diff options
Diffstat (limited to 'docs/interfaces/vxlan.rst')
| -rw-r--r-- | docs/interfaces/vxlan.rst | 28 |
1 files changed, 14 insertions, 14 deletions
diff --git a/docs/interfaces/vxlan.rst b/docs/interfaces/vxlan.rst index ac818fcc..4b97c9e0 100644 --- a/docs/interfaces/vxlan.rst +++ b/docs/interfaces/vxlan.rst @@ -68,7 +68,7 @@ support this. Configuration commands ^^^^^^^^^^^^^^^^^^^^^^ -.. code-block:: sh +.. code-block:: console interfaces vxlan <vxlan[0-16777215]> @@ -97,7 +97,7 @@ This topology was built using GNS3. Topology: -.. code-block:: sh +.. code-block:: console Spine1: fa0/2 towards Leaf2, IP-address: 10.1.2.1/24 @@ -113,7 +113,7 @@ Topology: Spine1 Configuration: -.. code-block:: sh +.. code-block:: console conf t ip multicast-routing @@ -136,7 +136,7 @@ from. Leaf2 configuration: -.. code-block:: sh +.. code-block:: console set interfaces ethernet eth0 address '10.1.2.2/24' set protocols ospf area 0 network '10.0.0.0/8' @@ -161,7 +161,7 @@ Leaf2 configuration: Leaf3 configuration: -.. code-block:: sh +.. code-block:: console set interfaces ethernet eth0 address '10.1.3.3/24' set protocols ospf area 0 network '10.0.0.0/8' @@ -188,7 +188,7 @@ As you can see, Leaf2 and Leaf3 configuration is almost identical. There are lots of commands above, I'll try to into more detail below, command descriptions are placed under the command boxes: -.. code-block:: sh +.. code-block:: console set interfaces bridge br241 address '172.16.241.1/24' @@ -200,7 +200,7 @@ so that the Spine will learn how to reach it. To do this you need to change the OSPF network from '10.0.0.0/8' to '0.0.0.0/0' to allow 172.16/12-networks to be advertised. -.. code-block:: sh +.. code-block:: console set interfaces bridge br241 member interface 'eth1.241' set interfaces bridge br241 member interface 'vxlan241' @@ -208,28 +208,28 @@ advertised. Binds eth1.241 and vxlan241 to each other by making them both member interfaces of the same bridge. -.. code-block:: sh +.. code-block:: console set interfaces vxlan vxlan241 group '239.0.0.241' The multicast-group used by all Leafs for this vlan extension. Has to be the same on all Leafs that has this interface. -.. code-block:: sh +.. code-block:: console set interfaces vxlan vxlan241 link 'eth0' Sets the interface to listen for multicast packets on. Could be a loopback, not yet tested. -.. code-block:: sh +.. code-block:: console set interfaces vxlan vxlan241 vni '241' Sets the unique id for this vxlan-interface. Not sure how it correlates with multicast-address. -.. code-block:: sh +.. code-block:: console set interfaces vxlan vxlan241 remote-port 12345 @@ -244,7 +244,7 @@ Older Examples Example for bridging normal L2 segment and vxlan overlay network, and using a vxlan interface as routing interface. -.. code-block:: sh +.. code-block:: console interfaces { bridge br0 { @@ -276,7 +276,7 @@ router has a VLAN interface (26) facing the client devices and a VLAN interface can flow between both routers' VLAN 26, but can't escape since there is no L3 gateway. You can add an IP to a bridge to create a gateway. -.. code-block:: sh +.. code-block:: console interfaces { bridge br0 { @@ -310,7 +310,7 @@ Alternative to multicast, the remote IPv4 address of the VXLAN tunnel can set di Let's change the Multicast example from above: -.. code-block:: sh +.. code-block:: console # leaf2 and leaf3 delete interfaces vxlan vxlan241 group '239.0.0.241' |