summaryrefslogtreecommitdiff
path: root/docs/services/pppoe-server.rst
diff options
context:
space:
mode:
Diffstat (limited to 'docs/services/pppoe-server.rst')
-rw-r--r--docs/services/pppoe-server.rst319
1 files changed, 221 insertions, 98 deletions
diff --git a/docs/services/pppoe-server.rst b/docs/services/pppoe-server.rst
index 29cadd16..e710ba6a 100644
--- a/docs/services/pppoe-server.rst
+++ b/docs/services/pppoe-server.rst
@@ -4,71 +4,79 @@
PPPoE Server
############
-VyOS utilizes `accel-ppp`_ to provide PPPoE server functionality. It can be
-used with local authentication or a connected RADIUS server.
+VyOS utilizes `accel-ppp`_ to provide PPPoE server functionality. It can
+be used with local authentication or a connected RADIUS server.
-.. note:: Please be aware, due to an upstream bug, config changes/commits
- will restart the ppp daemon and will reset existing PPPoE connections from
- connected users, in order to become effective.
+.. note:: Please be aware, due to an upstream bug, config
+ changes/commits will restart the ppp daemon and will reset existing
+ PPPoE connections from connected users, in order to become effective.
Configuration
=============
-The example below uses ACN as access-concentrator name, assigns an address
-from the pool 10.1.1.100-111, terminates at the local endpoint 10.1.1.1 and
-serves requests only on eth1.
-.. code-block:: none
+First steps
+-----------
- set service pppoe-server access-concentrator 'ACN'
- set service pppoe-server authentication local-users username foo password 'bar'
- set service pppoe-server authentication mode 'local'
- set service pppoe-server client-ip-pool start '10.1.1.100'
- set service pppoe-server client-ip-pool stop '10.1.1.111'
- set service pppoe-server dns-servers server-1 '10.100.100.1'
- set service pppoe-server dns-servers server-2 '10.100.200.1'
- set service pppoe-server interface 'eth1'
- set service pppoe-server local-ip '10.1.1.2'
+.. cfgcmd:: set service pppoe-server access-concentrator <name>
-Connections can be locally checked via the command
+ Use this command to set a name for this PPPoE-server access
+ concentrator.
-.. code-block:: none
+.. cfgcmd:: set service pppoe-server authentication mode <local | radius>
- show pppoe-server sessions
- ifname | username | ip | calling-sid | rate-limit | state | uptime | rx-bytes | tx-bytes
- -------+----------+------------+-------------------+-------------+--------+----------+----------+----------
- ppp0 | foo | 10.1.1.100 | 00:53:00:ba:db:15 | 20480/10240 | active | 00:00:11 | 214 B | 76 B
+ Use this command to define whether your PPPoE clients will locally
+ authenticate in your VyOS system or in RADIUS server.
+.. cfgcmd:: set service pppoe-server authentication local-users username <name> password <password>
-Per default the user session is being replaced if a second authentication
-request succeeds. Such session requests can be either denied or allowed
-entirely, which would allow multiple sessions for a user in the latter case.
-If it is denied, the second session is being rejected even if the
-authentication succeeds, the user has to terminate its first session and can
-then authentication again.
+ Use this command to configure the username and the password of a
+ locally configured user.
-.. code-block:: none
+.. cfgcmd:: set service pppoe-server interface <interface>
+
+ Use this command to define the interface the PPPoE server will use to
+ listen for PPPoE clients.
+
+.. cfgcmd:: set service pppoe-server local-ip <address>
+
+ Use this command to configure the local gateway IP address.
+
+.. cfgcmd:: set service pppoe-server name-server <address>
+
+ Use this command to set the IPv4 or IPv6 address of every Doman Name
+ Server you want to configure. They will be propagated to PPPoE
+ clients.
- vyos@# set service pppoe-server session-control
- Possible completions:
- disable Disables session control
- deny Deny second session authorization
Client Address Pools
--------------------
-To automatically assign the client an IP address as tunnel endpoint, a client
-IP pool is needed. The source can be either RADIUS or a local subnet or IP
-range definition.
+To automatically assign the client an IP address as tunnel endpoint, a
+client IP pool is needed. The source can be either RADIUS or a local
+subnet or IP range definition.
+
+Once the local tunnel endpoint ``set service pppoe-server local-ip
+'10.1.1.2'`` has been defined, the client IP pool can be either defined
+as a range or as subnet using CIDR notation. If the CIDR notation is
+used, multiple subnets can be setup which are used sequentially.
-Once the local tunnel endpoint ``set service pppoe-server local-ip '10.1.1.2'``
-has been defined, the client IP pool can be either defined as a range or as
-subnet using CIDR notation. If the CIDR notation is used, multiple subnets can
-be setup which are used sequentially.
**Client IP address via IP range definition**
+.. cfgcmd:: set service pppoe-server client-ip-pool start <address>
+
+ Use this command to define the first IP address of a pool of
+ addresses to be given to PPPoE clients. It must be within a /24
+ subnet.
+
+.. cfgcmd:: set service pppoe-server client-ip-pool stop <address>
+
+ Use this command to define the last IP address of a pool of
+ addresses to be given to PPPoE clients. It must be within a /24
+ subnet.
+
.. code-block:: none
set service pppoe-server client-ip-pool start '10.1.1.100'
@@ -77,6 +85,12 @@ be setup which are used sequentially.
**Client IP subnets via CIDR notation**
+.. cfgcmd:: set service pppoe-server client-ip-pool subnet <address>
+
+ Use this command for every pool of client IP addresses you want to
+ define. The addresses of this pool will be given to PPPoE clients.
+ You must use CIDR notation and it must be within a /24 subnet.
+
.. code-block:: none
set service pppoe-server client-ip-pool subnet '10.1.1.0/24'
@@ -84,63 +98,82 @@ be setup which are used sequentially.
set service pppoe-server client-ip-pool subnet '10.1.3.0/24'
-
**RADIUS based IP pools (Framed-IP-Address)**
-To use a radius server, you need to switch to authentication mode radius and
-of course need to specify an IP for the server. You can have multiple RADIUS
-server configured, if you wish to achieve redundancy.
+To use a radius server, you need to switch to authentication mode RADIUS
+and then configure it.
+
+.. cfgcmd:: set service pppoe-server authentication radius server <address> key <secret>
+
+ Use this command to configure the IP address and the shared secret
+ key of your RADIUS server. You can have multiple RADIUS servers
+ configured if you wish to achieve redundancy.
+
.. code-block:: none
set service pppoe-server access-concentrator 'ACN'
set service pppoe-server authentication mode 'radius'
- set service pppoe-server authentication radius-server 10.1.100.1 secret 'secret'
+ set service pppoe-server authentication radius server 10.1.100.1 key 'secret'
set service pppoe-server interface 'eth1'
set service pppoe-server local-ip '10.1.1.2'
-RADIUS provides the IP addresses in the example above via Framed-IP-Address.
+RADIUS provides the IP addresses in the example above via
+Framed-IP-Address.
**RADIUS sessions management DM/CoA**
-For remotely disconnect sessions and change some authentication parameters you
-can configure dae-server
+.. cfgcmd:: set service pppoe-server authentication radius dynamic-author <key | port | server>
+
+ Use this command to configure Dynamic Authorization Extensions to
+ RADIUS so that you can remotely disconnect sessions and change some
+ authentication parameters.
.. code-block:: none
- set service pppoe-server authentication radius-settings dae-server ip-address '10.1.1.2'
- set service pppoe-server authentication radius-settings dae-server port '3799'
- set service pppoe-server authentication radius-settings dae-server secret 'secret123'
+ set service pppoe-server authentication radius dynamic-author key 'secret123'
+ set service pppoe-server authentication radius dynamic-author port '3799'
+ set service pppoe-server authentication radius dynamic-author server '10.1.1.2'
-Example, from radius-server send command for disconnect client with username test
+
+Example, from radius-server send command for disconnect client with
+username test
.. code-block:: none
root@radius-server:~# echo "User-Name=test" | radclient -x 10.1.1.2:3799 disconnect secret123
-You can also use another attributes for identify client for disconnect, like
-Framed-IP-Address, Acct-Session-Id, etc. Result commands appears in log
+You can also use another attributes for identify client for disconnect,
+like Framed-IP-Address, Acct-Session-Id, etc. Result commands appears in
+log.
.. code-block:: none
show log | match Disconnect*
-Example for changing rate-limit via RADIUS CoA
+Example for changing rate-limit via RADIUS CoA.
.. code-block:: none
echo "User-Name=test,Filter-Id=5000/4000" | radclient 10.1.1.2:3799 coa secret123
-Filter-Id=5000/4000 (means 5000Kbit down-stream rate and 4000Kbit up-stream rate)
-If attribute Filter-Id redefined, replace it in radius coa request
+Filter-Id=5000/4000 (means 5000Kbit down-stream rate and 4000Kbit
+up-stream rate) If attribute Filter-Id redefined, replace it in RADIUS
+CoA request.
Automatic VLAN Creation
-----------------------
-VLAN's can be created by accel-ppp on the fly via the use of a Kernel module
-named `vlan_mon`, which is monitoring incoming vlans and creates the necessary
-VLAN if required and allowed. VyOS supports the use of either VLAN ID's or
-entire ranges, both values can be defined at the same time for an interface.
+.. cfgcmd:: set service pppoe-server interface <interface> <vlan-id | vlan range> <text>
+
+ VLAN's can be created by accel-ppp on the fly via the use of a Kernel
+ module named `vlan_mon`, which is monitoring incoming vlans and
+ creates the necessary VLAN if required and allowed. VyOS supports the
+ use of either VLAN ID's or entire ranges, both values can be defined
+ at the same time for an interface. When configured, the PPPoE will
+ create the necessary VLANs when required. Once the user session has
+ been cancelled and the VLAN is not needed anymore, VyOS will remove
+ it again.
.. code-block:: none
@@ -150,20 +183,20 @@ entire ranges, both values can be defined at the same time for an interface.
set service pppoe-server interface eth3 vlan-range 2000-3000
-The pppoe-server will now create these VLANs if required and once the user
-session has been cancelled, and the VLAN is not necessary anymore, it will
-remove it again.
-
Bandwidth Shaping
-----------------
-Bandwidth rate limits can be set for local users or RADIUS based attributes.
+Bandwidth rate limits can be set for local users or RADIUS based
+attributes.
For Local Users
^^^^^^^^^^^^^^^
-The rate-limit is set in kbit/sec.
+.. cfgcmd:: set service pppoe-server authentication local-users username <name> rate-limit <download | upload>
+
+ Use this command to configure a data-rate limit to PPPOoE clients for
+ traffic download or upload. The rate-limit is set in kbit/sec.
.. code-block:: none
@@ -174,14 +207,14 @@ The rate-limit is set in kbit/sec.
set service pppoe-server authentication mode 'local'
set service pppoe-server client-ip-pool start '10.1.1.100'
set service pppoe-server client-ip-pool stop '10.1.1.111'
- set service pppoe-server dns-servers server-1 '10.100.100.1'
- set service pppoe-server dns-servers server-2 '10.100.200.1'
+ set service pppoe-server name-server '10.100.100.1'
+ set service pppoe-server name-server '10.100.200.1'
set service pppoe-server interface 'eth1'
set service pppoe-server local-ip '10.1.1.2'
-Once the user is connected, the user session is using the set limits and can be
-displayed via 'show pppoe-server sessions'.
+Once the user is connected, the user session is using the set limits and
+can be displayed via 'show pppoe-server sessions'.
.. code-block:: none
@@ -194,26 +227,32 @@ displayed via 'show pppoe-server sessions'.
For RADIUS users
^^^^^^^^^^^^^^^^
-The current attribute 'Filter-Id' is being used as default and can be setup
-within RADIUS:
+The current attribute 'Filter-Id' is being used as default and can be
+setup within RADIUS:
-Filter-Id=2000/3000 (means 2000Kbit down-stream rate and 3000Kbit up-stream rate)
+Filter-Id=2000/3000 (means 2000Kbit down-stream rate and 3000Kbit
+up-stream rate)
-The command below enables it, assuming the RADIUS connection has been setup and
-is working.
+The command below enables it, assuming the RADIUS connection has been
+setup and is working.
-.. code-block:: none
+.. cfgcmd:: set service pppoe-server authentication radius rate-limit enable
- set service pppoe-server authentication radius-settings rate-limit enable
+ Use this command to enable bandwidth shaping via RADIUS.
-Other attributes can be used, but they have to be in one of the dictionaries
-in /usr/share/accel-ppp/radius.
+Other attributes can be used, but they have to be in one of the
+dictionaries in */usr/share/accel-ppp/radius*.
Load Balancing
--------------
-There exist PPPoE server session balancing mechanisms based on PADO packet delays.
+
+.. cfgcmd:: set service pppoe-server pado-delay <number-of-ms> sessions <number-of-sessions>
+
+ Use this command to enable the delay of PADO (PPPoE Active Discovery
+ Offer) packets, which can be used as a session balancing mechanism
+ with other PPPoE servers.
.. code-block:: none
@@ -221,29 +260,113 @@ There exist PPPoE server session balancing mechanisms based on PADO packet delay
set service pppoe-server pado-delay 100 sessions '1000'
set service pppoe-server pado-delay 300 sessions '3000'
-First 499 session connects without delay. PADO packets will be delayed 50 ms for connection from 500 to 999, this trick allows other PPPoE servers send PADO faster and clients will connect to other servers. Last command says that this PPPoE server can serve only 3000 clients.
+In the example above, the first 499 sessions connect without delay. PADO
+packets will be delayed 50 ms for connection from 500 to 999, this trick
+allows other PPPoE servers send PADO faster and clients will connect to
+other servers. Last command says that this PPPoE server can serve only
+3000 clients.
+
+
+IPv6
+----
+
+IPv6 client's prefix assignment
+^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^
+
+.. cfgcmd:: set service pppoe-server client-ipv6-pool prefix <address> mask <number-of-bits>
+
+ Use this comand to set the IPv6 address pool from which a PPPoE
+ client will get an IPv6 prefix of your defined length (mask) to
+ terminate the PPPoE endpoint at their side. The mask length can be
+ set from 48 to 128 bit long, the default value is 64.
+
+
+IPv6 Prefix Delegation
+^^^^^^^^^^^^^^^^^^^^^^
+
+.. cfgcmd:: set service pppoe-server client-ipv6-pool delegate <address> delegation-prefix <number-of-bits>
+
+ Use this command to configure DHCPv6 Prefix Delegation (RFC3633). You
+ will have to set your IPv6 pool and the length of the delegation
+ prefix. From the defined IPv6 pool you will be handing out networks
+ of the defined length (delegation-prefix). The length of the
+ delegation prefix can be set from 32 to 64 bit long.
Maintenance mode
-----------------
+================
+
+.. opcmd:: set pppoe-server maintenance-mode <enable | disable>
+
+ For network maintenance, it's a good idea to direct users to a backup
+ server so that the primary server can be safely taken out of service.
+ It's possible to switch your PPPoE server to maintenance mode where
+ it maintains already established connections, but refuses new
+ connection attempts.
+
+
+Checking connections
+====================
+
+.. opcmd:: show pppoe-server sessions
+
+ Use this command to locally check the active sessions in the PPPoE
+ server.
-For network maintenance, it's a good idea to direct users to a backup server so that the primary server can be safely taken out of service. It's possible to switch your PPPoE server to maintenance mode where it maintains already established connections, but refuses new connection attempts.
.. code-block:: none
- vyos@vyos:~$ set pppoe-server maintenance-mode enable
+ show pppoe-server sessions
+ ifname | username | ip | calling-sid | rate-limit | state | uptime | rx-bytes | tx-bytes
+ -------+----------+------------+-------------------+-------------+--------+----------+----------+----------
+ ppp0 | foo | 10.1.1.100 | 00:53:00:ba:db:15 | 20480/10240 | active | 00:00:11 | 214 B | 76 B
+
-You can also cancel maintenance mode with the following command
+Per default the user session is being replaced if a second
+authentication request succeeds. Such session requests can be either
+denied or allowed entirely, which would allow multiple sessions for a
+user in the latter case. If it is denied, the second session is being
+rejected even if the authentication succeeds, the user has to terminate
+its first session and can then authentication again.
.. code-block:: none
- vyos@vyos:~$ set pppoe-server maintenance-mode cancel
+ vyos@# set service pppoe-server session-control
+ Possible completions:
+ disable Disables session control
+ deny Deny second session authorization
+
+
+
+
+
Examples
========
-Dual-Stack IPv4/IPv6 provisioning with PD
------------------------------------------
+IPv4
+----
+
+The example below uses ACN as access-concentrator name, assigns an
+address from the pool 10.1.1.100-111, terminates at the local endpoint
+10.1.1.1 and serves requests only on eth1.
+
+.. code-block:: none
+
+ set service pppoe-server access-concentrator 'ACN'
+ set service pppoe-server authentication local-users username foo password 'bar'
+ set service pppoe-server authentication mode 'local'
+ set service pppoe-server client-ip-pool start '10.1.1.100'
+ set service pppoe-server client-ip-pool stop '10.1.1.111'
+ set service pppoe-server interface eth1
+ set service pppoe-server local-ip '10.1.1.2'
+ set service pppoe-server name-server '10.100.100.1'
+ set service pppoe-server name-server '10.100.200.1'
+
+
+
+Dual-Stack IPv4/IPv6 provisioning with Prefix Delegation
+--------------------------------------------------------
The example below covers a dual-stack configuration via pppoe-server.
@@ -253,16 +376,16 @@ The example below covers a dual-stack configuration via pppoe-server.
set service pppoe-server authentication mode 'local'
set service pppoe-server client-ip-pool start '192.168.0.1'
set service pppoe-server client-ip-pool stop '192.168.0.10'
- set service pppoe-server client-ipv6-pool delegate-prefix '2001:db8:8003::1/48,56'
- set service pppoe-server client-ipv6-pool prefix '2001:db8:8002::1/48,64'
- set service pppoe-server dns-servers server-1 '8.8.8.8'
- set service pppoe-server dnsv6-servers server-1 '2001:4860:4860::8888'
+ set service pppoe-server client-ipv6-pool delegate '2001:db8:8003::/48' delegation-prefix '56'
+ set service pppoe-server client-ipv6-pool prefix '2001:db8:8002::/48' mask '64'
+ set service pppoe-server name-server '8.8.8.8'
+ set service pppoe-server name-server '2001:4860:4860::8888'
set service pppoe-server interface 'eth2'
set service pppoe-server local-ip '10.100.100.1'
-The client, once successfully authenticated, will receive an IPv4 and an IPv6
-/64 address, to terminate the pppoe endpoint on the client side and a /56
-subnet for the clients internal use.
+The client, once successfully authenticated, will receive an IPv4 and an
+IPv6 /64 address to terminate the pppoe endpoint on the client side and
+a /56 subnet for the clients internal use.
.. code-block:: none
generated by cgit v1.2.3 (git 2.39.1) at 2024-11-25 22:41:57 +0000