l2 | l3> + + Set authentication backend. The configured authentication backend is used + for all queries. + + * **l2**: It means that clients are on same network where interface + is.**(default)** + * **local**: It means that client are behind some router. + +.. cfgcmd:: set service ipoe-server interface <interface> network <shared | vlan> + + Specify where interface is shared by multiple users or it is vlan-per-user. + + * **shared**: Multiple clients share the same network. **(default)** + * **vlan**: One VLAN per client. .. code-block:: none - vyos@ipoe-server# run sh ipoe-server sessions - ifname | called-sid | calling-sid | ip | ip6 | ip6-dp | rate-limit | state | uptime | sid - -------+------------+-------------------+-------------+---------------------------------+-----------------+------------+--------+----------+------------------ - ipoe0 | eth3 | 08:00:27:2f:d8:06 | 192.168.1.2 | 2001:db8::a00:27ff:fe2f:d806/64 | 2001:db8:1::/56 | | active | 01:02:59 | 4626faf71b12cc25 + vyos@vyos:~$ show ipoe-server sessions + ifname | username | calling-sid | ip | rate-limit | type | comp | state | uptime + --------+----------+-------------------+-------------+------------+------+------+--------+---------- + ipoe0 | eth1.100 | 00:50:79:66:68:00 | 192.168.0.2 | | ipoe | | active | 00:04:55 + ipoe1 | eth1.101 | 00:50:79:66:68:01 | 192.168.0.3 | | ipoe | | active | 00:04:44 -The clients :abbr:`CPE (Customer Premises Equipment)` can now communicate via -IPv4 or IPv6. All devices behind ``2001:db8::a00:27ff:fe2f:d806/64`` can use -addresses from ``2001:db8:1::/56`` and can globally communicate without the -need of any NAT rules. -Automatic VLAN creation ------------------------ +********************************* +Configuring RADIUS authentication +********************************* -To create VLANs per user during runtime, the following settings are required on -a per interface basis. VLAN ID and VLAN range can be present in the -configuration at the same time. +To enable RADIUS based authentication, the authentication mode needs to be +changed within the configuration. Previous settings like the local users, still +exists within the configuration, however they are not used if the mode has been +changed from local to radius. Once changed back to local, it will use all local +accounts again. .. code-block:: none - set service ipoe-server interface eth2 network vlan - set service ipoe-server interface eth2 vlan-id 100 - set service ipoe-server interface eth2 vlan-id 200 - set service ipoe-server interface eth2 vlan-range 1000-2000 - set service ipoe-server interface eth2 vlan-range 2500-2700 + set service ipoe-server authentication mode radius + +.. cfgcmd:: set service ipoe-server authentication radius server <server> key <secret> -RADIUS Setup ------------- + Configure RADIUS `<server>` and its required shared `<secret>` for + communicating with the RADIUS server. -To use a RADIUS server for authentication and bandwidth-shaping, the following -example configuration can be used. +Since the RADIUS server would be a single point of failure, multiple RADIUS +servers can be setup and will be used subsequentially. +For example: .. code-block:: none - set service ipoe-server authentication mode 'radius' - set service ipoe-server authentication radius server 10.100.100.1 key 'password' + set service ipoe-server authentication radius server 10.0.0.1 key 'foo' + set service ipoe-server authentication radius server 10.0.0.2 key 'foo' -Bandwidth Shaping -================= +.. note:: Some RADIUS severs use an access control list which allows or denies + queries, make sure to add your VyOS router to the allowed client list. -Bandwidth rate limits can be set for local users within the configuration or -via RADIUS based attributes. +RADIUS source address +===================== -Bandwidth Shaping for local users ---------------------------------- +If you are using OSPF as IGP, always the closest interface connected to the +RADIUS server is used. With VyOS 1.2 you can bind all outgoing RADIUS requests +to a single source IP e.g. the loopback interface. -The rate-limit is set in kbit/sec. +.. cfgcmd:: set service ipoe-server authentication radius source-address <address> -.. code-block:: none + Source IPv4 address used in all RADIUS server queires. + +.. note:: The ``source-address`` must be configured on one of VyOS interface. + Best practice would be a loopback or dummy interface. + +RADIUS advanced options +======================= + +.. cfgcmd:: set service ipoe-server authentication radius server <server> port <port> + + Configure RADIUS `<server>` and its required port for authentication requests. + +.. cfgcmd:: set service ipoe-server authentication radius server <server> fail-time <time> + + Mark RADIUS server as offline for this given `<time>` in seconds. + +.. cfgcmd:: set service ipoe-server authentication radius server <server> disable + + Temporary disable this RADIUS server. + +.. cfgcmd:: set service ipoe-server authentication radius acct-timeout <timeout> + + Timeout to wait reply for Interim-Update packets. (default 3 seconds) + +.. cfgcmd:: set service ipoe-server authentication radius dynamic-author server <address> + + Specifies IP address for Dynamic Authorization Extension server (DM/CoA) + +.. cfgcmd:: set service ipoe-server authentication radius dynamic-author port <port> + + Port for Dynamic Authorization Extension server (DM/CoA) + +.. cfgcmd:: set service ipoe-server authentication radius dynamic-author key <secret> + + Secret for Dynamic Authorization Extension server (DM/CoA) + +.. cfgcmd:: set service ipoe-server authentication radius max-try <number> + + Maximum number of tries to send Access-Request/Accounting-Request queries + +.. cfgcmd:: set service ipoe-server authentication radius timeout <timeout> + + Timeout to wait response from server (seconds) + +.. cfgcmd:: set service ipoe-server authentication radius nas-identifier <identifier> + + Value to send to RADIUS server in NAS-Identifier attribute and to be matched + in DM/CoA requests. + +.. cfgcmd:: set service ipoe-server authentication radius nas-ip-address <address> + + Value to send to RADIUS server in NAS-IP-Address attribute and to be matched + in DM/CoA requests. Also DM/CoA server will bind to that address. + +.. cfgcmd:: set service ipoe-server authentication radius source-address <address> + + Source IPv4 address used in all RADIUS server queires. + +.. cfgcmd:: set service ipoe-server authentication radius rate-limit attribute <attribute> + + Specifies which RADIUS server attribute contains the rate limit information. + The default attribute is `Filter-Id`. + +.. note:: If you set a custom RADIUS attribute you must define it on both + dictionaries at RADIUS server and client. + +.. cfgcmd:: set service ipoe-server authentication radius rate-limit enable + + Enables bandwidth shaping via RADIUS. + +.. cfgcmd:: set service ipoe-server authentication radius rate-limit vendor + + Specifies the vendor dictionary, dictionary needs to be in + /usr/share/accel-ppp/radius. + +Received RADIUS attributes have a higher priority than parameters defined within +the CLI configuration, refer to the explanation below. + +Allocation clients ip addresses by RADIUS +========================================= + +If the RADIUS server sends the attribute ``Framed-IP-Address`` then this IP +address will be allocated to the client and the option ``default-pool`` within the CLI +config is being ignored. + +If the RADIUS server sends the attribute ``Framed-Pool``, IP address will be allocated +from a predefined IP pool whose name equals the attribute value. + +If the RADIUS server sends the attribute ``Stateful-IPv6-Address-Pool``, IPv6 address +will be allocated from a predefined IPv6 pool ``prefix`` whose name equals the attribute value. + +If the RADIUS server sends the attribute ``Delegated-IPv6-Prefix-Pool``, IPv6 +delegation pefix will be allocated from a predefined IPv6 pool ``delegate`` +whose name equals the attribute value. + +.. note:: ``Stateful-IPv6-Address-Pool`` and ``Delegated-IPv6-Prefix-Pool`` are defined in + RFC6911. If they are not defined in your RADIUS server, add new dictionary_. + +User interface can be put to VRF context via RADIUS Access-Accept packet, or change +it via RADIUS CoA. ``Accel-VRF-Name`` is used from these purposes. It is custom `ACCEL-PPP attribute`_. +Define it in your RADIUS server. - set service ipoe-server authentication interface eth2 mac 08:00:27:2f:d8:06 rate-limit download '500' - set service ipoe-server authentication interface eth2 mac 08:00:27:2f:d8:06 rate-limit upload '500' - set service ipoe-server authentication mode 'local' - set service ipoe-server name-server '10.10.1.1' - set service ipoe-server name-server '10.10.1.2' - set service ipoe-server interface eth2 client-subnet '192.168.0.0/24' +Renaming clients interfaces by RADIUS +===================================== + +If the RADIUS server uses the attribute ``NAS-Port-Id``, ppp tunnels will be +renamed. + +.. note:: The value of the attribute ``NAS-Port-Id`` must be less than 16 + characters, otherwise the interface won't be renamed. + +**** +IPv6 +**** + +.. cfgcmd:: set service ipoe-server client-ipv6-pool <IPv6-POOL-NAME> prefix <address> + mask <number-of-bits> + + Use this comand to set the IPv6 address pool from which an l2tp client + will get an IPv6 prefix of your defined length (mask) to terminate the + l2tp endpoint at their side. The mask length can be set from 48 to 128 + bit long, the default value is 64. + +.. cfgcmd:: set service ipoe-server client-ipv6-pool <IPv6-POOL-NAME> delegate <address> + delegation-prefix <number-of-bits> + + Use this command to configure DHCPv6 Prefix Delegation (RFC3633) on + l2tp. You will have to set your IPv6 pool and the length of the + delegation prefix. From the defined IPv6 pool you will be handing out + networks of the defined length (delegation-prefix). The length of the + delegation prefix can be set from 32 to 64 bit long. + +.. cfgcmd:: set service ipoe-server default-ipv6-pool <IPv6-POOL-NAME> + + Use this command to define default IPv6 address pool name. .. code-block:: none - vyos@vyos# run show ipoe-server sessions + set service ipoe-server client-ipv6-pool IPv6-POOL delegate '2001:db8:8003::/48' delegation-prefix '56' + set service ipoe-server client-ipv6-pool IPV6-POOL prefix '2001:db8:8002::/48' mask '64' + set service ipoe-server default-ipv6-pool IPv6-POOL + +********* +Scripting +********* + +.. cfgcmd:: set service ipoe-server extended-scripts on-change <path_to_script> + + Script to run when session interface changed by RADIUS CoA handling + +.. cfgcmd:: set service ipoe-server extended-scripts on-down <path_to_script> + + Script to run when session interface going to terminate + +.. cfgcmd:: set service ipoe-server extended-scripts on-pre-up <path_to_script> + + Script to run before session interface comes up + +.. cfgcmd:: set service ipoe-server extended-scripts on-up <path_to_script> + + Script to run when session interface is completely configured and started + +**************** +Advanced Options +**************** + +Authentication Advanced Options +=============================== + +.. cfgcmd:: set service ipoe-server authentication interface <interface> mac <MAC> vlan + <vlan-id> + + VLAN monitor for automatic creation of VLAN interfaces for specific user on specific <interface> + +.. cfgcmd:: set service ipoe-server authentication interface <interface> mac <MAC> rate-limit + download <bandwidth> + + Download bandwidth limit in kbit/s for user on interface `<interface>`. + +.. cfgcmd:: set service ipoe-server authentication interface <interface> mac <MAC> rate-limit + upload <bandwidth> + + Upload bandwidth limit in kbit/s for for user on interface `<interface>`. - ifname | called-sid | calling-sid | ip | ip6 | ip6-dp | rate-limit | state | uptime | sid - -------+------------+-------------------+-------------+-----+--------+------------+--------+----------+------------------ - ipoe0 | eth2 | 08:00:27:2f:d8:06 | 192.168.0.2 | | | 500/500 | active | 00:00:05 | dccc870fd31349fb +Client IP Pool Advanced Options +=============================== -Example -======= +.. cfgcmd:: set service ipoe-server client-ip-pool <POOL-NAME> next-pool <NEXT-POOL-NAME> -* IPoE server will listen on interfaces eth1.50 and eth1.51 -* There are rate-limited and non rate-limited users (MACs) + Use this command to define the next address pool name. -Server configuration --------------------- +Advanced Interface Options +============================== + +.. cfgcmd:: set service ipoe-server interface <interface> client-subnet <x.x.x.x/x> + + Specify local range of ip address to give to dhcp clients. First IP in range is router IP. + If you need more customization use `client-ip-pool` + +.. cfgcmd:: set service ipoe-server interface <interface> external-dhcp dhcp-relay <x.x.x.x> + + Specify DHCPv4 relay IP address to pass requests to. If specified giaddr is also needed. + +.. cfgcmd:: set service ipoe-server interface <interface> external-dhcp giaddr <x.x.x.x> + + Specifies relay agent IP addre + + +Global Advanced options +======================= + +.. cfgcmd:: set service ipoe-server description <description> + + Set description. + +.. cfgcmd:: set service ipoe-server limits burst <value> + + Burst count + +.. cfgcmd:: set service ipoe-server limits connection-limit <value> + + Acceptable rate of connections (e.g. 1/min, 60/sec) + +.. cfgcmd:: set service ipoe-server limits timeout <value> + + Timeout in seconds + +.. cfgcmd:: set service ipoe-server max-concurrent-sessions + + Maximum number of concurrent session start attempts + +.. cfgcmd:: set service ipoe-server name-server <address> + + Connected client should use `<address>` as their DNS server. This + command accepts both IPv4 and IPv6 addresses. Up to two nameservers + can be configured for IPv4, up to three for IPv6. + +.. cfgcmd:: set service ipoe-server shaper fwmark <1-2147483647> + + Match firewall mark value + +.. cfgcmd:: set service ipoe-server snmp master-agent + + Enable SNMP + +********** +Monitoring +********** .. code-block:: none - set interfaces dummy dum1000 address 100.64.0.1/32 - set interfaces dummy dum1000 address 2001:db8::1/128 + vyos@vyos:~$ show ipoe-server sessions + ifname | username | calling-sid | ip | rate-limit | type | comp | state | uptime + ----------+----------+-------------------+-------------+------------+------+------+--------+---------- + eth1.100 | eth1.100 | 0c:98:bd:b8:00:01 | 192.168.0.3 | | ipoe | | active | 03:03:58 - set interfaces ethernet eth1 description 'IPoE' - set interfaces ethernet eth1 vif 50 - set interfaces ethernet eth1 vif 51 +.. code-block:: none - set service ipoe-server authentication interface eth1.50 mac 00:0c:29:b7:49:a7 - set service ipoe-server authentication interface eth1.50 mac 00:0c:29:f0:be:4c rate-limit download '5000' - set service ipoe-server authentication interface eth1.50 mac 00:0c:29:f0:be:4c rate-limit upload '5000' - set service ipoe-server authentication interface eth1.51 mac 00:0c:29:b7:49:a7 rate-limit download '50000' - set service ipoe-server authentication interface eth1.51 mac 00:0c:29:b7:49:a7 rate-limit upload '50000' - set service ipoe-server authentication mode 'local' - - set service ipoe-server client-ipv6-pool IPv6-POOL delegate 2001:db8:ffff::/48 delegation-prefix '56' - set service ipoe-server client-ipv6-pool IPv6-POOL prefix 2001:db8:fffe::/48 mask '64' - set service ipoe-server default-ipv6-pool IPv6-POOL - set service ipoe-server interface eth1.50 client-subnet '100.64.50.0/24' - set service ipoe-server interface eth1.50 mode 'l2' - set service ipoe-server interface eth1.51 client-subnet '100.64.51.0/24' - set service ipoe-server interface eth1.51 mode 'l2' - set service ipoe-server name-server '100.64.0.1' - set service ipoe-server name-server '2001:db8::1' - -Client configuration --------------------- + vyos@vyos:~$ show ipoe-server statistics + uptime: 0.03:31:36 + cpu: 0% + mem(rss/virt): 6044/101360 kB + core: + mempool_allocated: 148628 + mempool_available: 144748 + thread_count: 1 + thread_active: 1 + context_count: 10 + context_sleeping: 0 + context_pending: 0 + md_handler_count: 6 + md_handler_pending: 0 + timer_count: 1 + timer_pending: 0 + sessions: + starting: 0 + active: 1 + finishing: 0 + ipoe: + starting: 0 + active: 1 + delayed: 0 + +************** +Toubleshooting +************** .. code-block:: none - set interfaces ethernet eth0 mac '00:0c:29:b7:49:a7' + vyos@vyos:~$sudo journalctl -u accel-ppp@ipoe -b 0 - set interfaces ethernet eth0 vif 50 address 'dhcp' - set interfaces ethernet eth0 vif 50 address 'dhcpv6' - set interfaces ethernet eth0 vif 50 dhcpv6-options pd 0 interface eth1 sla-id '1' + Feb 27 14:29:27 vyos accel-ipoe[2262]: eth1.100:: recv [DHCPv4 Discover xid=55df9228 chaddr=0c:98:bd:b8:00:01 <Message-Type Discover> <Request-IP 192.168.0.3> <Host-Name vyos> <Request-List Subnet,Broadcast,Router,DNS,Classless-Route,Domain-Name,MTU>] + Feb 27 14:29:27 vyos accel-ipoe[2262]: eth1.100:eth1.100: eth1.100: authentication succeeded + Feb 27 14:29:27 vyos accel-ipoe[2262]: eth1.100:eth1.100: send [DHCPv4 Offer xid=55df9228 yiaddr=192.168.0.4 chaddr=0c:98:bd:b8:00:01 <Message-Type Offer> <Server-ID 192.168.0.1> <Lease-Time 600> <T1 300> <T2 525> <Router 192.168.0.1> <Subnet 255.255.255.0>] + Feb 27 14:29:27 vyos accel-ipoe[2262]: eth1.100:eth1.100: recv [DHCPv4 Request xid=55df9228 chaddr=0c:98:bd:b8:00:01 <Message-Type Request> <Server-ID 192.168.0.1> <Request-IP 192.168.0.4> <Host-Name vyos> <Request-List Subnet,Broadcast,Router,DNS,Classless-Route,Domain-Name,MTU>] + Feb 27 14:29:27 vyos accel-ipoe[2262]: eth1.100:eth1.100: ipoe: activate session + Feb 27 14:29:27 vyos accel-ipoe[2262]: eth1.100:eth1.100: ipoe: no free IPv6 address + Feb 27 14:29:27 vyos accel-ipoe[2262]: eth1.100:eth1.100: ipoe: session started + Feb 27 14:29:27 vyos accel-ipoe[2262]: eth1.100:eth1.100: send [DHCPv4 Ack xid=55df9228 yiaddr=192.168.0.4 chaddr=0c:98:bd:b8:00:01 <Message-Type Ack> <Server-ID 192.168.0.1> <Lease-Time 600> <T1 300> <T2 525> <Router 192.168.0.1> <Subnet 255.255.255.0>] .. include:: /_include/common-references.txt +.. _dictionary: https://github.com/accel-ppp/accel-ppp/blob/master/accel-pppd/radius/dict/dictionary.rfc6911 +.. _`ACCEL-PPP attribute`: https://github.com/accel-ppp/accel-ppp/blob/master/accel-pppd/radius/dict/dictionary.accel
\ No newline at end of file |