diff options
Diffstat (limited to 'docs/configuration')
| -rw-r--r-- | docs/configuration/interfaces/wireguard.rst | 39 |
1 files changed, 19 insertions, 20 deletions
diff --git a/docs/configuration/interfaces/wireguard.rst b/docs/configuration/interfaces/wireguard.rst index db144650..0ceb0aa2 100644 --- a/docs/configuration/interfaces/wireguard.rst +++ b/docs/configuration/interfaces/wireguard.rst @@ -11,9 +11,9 @@ information. Configuration ============= -WireGuard requires the generation of a keypair, a private key which will -decrypt incoming traffic and a public key, which the peer(s) will use to -encrypt traffic. +WireGuard requires the generation of a keypair, which includes a private +key to decrypt incoming traffic, and a public key for peer(s) to encrypt +traffic. Generate keypair ---------------- @@ -26,8 +26,8 @@ Generate keypair .. opcmd:: show wireguard keypairs pubkey default - It shows the public key which needs to be shared with your peer(s). Your - peer will encrypt all traffic to your system using this public key. + It shows the public key to be shared with your peer(s). Your peer will + encrypt all traffic to your system using this public key. .. code-block:: none @@ -38,12 +38,11 @@ Generate keypair Generate named keypair ---------------------- -Named keypairs can be used on a interface basis, if configured. If +Named keypairs can be used on a interface basis when configured. If multiple WireGuard interfaces are being configured, each can have their own keypairs. -The commands below will generate 2 keypairs, which are not related to -each other. +The commands below generates 2 keypairs unrelated to each other. .. code-block:: none @@ -56,11 +55,11 @@ Interface configuration The next step is to configure your local side as well as the policy based trusted destination addresses. If you only initiate a connection, -the listen port and address/port is optional, if you however act as a server -and endpoints initiate the connections to your system, you need to -define a port your clients can connect to, otherwise it's randomly -chosen and may make it difficult with firewall rules, since the port may -be a different one when you reboot your system. +the listen port and address/port is optional; however, if you act as a +server and endpoints initiate the connections to your system, you need to +define a port your clients can connect to, otherwise the port is randomly +chosen and may make connection difficult with firewall rules, since the port +may be different each time the system is rebooted. You will also need the public key of your peer as well as the network(s) you want to tunnel (allowed-ips) to configure a WireGuard tunnel. The @@ -82,7 +81,7 @@ one. The last step is to define an interface route for 10.2.0.0/24 to get through the WireGuard interface `wg01`. Multiple IPs or networks can be -defined and routed, the last check is allowed-ips which either prevents +defined and routed. The last check is allowed-ips which either prevents or allows the traffic. .. note:: You can not assign the same allowed-ips statement to multiple @@ -116,7 +115,7 @@ the public key, which needs to be shared with the peer. set protocols static route 10.1.0.0/24 interface wg01 Assure that your firewall rules allow the traffic, in which case you -have a working VPN using WireGuard +have a working VPN using WireGuard. .. code-block:: none @@ -131,16 +130,16 @@ have a working VPN using WireGuard 64 bytes from 10.1.0.1: icmp_seq=2 ttl=64 time=1.02 ms An additional layer of symmetric-key crypto can be used on top of the -asymmetric crypto, which is optional. +asymmetric crypto. This is optional. .. code-block:: none wg01# run generate wireguard preshared-key rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc= -Copy the key, as it is not stored on the local file system. Make sure -you distribute that key in a safe manner, it's a symmetric key, so only -you and your peer should have knowledge of its content. +Copy the key, as it is not stored on the local filesystem. Because it +is a symmetric key, only you and your peer should have knowledge of +its content. Make sure you distribute the key in a safe manner, .. code-block:: none @@ -154,7 +153,7 @@ With WireGuard, a Road Warrior VPN config is similar to a site-to-site VPN. It just lacks the ``address`` and ``port`` statements. In the following example, the IPs for the remote clients are defined in -the peers. This would allow the peers to interact with one another. +the peers. This allows the peers to interact with one another. .. code-block:: none |