diff options
Diffstat (limited to 'docs/operation')
| -rw-r--r-- | docs/operation/index.rst | 10 | ||||
| -rw-r--r-- | docs/operation/ip-commands.rst | 258 |
2 files changed, 268 insertions, 0 deletions
diff --git a/docs/operation/index.rst b/docs/operation/index.rst new file mode 100644 index 00000000..b40f769d --- /dev/null +++ b/docs/operation/index.rst @@ -0,0 +1,10 @@ +############## +Operation Mode +############## + +.. toctree:: + :maxdepth: 1 + :includehidden: + + information + ip-command
\ No newline at end of file diff --git a/docs/operation/ip-commands.rst b/docs/operation/ip-commands.rst new file mode 100644 index 00000000..eba4fd90 --- /dev/null +++ b/docs/operation/ip-commands.rst @@ -0,0 +1,258 @@ +.. _ip-commands: + +########### +IP commands +########### + +IPv4 +==== + +System configuration commands +----------------------------- + +.. cfgcmd:: set system ip disable-forwarding + + Use this command to disable IPv4 forwarding on all interfaces. + +.. cfgcmd:: set system ip arp table-size <number> + + Use this command to define the maximum number of entries to keep in + the ARP cache (1024, 2048, 4096, 8192, 16384, 32768). + +.. cfgcmd:: set system ip multipath layer4-hashing + + Use this command to use Layer 4 information for IPv4 ECMP hashing. + + +Operational commands +-------------------- + +show commands +^^^^^^^^^^^^^ + +See below the different parameters available for the IPv4 **show** command: + +.. code-block:: none + + vyos@vyos:~$ show ip + Possible completions: + access-list Show all IP access-lists + as-path-access-list + Show all as-path-access-lists + bgp Show Border Gateway Protocol (BGP) information + community-list + Show IP community-lists + extcommunity-list + Show extended IP community-lists + forwarding Show IP forwarding status + groups Show IP multicast group membership + igmp Show IGMP (Internet Group Management Protocol) information + large-community-list + Show IP large-community-lists + multicast Show IP multicast + ospf Show IPv4 Open Shortest Path First (OSPF) routing information + pim Show PIM (Protocol Independent Multicast) information + ports Show IP ports in use by various system services + prefix-list Show all IP prefix-lists + protocol Show IP route-maps per protocol + rip Show Routing Information Protocol (RIP) information + route Show IP routes + + +reset commands +^^^^^^^^^^^^^^ + +And the different IPv4 **reset** commands available: + +.. code-block:: none + + vyos@vyos:~$ reset ip + Possible completions: + arp Reset Address Resolution Protocol (ARP) cache + bgp Clear Border Gateway Protocol (BGP) statistics or status + igmp IGMP clear commands + multicast IP multicast routing table + route Reset IP route + +IPv6 +==== + +System configuration commands +----------------------------- + +.. cfgcmd:: set system ipv6 disable + + Use this command to disable assignment of IPv6 addresses on all + interfaces. + +.. cfgcmd:: set system ipv6 disable-forwarding + + Use this command to disable IPv6 forwarding on all interfaces. + +.. cfgcmd:: set system ipv6 neighbor table-size <number> + + Use this command to define the maximum number of entries to keep in + the Neighbor cache (1024, 2048, 4096, 8192, 16384, 32768). + +.. cfgcmd:: set system ipv6 strict-dad + + Use this command to disable IPv6 operation on interface when + Duplicate Address Detection fails on Link-Local address. + +.. cfgcmd:: set system ipv6 multipath layer4-hashing + + Use this command to user Layer 4 information for ECMP hashing. + + +Operational commands +-------------------- + +Show commands +^^^^^^^^^^^^^ + +.. opcmd:: show ipv6 neighbors + + Use this command to show IPv6 Neighbor Discovery Protocol information. + +.. opcmd:: show ipv6 groups + + Use this command to show IPv6 multicast group membership. + +.. opcmd:: show ipv6 forwarding + + Use this command to show IPv6 forwarding status. + +.. opcmd:: show ipv6 route + + Use this command to show IPv6 routes. + + Check the many parameters available for the `show ipv6 route` command: + + .. code-block:: none + + vyos@vyos:~$ show ipv6 route + Possible completions: + <Enter> Execute the current command + <X:X::X:X> Show IPv6 routes of given address or prefix + <X:X::X:X/M> + bgp Show IPv6 BGP routes + cache Show kernel IPv6 route cache + connected Show IPv6 connected routes + forward Show kernel IPv6 route table + isis Show IPv6 ISIS routes + kernel Show IPv6 kernel routes + ospfv3 Show IPv6 OSPF6 routes + ripng Show IPv6 RIPNG routes + static Show IPv6 static routes + summary Show IPv6 routes summary + table Show IP routes in policy table + vrf Show IPv6 routes in VRF + + +.. opcmd:: show ipv6 prefix-list + + Use this command to show all IPv6 prefix lists + + There are different parameters for getting prefix-list information: + + .. code-block:: none + + vyos@vyos:~$ show ipv6 prefix-list + Possible completions: + <Enter> Execute the current command + <WORD> Show specified IPv6 prefix-list + detail Show detail of IPv6 prefix-lists + summary Show summary of IPv6 prefix-lists + +.. opcmd:: show ipv6 access-list + + Use this command to show all IPv6 access lists + + You can also specify which IPv6 access-list should be shown: + + .. code-block:: none + + vyos@vyos:~$ show ipv6 access-list + Possible completions: + <Enter> Execute the current command + <text> Show specified IPv6 access-list + +.. opcmd:: show ipv6 bgp + + Use this command to show IPv6 Border Gateway Protocol information. + + + In addition, you can specify many other parameters to get BGP + information: + + .. code-block:: none + + vyos@vyos:~$ show ipv6 bgp + Possible completions: + <Enter> Execute the current command + <X:X::X:X> Show BGP information for given address or prefix + <X:X::X:X/M> + community Show routes matching the communities + community-list + Show routes matching the community-list + filter-list Show routes conforming to the filter-list + large-community + Show routes matching the large-community-list + large-community-list + neighbors Show detailed information on TCP and BGP neighbor connections + prefix-list Show routes matching the prefix-list + regexp Show routes matching the AS path regular expression + route-map Show BGP routes matching the specified route map + summary Show summary of BGP neighbor status + + +.. opcmd:: show ipv6 ospfv3 + + Use this command to get information about OSPFv3. + + You can get more specific OSPFv3 information by using the parameters + shown below: + + .. code-block:: none + + vyos@vyos:~$ show ipv6 ospfv3 + Possible completions: + <Enter> Execute the current command + area Show OSPFv3 spf-tree information + border-routers + Show OSPFv3 border-router (ABR and ASBR) information + database Show OSPFv3 Link state database information + interface Show OSPFv3 interface information + linkstate Show OSPFv3 linkstate routing information + neighbor Show OSPFv3 neighbor information + redistribute Show OSPFv3 redistribute External information + route Show OSPFv3 routing table information + +.. opcmd:: show ipv6 ripng + + Use this command to get information about the RIPNG protocol + +.. opcmd:: show ipv6 ripng status + + Use this command to show the status of the RIPNG protocol + + +Reset commands +^^^^^^^^^^^^^^ + +.. opcmd:: reset ipv6 bgp <address> + + Use this command to clear Border Gateway Protocol statistics or + status. + + +.. opcmd:: reset ipv6 neighbors <address | interface> + + Use this command to reset IPv6 Neighbor Discovery Protocol cache for + an address or interface. + +.. opcmd:: reset ipv6 route cache + + Use this command to flush the kernel IPv6 route cache. + An address can be added to flush it only for that route. + |