diff options
Diffstat (limited to 'docs/services')
| -rw-r--r-- | docs/services/conntrack.rst | 178 | ||||
| -rw-r--r-- | docs/services/dhcp-relay.rst | 165 | ||||
| -rw-r--r-- | docs/services/dhcp.rst | 138 | ||||
| -rw-r--r-- | docs/services/dhcpv6.rst | 305 | ||||
| -rw-r--r-- | docs/services/dns-forwarding.rst | 59 | ||||
| -rw-r--r-- | docs/services/dynamic-dns.rst | 152 | ||||
| -rw-r--r-- | docs/services/index.rst | 26 | ||||
| -rw-r--r-- | docs/services/lldp.rst | 97 | ||||
| -rw-r--r-- | docs/services/mdns-repeater.rst | 30 | ||||
| -rw-r--r-- | docs/services/pppoe-server.rst | 56 | ||||
| -rw-r--r-- | docs/services/references.rst | 13 | ||||
| -rw-r--r-- | docs/services/snmp.rst | 180 | ||||
| -rw-r--r-- | docs/services/ssh.rst | 150 | ||||
| -rw-r--r-- | docs/services/tftp.rst | 42 | ||||
| -rw-r--r-- | docs/services/udp-broadcast-relay.rst | 53 | ||||
| -rw-r--r-- | docs/services/webproxy.rst | 121 |
16 files changed, 1765 insertions, 0 deletions
diff --git a/docs/services/conntrack.rst b/docs/services/conntrack.rst new file mode 100644 index 00000000..27db622d --- /dev/null +++ b/docs/services/conntrack.rst @@ -0,0 +1,178 @@ +Conntrack +--------- + +One of the important features built on top of the Netfilter framework is +connection tracking. Connection tracking allows the kernel to keep track of all +logical network connections or sessions, and thereby relate all of the packets +which may make up that connection. NAT relies on this information to translate +all related packets in the same way, and iptables can use this information to +act as a stateful firewall. + +The connection state however is completely independent of any upper-level +state, such as TCP's or SCTP's state. Part of the reason for this is that when +merely forwarding packets, i.e. no local delivery, the TCP engine may not +necessarily be invoked at all. Even connectionless-mode transmissions such as +UDP, IPsec (AH/ESP), GRE and other tunneling protocols have, at least, a pseudo +connection state. The heuristic for such protocols is often based upon a preset +timeout value for inactivity, after whose expiration a Netfilter connection is +dropped. + +Each Netfilter connection is uniquely identified by a (layer-3 protocol, source +address, destination address, layer-4 protocol, layer-4 key) tuple. The layer-4 +key depends on the transport protocol; for TCP/UDP it is the port numbers, for +tunnels it can be their tunnel ID, but otherwise is just zero, as if it were +not part of the tuple. To be able to inspect the TCP port in all cases, packets +will be mandatorily defragmented. + +Configuration +^^^^^^^^^^^^^ + +.. code-block:: sh + + # Protocols only for which local conntrack entries will be synced (tcp, udp, icmp, sctp) + set service conntrack-sync accept-protocol + + # Queue size for listening to local conntrack events (in MB) + set service conntrack-sync event-listen-queue-size <int> + + # Protocol for which expect entries need to be synchronized. (all, ftp, h323, nfs, sip, sqlnet) + set service conntrack-sync expect-sync + + # Failover mechanism to use for conntrack-sync [REQUIRED] + set service conntrack-sync failover-mechanism + + set service conntrack-sync cluster group <string> + set service conntrack-sync vrrp sync-group <1-255> + + # IP addresses for which local conntrack entries will not be synced + set service conntrack-sync ignore-address ipv4 <x.x.x.x> + + # Interface to use for syncing conntrack entries [REQUIRED] + set service conntrack-sync interface <ifname> + + # Multicast group to use for syncing conntrack entries + set service conntrack-sync mcast-group <x.x.x.x> + + # Queue size for syncing conntrack entries (in MB) + set service conntrack-sync sync-queue-size <size> + +Example +^^^^^^^ +The next exemple is a simple configuration of conntrack-sync. + + +.. figure:: /_static/images/service_conntrack_sync-schema.png + :scale: 60 % + :alt: Conntrack Sync Example + + Conntrack Sync Example + +First of all, make sure conntrack is enabled by running + +.. code-block:: sh + + show conntrack table ipv4 + +If the table is empty and you have a warning message, it means conntrack is not +enabled. To enable conntrack, just create a NAT or a firewall rule. + +.. code-block:: sh + + set firewall state-policy established action accept + +You now should have a conntrack table + +.. code-block:: sh + + $ show conntrack table ipv4 + TCP state codes: SS - SYN SENT, SR - SYN RECEIVED, ES - ESTABLISHED, + FW - FIN WAIT, CW - CLOSE WAIT, LA - LAST ACK, + TW - TIME WAIT, CL - CLOSE, LI - LISTEN + + CONN ID Source Destination Protocol TIMEOUT + 1015736576 10.35.100.87:58172 172.31.20.12:22 tcp [6] ES 430279 + 1006235648 10.35.101.221:57483 172.31.120.21:22 tcp [6] ES 413310 + 1006237088 10.100.68.100 172.31.120.21 icmp [1] 29 + 1015734848 10.35.100.87:56282 172.31.20.12:22 tcp [6] ES 300 + 1015734272 172.31.20.12:60286 239.10.10.14:694 udp [17] 29 + 1006239392 10.35.101.221 172.31.120.21 icmp [1] 29 + +Now configure conntrack-sync service on ``router1`` **and** ``router2`` + +.. code-block:: sh + + set service conntrack-sync accept-protocol 'tcp,udp,icmp' + set service conntrack-sync event-listen-queue-size '8' + set service conntrack-sync failover-mechanism cluster group 'GROUP' # Or VRRP + set service conntrack-sync interface 'eth0' + set service conntrack-sync mcast-group '225.0.0.50' + set service conntrack-sync sync-queue-size '8' + +On the active router, you should have informations in the internal-cache of +conntrack-sync. The same current active connections number should be shown in +the external-cache of the standby router + +On active router run: + + +.. code-block:: sh + + $ show conntrack-sync statistics + + Main Table Statistics: + + cache internal: + current active connections: 10 + connections created: 8517 failed: 0 + connections updated: 127 failed: 0 + connections destroyed: 8507 failed: 0 + + cache external: + current active connections: 0 + connections created: 0 failed: 0 + connections updated: 0 failed: 0 + connections destroyed: 0 failed: 0 + + traffic processed: + 0 Bytes 0 Pckts + + multicast traffic (active device=eth0): + 868780 Bytes sent 224136 Bytes recv + 20595 Pckts sent 14034 Pckts recv + 0 Error send 0 Error recv + + message tracking: + 0 Malformed msgs 0 Lost msgs + + + + On standby router run: + + + $ show conntrack-sync statistics + + Main Table Statistics: + + cache internal: + current active connections: 0 + connections created: 0 failed: 0 + connections updated: 0 failed: 0 + connections destroyed: 0 failed: 0 + + cache external: + current active connections: 10 + connections created: 888 failed: 0 + connections updated: 134 failed: 0 + connections destroyed: 878 failed: 0 + + traffic processed: + 0 Bytes 0 Pckts + + multicast traffic (active device=eth0): + 234184 Bytes sent 907504 Bytes recv + 14663 Pckts sent 21495 Pckts recv + 0 Error send 0 Error recv + + message tracking: + 0 Malformed msgs 0 Lost msgs + diff --git a/docs/services/dhcp-relay.rst b/docs/services/dhcp-relay.rst new file mode 100644 index 00000000..c6bccb22 --- /dev/null +++ b/docs/services/dhcp-relay.rst @@ -0,0 +1,165 @@ + + +DHCP Relay +---------- + +If you want your router to forward DHCP requests to an external DHCP server +you can configure the system to act as a DHCP relay agent. The DHCP relay +agent works with IPv4 and IPv6 addresses. + +All interfaces used for the DHCP relay must be configured. See +https://wiki.vyos.net/wiki/Network_address_setup. + +DHCP relay example +^^^^^^^^^^^^^^^^^^ + +.. figure:: /_static/images/service_dhcp-relay01.png + :scale: 80 % + :alt: DHCP relay example + + DHCP relay example + +In this example the interfaces used for the DHCP relay are eth1 and eth2. The +router receives DHCP client requests on eth1 and relays them through eth2 to +the DHCP server at 10.0.1.4. + +Configuration +^^^^^^^^^^^^^ + +Enable DHCP relay for eth1 and eth2: + +.. code-block:: sh + + set service dhcp-relay interface eth1 + set service dhcp-relay interface eth2 + +Set the IP address of the DHCP server: + +.. code-block:: sh + + set service dhcp-relay server 10.0.1.4 + +The router should discard DHCP packages already containing relay agent +information to ensure that only requests from DHCP clients are forwarded: + +.. code-block:: sh + + set service dhcp-relay relay-options relay-agents-packets discard + +Commit the changes and show the results: + +.. code-block:: sh + + commit + show service dhcp-relay + interface eth1 + interface eth2 + server 10.0.1.4 + relay-options { + relay-agents-packets discard + } + +The DHCP relay agent can be restarted with: + +.. code-block:: sh + + restart dhcp relay-agent + +DHCPv6 relay example +^^^^^^^^^^^^^^^^^^^^ + +.. figure:: /_static/images/service_dhcpv6-relay01.png + :scale: 80 % + :alt: DHCPv6 relay example + + DHCPv6 relay example + +In this example DHCPv6 requests are received by the router on eth1 +(`listening interface`) and forwarded through eth2 (`upstream interface`) to +the external DHCPv6 server at 2001:db8:100::4. + +Configuration +************* + +Set eth1 to be the listening interface for the DHCPv6 relay: + +.. code-block:: sh + + set service dhcpv6-relay listen-interface eth1 + +Set eth2 to be the upstream interface and specify the IPv6 address of +the DHCPv6 server: + +.. code-block:: sh + + set service dhcpv6-relay upstream-interface eth2 address 2001:db8:100::4 + +Commit the changes and show results: + +.. code-block:: sh + + commit + show service dhcpv6-relay + listen-interface eth1 { + } + upstream-interface eth2 { + address 2001:db8:100::4 + } + +Show the current status of the DHCPv6 relay agent: + +.. code-block:: sh + + show dhcpv6 relay-agent status + +The DHCPv6 relay agent can be restarted with: + +.. code-block:: sh + + restart dhcpv6 relay-agent + +Additional parameters +^^^^^^^^^^^^^^^^^^^^^ + +DHCP relay agent options +************************ + +Set the maximum hop count before packets are discarded. Range 0...255, +default 10. + +* :code:`set service dhcp-relay relay-options hop-count 'count'` + +Set maximum size of DHCP packets including relay agent information. If a +DHCP packet size surpasses this value it will be forwarded without appending +relay agent information. Range 64...1400, default 576. + +* :code:`set service dhcp-relay relay-options max-size 'size'` + +Four policies for reforwarding DHCP packets exist: + +* **append:** The relay agent is allowed to append its own relay information + to a received DHCP packet, disregarding relay information already present in + the packet. + +* **discard:** Received packets which already contain relay information will + be discarded. + +* **forward:** All packets are forwarded, relay information already present + will be ignored. + +* **replace:** Relay information already present in a packet is stripped and + replaced with the router's own relay information set. + +* :code:`set service dhcp-relay relay-options relay-agents-packet 'policy'` + +DHCPv6 relay agent options +************************** + +Set maximum hop count before packets are discarded. Default: 10. + +* :code:`set service dhcpv6-relay max-hop-count 'count'` + +If this is set the relay agent will insert the interface ID. This option is +set automatically if more than one listening interfaces are in use. + +* :code:`set service dhcpv6-relay use-interface-id-option` diff --git a/docs/services/dhcp.rst b/docs/services/dhcp.rst new file mode 100644 index 00000000..0fc01f04 --- /dev/null +++ b/docs/services/dhcp.rst @@ -0,0 +1,138 @@ + +DHCP Server +----------- + +Multiple DHCP Servers can be run from a single machine. Each DHCP service is +identified by a `shared-network-name`. + +DHCP Server Example +^^^^^^^^^^^^^^^^^^^ + +In this example, we are offering address space in the 172.16.17.0/24 network, +which is on eth1, and pppoe0 is our connection to the internet. We are using +the network name `dhcpexample`. + +Prerequisites +^^^^^^^^^^^^^ + +Configuring the PPPoE interface is assumed to be done already, and appears +on `pppoe0` + +Interface Configuration +^^^^^^^^^^^^^^^^^^^^^^^ + +.. code-block:: sh + + set interface eth1 address 172.16.17.1/24 + +Multiple ranges can be defined and can contain holes. + +.. code-block:: sh + + set service dhcp-server shared-network-name dhcpexample authoritative + set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 default-router 172.16.17.1 + set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 dns-server 172.16.17.1 + set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 lease 86400 + set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 range 0 start 172.16.17.100 + set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 range 0 stop 172.16.17.199 + + +Explanation +^^^^^^^^^^^ + +* :code:`set service dhcp-server shared-network-name dhcpexample authoritative` + + This says that this device is the only DHCP server for this network. If other + devices are trying to offer DHCP leases, this machine will send 'DHCPNAK' to + any device trying to request an IP address that is + not valid for this network. + +* :code:`set service dhcp-server shared-network-name dhcpexample subnet + 172.16.17.0/24 default-router 172.16.17.1` + + This is a configuration parameter for the subnet, saying that as part of the + response, tell the client that I am the default router for this network + +* :code:`set service dhcp-server shared-network-name dhcpexample subnet + 172.16.17.0/24 dns-server 172.16.17.1` + + This is a configuration parameter for the subnet, saying that as part of the + response, tell the client that I am the DNS server for this network. If you + do not want to run a DNS server, you could also provide one of the public + DNS servers, such as google's. You can add multiple entries by repeating the + line. + +* :code:`set service dhcp-server shared-network-name dhcpexample subnet + 172.16.17.0/24 lease 86400` + + Assign the IP address to this machine for 24 hours. It is unlikely you'd need + to shorten this period, unless you are running a network with lots of devices + appearing and disappearing. + + +* :code:`set service dhcp-server shared-network-name dhcpexample subnet + 172.16.17.0/24 range 0 start 172.16.17.100` + + Make a range of addresses available for clients starting from .100 [...] + +* :code:`set service dhcp-server shared-network-name dhcpexample subnet + 172.16.17.0/24 range 0 stop 172.16.17.199` + + [...] and ending at .199 + + +Failover +^^^^^^^^ + +VyOS provides support for DHCP failover: + +.. code-block:: sh + + set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover local-address '192.168.0.1' + set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover name 'foo' + set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover peer-address '192.168.0.2' + +.. note:: `name` must be identical on both sides! + +The primary and secondary statements determines whether the server is +primary or secondary + +.. code-block:: sh + + set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover status 'primary' + +or + +.. code-block:: sh + + set service dhcp-server shared-network-name 'LAN' subnet '192.168.0.0/24' failover status 'secondary' + +.. note:: In order for the primary and the secondary DHCP server to keep + their lease tables in sync, they must be able to reach each other on TCP + port 647. If you have firewall rules in effect, adjust them accordingly. + +Static mappings MAC/IP +^^^^^^^^^^^^^^^^^^^^^^ + +.. code-block:: sh + + set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 static-mapping static-mapping-01 ip-address 172.16.17.10 + set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 static-mapping static-mapping-01 mac-address ff:ff:ff:ff:ff:ff + +DHCP server options +^^^^^^^^^^^^^^^^^^^^^^^^^ + +default-router (DHCP option 003) + :code:`set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 default-router <ROUTER-IP>` + +dns-server (DHCP option 006) + :code:`set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 dns-server <DNS-SERVER-IP>` + +domain-name Client domain name (DHCP option 015) + :code:`set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 domain-name "<DOMAIN-NAME>"` + +domain-search (DHCP option 119) + This option can be given multiple times if you need multiple search domains + :code:`set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 domain-search "<DOMAIN_NAME_1>"` + :code:`set service dhcp-server shared-network-name dhcpexample subnet 172.16.17.0/24 domain-search "<DOMAIN_NAME_2>"` + diff --git a/docs/services/dhcpv6.rst b/docs/services/dhcpv6.rst new file mode 100644 index 00000000..e70b3eba --- /dev/null +++ b/docs/services/dhcpv6.rst @@ -0,0 +1,305 @@ + +DHCPv6 server +------------- + +VyOS provides DHCPv6 server functionality which is described in this section. +In order to use the DHCPv6 server it has to be enabled first: + +.. code-block:: sh + + set service dhcpv6-server + +To restart the DHCPv6 server (operational mode): + +.. code-block:: sh + + restart dhcpv6 server + +To show the current status of the DHCPv6 server use: + +.. code-block:: sh + + show dhcpv6 server status + +Show statuses of all assigned leases: + +.. code-block:: sh + + show dhcpv6 server leases + +DHCPv6 server options +^^^^^^^^^^^^^^^^^^^^^ + +DHCPv6 server preference value +****************************** + +Clients receiving advertise messages from multiple servers choose the server +with the highest preference value. The range for this value is `0...255`. Set +a preference value for the DHCPv6 server: + +.. code-block:: sh + + set service dhcpv6-server preference <preference value> + +Delete a preference: + +.. code-block:: sh + + set service dhcpv6-server preference + +Show current preference: + +.. code-block:: sh + + show service dhcpv6-server preference + +Specify address lease time +************************** + +The default lease time for DHCPv6 leases is 24 hours. This can be changed by +supplying a `default-time`, `maximum-time` and `minimum-time` (all values in +seconds): + +.. code-block:: sh + + set service dhcpv6-server shared-network-name <name> subnet <ipv6net> lease-time {default <default-time> | maximum <maximum-time> | minimum <minimum-time>} + +Reset the custom lease times: + +.. code-block:: sh + + delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> lease-time {default | maximum | minimum} + +Show the current configuration: + +.. code-block:: sh + + show service dhcpv6-server shared-network-name <name> subnet <ipv6net> lease-time {default | maximum | minimum} + +Specify NIS domain +****************** + +A Network Information (NIS) domain can be set to be used for DHCPv6 clients: + +.. code-block:: sh + + set service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-domain <nis-domain-name> + +To Delete the NIS domain: + +.. code-block:: sh + + delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-domain <nis-domain-name> + +Show a configured NIS domain: + +.. code-block:: sh + + show service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-domain <nis-domain-name> + +Specify NIS+ domain +******************* + +The procedure to specify a Network Information Service Plus (NIS+) domain is +similar to the NIS domain one: + +.. code-block:: sh + + set service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-domain <nisplus-domain-name> + +To Delete the NIS+ domain: + +.. code-block:: sh + + delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-domain <nisplus-domain-name> + +Show a configured NIS domain: + + # show service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-domain <nisplus-domain-name> + +Specify NIS server address +************************** + +To specify a NIS server address for DHCPv6 clients: + +.. code-block:: sh + + set service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-server <IPv6 address> + +Delete a specified NIS server address: + +.. code-block:: sh + + delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-server <IPv6 address> + +Show specified NIS server addresses: + +.. code-block:: sh + + show service dhcpv6-server shared-network-name <name> subnet <ipv6net> nis-server + +Specify NIS+ server address +*************************** + +To specify a NIS+ server address for DHCPv6 clients: + +.. code-block:: sh + + set service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-server <IPv6 address> + +Delete a specified NIS+ server address: + +.. code-block:: sh + + delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-server <IPv6 address> + +Show specified NIS+ server addresses: + +.. code-block:: sh + + show service dhcpv6-server shared-network-name <name> subnet <ipv6net> nisplus-server + +Specify a SIP server address for DHCPv6 clients +*********************************************** + +By IPv6 address +############### + + +A Session Initiation Protocol (SIP) server address can be specified +for DHCPv6 clients: + +.. code-block:: sh + + set service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-address <IPv6 address> + +Delete a specified SIP server address: + +.. code-block:: sh + + delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-address <IPv6 address> + +Show specified SIP server addresses: + +.. code-block:: sh + + show service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-address + +By FQDN +####### + +A name for SIP server can be specified: + +.. code-block:: sh + + set service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-name <sip-server-name> + +Delete a specified SIP server name: + +.. code-block:: sh + + delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-name <sip-server-name> + +Show specified SIP server names: + +.. code-block:: sh + + show service dhcpv6-server shared-network-name <name> subnet <ipv6net> sip-server-name + +Simple Network Time Protocol (SNTP) server address for DHCPv6 clients +********************************************************************* + +A SNTP server address can be specified for DHCPv6 clients: + +.. code-block:: sh + + set service dhcpv6-server shared-network-name <name> subnet <ipv6net> sntp-server-address <IPv6 address> + +Delete a specified SNTP server address: + +.. code-block:: sh + + delete service dhcpv6-server shared-network-name <name> subnet <ipv6net> sntp-server-address <IPv6 address> + +Show specified SNTP server addresses: + +.. code-block:: sh + + show service dhcpv6-server shared-network-name <name> subnet <ipv6net> sntp-server-address + +DHCPv6 address pools +^^^^^^^^^^^^^^^^^^^^ + +DHCPv6 address pools must be configured for the system to act as a DHCPv6 +server. The following example describes a common scenario. + +Example 1: DHCPv6 address pool +****************************** + +A shared network named `NET1` serves subnet `2001:db8:100::/64` which is +connected to `eth1`, a DNS server at `2001:db8:111::111` is used for name +services. The range of the address pool shall be `::100` through `::199`. The +lease time will be left at the default value which is 24 hours. + +.. code-block:: sh + + set service dhcpv6-server shared-network-name NET1 subnet 2001:db8:100::/64 address-range start 2001:db8:100::100 stop 2001:db8:100::199 + set service dhcpv6-server shared-network-name NET1 subnet 2001:db8:100::/64 name-server 2001:db8:111::111 + +Commit the changes and show the configuration: + +.. code-block:: sh + + commit + show service dhcpv6-server + shared-network-name NET1 { + subnet 2001:db8:100::/64 { + address-range { + start 2001:db8:100::100 { + stop 2001:db8:100::199 + } + } + name-server 2001:db8:111::111 + } + } + +Static mappings +^^^^^^^^^^^^^^^ + +In order to map specific IPv6 addresses to specific hosts static mappings can +be created. The following example explains the process. + +Example 1: Static IPv6 MAC-based mapping +**************************************** + +IPv6 address `2001:db8:100::101` shall be statically mapped to a device with +MAC address `00:15:c5:b7:5e:23`, this host-specific mapping shall be named +`client1`. + +.. note:: The MAC address identifier is defined by the last 4 byte of the + MAC address. + +.. code-block:: sh + + set service dhcpv6-server shared-network-name NET1 subnet 2001:db8:100::/64 static-mapping client1 ipv6-address 2001:db8:100::101 + set service dhcpv6-server shared-network-name NET1 subnet 2001:db8:100::/64 static-mapping client1 identifier c5b75e23 + +Commit the changes and show the configuration: + +.. code-block:: sh + + show service dhcp-server shared-network-name NET1 + shared-network-name NET1 { + subnet 2001:db8:100::/64 { + name-server 2001:db8:111::111 + address-range { + start 2001:db8:100::100 { + stop 2001:db8:100::199 { + } + } + static-mapping client1 { + ipv6-address 2001:db8:100::101 + identifier c5b75e23 + } + } + } diff --git a/docs/services/dns-forwarding.rst b/docs/services/dns-forwarding.rst new file mode 100644 index 00000000..a8501c8f --- /dev/null +++ b/docs/services/dns-forwarding.rst @@ -0,0 +1,59 @@ +DNS Forwarding +-------------- + +Use DNS forwarding if you want your router to function as a DNS server for the +local network. There are several options, the easiest being 'forward all +traffic to the system DNS server(s)' (defined with set system name-server): + +.. code-block:: sh + + set service dns forwarding system + +Manually setting DNS servers for forwarding: + +.. code-block:: sh + + set service dns forwarding name-server 8.8.8.8 + set service dns forwarding name-server 8.8.4.4 + +Manually setting DNS servers with IPv6 connectivity: + +.. code-block:: sh + + set service dns forwarding name-server 2001:4860:4860::8888 + set service dns forwarding name-server 2001:4860:4860::8844 + +Setting a forwarding DNS server for a specific domain: + +.. code-block:: sh + + set service dns forwarding domain example.com server 192.0.2.1 + +Example 1 +^^^^^^^^^ + +Router with two interfaces eth0 (WAN link) and eth1 (LAN). A DNS server for the +local domain (example.com) is at 192.0.2.1, other DNS requests are forwarded +to Google's DNS servers. + +.. code-block:: sh + + set service dns forwarding domain example.com server 192.0.2.1 + set service dns forwarding name-server 8.8.8.8 + set service dns forwarding name-server 8.8.4.4 + set service dns forwarding listen-on 'eth1' + +Example 2 +^^^^^^^^^ + +Same as example 1 but with additional IPv6 addresses for Google's public DNS +servers: + +.. code-block:: sh + + set service dns forwarding domain example.com server 192.0.2.1 + set service dns forwarding name-server 8.8.8.8 + set service dns forwarding name-server 8.8.4.4 + set service dns forwarding name-server 2001:4860:4860::8888 + set service dns forwarding name-server 2001:4860:4860::8844 + set service dns forwarding listen-on 'eth1' diff --git a/docs/services/dynamic-dns.rst b/docs/services/dynamic-dns.rst new file mode 100644 index 00000000..67de6471 --- /dev/null +++ b/docs/services/dynamic-dns.rst @@ -0,0 +1,152 @@ +Dynamic DNS +----------- + +VyOS is able to update a remote DNS record when an interface gets a new IP +address. In order to do so, VyOS includes ddclient_, a perl script written for +this exact purpose. + +ddclient_ uses two methods to update a DNS record. The first one will send +updates directly to the DNS daemon, in compliance with RFC2136_. The second +one involves a third party service, like DynDNS.com or any other similar +website. This method uses HTTP requests to transmit the new IP address. You +can configure both in VyOS. + +VyOS CLI and RFC2136 +^^^^^^^^^^^^^^^^^^^^ + +First, create an RFC2136_ config node : + +.. code-block:: sh + + edit service dns dynamic interface eth0 rfc2136 <confignodename> + +Present your RNDC key to ddclient : + +.. code-block:: sh + + set key /config/dyndns/mydnsserver.rndc.key + +Set the DNS server IP/FQDN : + +.. code-block:: sh + + set server dns.mydomain.com + +Set the NS zone to be updated : + +.. code-block:: sh + + set zone mydomain.com + +Set the records to be updated : + +.. code-block:: sh + + set record dyn + set record dyn2 + +You can optionally set a TTL (note : default value is 600 seconds) : + +.. code-block:: sh + + set ttl 600 + +This will generate the following ddclient config blocks: + +.. code-block:: sh + + server=dns.mydomain.com + protocol=nsupdate + password=/config/dyndns/mydnsserver.rndc.key + ttl=600 + zone=mydomain.com + dyn + server=dns.mydomain.com + protocol=nsupdate + password=/config/dyndns/mydnsserver.rndc.key + ttl=600 + zone=mydomain.com + dyn2 + +You can also keep a different dns zone updated. Just create a new config node: + +.. code-block:: sh + + edit service dns dynamic interface eth0 rfc2136 <confignode2> + +VyOS CLI and HTTP dynamic DNS services +^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +VyOS is also able to use any service relying on protocols supported +by ddclient. + +To use such a service, you must define a login, a password, one or multiple +hostnames, a protocol and a server. + +.. code-block:: sh + + edit service dns dynamic interface eth0 service HeNet + set login my-login # set password my-password + set host-name my-tunnel-id + set protocol dyndns2 + set server ipv4.tunnelbroker.net + +VyOS is also shipped with a list of known services. You don't need to set the +protocol and server value as VyOS has defaults provided for those. These are +the services VyOS knows about: + +* afraid +* changeip +* dnspark +* dslreports +* dyndns +* easydns +* namecheap +* noip +* zoneedit + +To use DynDNS for example: + +.. code-block:: sh + + edit service dns dynamic interface eth0 service dyndns + set login my-login + set password my-password + set host-name my-dyndns-hostname + +It's possible to use multiple services : + +.. code-block:: sh + + edit service dns dynamic interface eth0 service dyndns + set login my-login + set password my-password + set host-name my-dyndns-hostname + edit service dns dynamic interface eth0 service HeNet + set login my-login + set password my-password + set host-name my-tunnel-id + set protocol dyndns2 + set server ipv4.tunnelbroker.net + +ddclient behind NAT +^^^^^^^^^^^^^^^^^^^ + +By default, ddclient will update a dynamic dns record using the IP address +directly attached to the interface. If your VyOS instance is behind NAT, your +record will be updated to point to your internal IP. + +ddclient_ has another way to determine the WAN IP address. This is controlled +by these two options: + +.. code-block:: sh + + set service dns dynamic interface eth0 use-web url + set service dns dynamic interface eth0 use-web skip + +ddclient_ will load the webpage at `[url]` and will try to extract an IP +address for the response. ddclient_ will skip any address located before the +string set in `[skip]`. + + +.. include:: references.rst diff --git a/docs/services/index.rst b/docs/services/index.rst new file mode 100644 index 00000000..80405ef7 --- /dev/null +++ b/docs/services/index.rst @@ -0,0 +1,26 @@ +.. _services: + +.. include:: references.rst + +Services +======== + +This chapter descriptes the available system/network services provided by VyOS. + +.. toctree:: + + conntrack + dhcp + dhcpv6 + dhcp-relay + dns-forwarding + dynamic-dns + lldp + mdns-repeater + pppoe-server + udp-broadcast-relay + snmp + ssh + tftp + udp-broadcast-relay + webproxy diff --git a/docs/services/lldp.rst b/docs/services/lldp.rst new file mode 100644 index 00000000..6a3bee7b --- /dev/null +++ b/docs/services/lldp.rst @@ -0,0 +1,97 @@ +LLDP +---- + +The Link Layer Discovery Protocol (LLDP) is a vendor-neutral +link layer protocol in the Internet Protocol Suite used by network devices for +advertising their identity, capabilities, and neighbors on an IEEE 802 local +area network, principally wired Ethernet.[1] The protocol is formally referred +to by the IEEE as Station and Media Access Control Connectivity Discovery +specified in IEEE 802.1AB and IEEE 802.3-2012 section 6 clause 79. + +LLDP performs functions similar to several proprietary protocols, such as +`Cisco Discovery Protocol`_, `Foundry Discovery Protocol`_, +Nortel Discovery Protocol and Link Layer Topology Discovery. + +Information gathered +^^^^^^^^^^^^^^^^^^^^ + +Information gathered with LLDP is stored in the device as a management +information database (MIB_) and can be queried with the Simple Network +Management Protocol (SNMP_) as specified in RFC 2922. The topology of an +LLDP-enabled network can be discovered by crawling the hosts and querying this +database. Information that may be retrieved include: + +* System name and description +* Port name and description +* VLAN name +* IP management address +* System capabilities (switching, routing, etc.) +* MAC/PHY information +* MDI power +* Link aggregation + +Configuration +^^^^^^^^^^^^^ + +* Enable service with: + + :code:`set service lldp` + +Options +******* + +* Configure a Define management-address: + + :code:`set service lldp management-address <x.x.x.x>` + +* Define listening interfaces + + :code:`set service lldp interface <all|interface name>` + +* LLDPd also implements an SNMP subagent. To Enable SNMP queries of the LLDP + database: + + :code:`set service lldp snmp enable` + +* Enable optional/other protocols + + :code:`set service lldp legacy-protocols cdp` + + Supported legacy protocols: + + * ``cdp`` - Listen for CDP for Cisco routers/switches + * ``edp`` - Listen for EDP for Extreme routers/switches + * ``fdp`` - Listen for FDP for Foundry routers/switches + * ``sonmp`` - Listen for SONMP for Nortel routers/switches + + +Display neighbors +^^^^^^^^^^^^^^^^^ + +* Display with: + +``show lldp neighbors`` + +Exemple: + +.. code-block:: sh + + vyos@vyos:~# show lldp neighbors + Capability Codes: R - Router, B - Bridge, W - Wlan r - Repeater, S - Station + D - Docsis, T - Telephone, O - Other + Device ID Local Proto Cap Platform Port ID + --------- ----- ----- --- -------- ------- + swA309 eth0 LLDP ? Cisco IOS Software, GigE0/33 + + +* Options: + + * ``detail`` - Show lldp neighbors detail + * ``interface`` - Show LLDP for specified interface + +Troubleshooting +^^^^^^^^^^^^^^^ + +Use operationnal command ``show log lldp`` to display logs. + +.. include:: references.rst diff --git a/docs/services/mdns-repeater.rst b/docs/services/mdns-repeater.rst new file mode 100644 index 00000000..0afdc90a --- /dev/null +++ b/docs/services/mdns-repeater.rst @@ -0,0 +1,30 @@ +mDNS Repeater +------------- + +Starting with VyOS 1.2 a `Multicast DNS`_ (mDNS) repeater functionality is +provided. + +Multicast DNS uses the 224.0.0.51 address, which is "administratively scoped" +and does not leave the subnet. It re-broadcast mDNS packets from one interface +to other interfaces. This enables support for e.g. Apple Airplay devices across +multiple VLANs. + +To enable mDNS repeater you need to configure at least two interfaces. To re- +broadcast all mDNS packets from `eth0` to `eth1` and vice versa run: + +.. code-block:: sh + + set service mdns repeater interface eth0 + set service mdns repeater interface eth1 + +mDNS repeater can be temporarily disabled without deleting the service using + +.. code-block:: sh + + set service mdns repeater disable + +.. note:: You can not run this in a VRRP setup, if multiple mDNS repeaters + are launched in a subnet you will experience the mDNS packet storm death! + + +.. _`Multicast DNS`: https://en.wikipedia.org/wiki/Multicast_DNS diff --git a/docs/services/pppoe-server.rst b/docs/services/pppoe-server.rst new file mode 100644 index 00000000..1316898e --- /dev/null +++ b/docs/services/pppoe-server.rst @@ -0,0 +1,56 @@ +PPPoE server +------------ + +VyOS utilizes `accel-ppp`_ to provide PPPoE server functionality. It can be +used with local authentication or a connected RADIUS server. + +.. note:: Please be aware, due to an upstream bug, config changes/commits + will restart the ppp daemon and will reset existing PPPoE connections from + connected users, in order to become effective.** + +Configuration +^^^^^^^^^^^^^ + +The example below uses ACN as access-concentrator name, assigns an address +from the pool 10.1.1.100-111, terminates at the local endpoint 10.1.1.1 and +serves requests only on eth1. + +.. code-block:: sh + + set service pppoe-server access-concentrator 'ACN' + set service pppoe-server authentication local-users username foo password 'bar' + set service pppoe-server authentication mode 'local' + set service pppoe-server client-ip-pool start '10.1.1.100' + set service pppoe-server client-ip-pool stop '10.1.1.111' + set service pppoe-server dns-servers server-1 '10.100.100.1' + set service pppoe-server dns-servers server-2 '10.100.200.1' + set service pppoe-server interface 'eth1' + set service pppoe-server local-ip '10.1.1.2' + + +Connections can be locally checked via the command + +.. code-block:: sh + + show pppoe-server sessions + ifname | username | calling-sid | ip | type | comp | state | uptime + -------+----------+-------------------+------------+-------+------+--------+---------- + ppp0 | foo | 08:00:27:fa:3e:50 | 10.1.1.100 | pppoe | | active | 00:04:15 + + +To use a radius server, you need to switch to authentication mode radius and +of course need to specify an IP for the server. You can have multiple RADIUS +server configured, if you wish to achieve redundancy. + +.. code-block:: sh + + set service pppoe-server access-concentrator 'ACN' + set service pppoe-server authentication mode 'radius' + set service pppoe-server authentication radius-server 10.1.100.1 secret 'secret' + set service pppoe-server interface 'eth1' + set service pppoe-server local-ip '10.1.1.2' + +RADIUS provides the IP addresses in the example above via Framed-IP-Address. + + +.. _`accel-ppp`: https://accel-ppp.org/ diff --git a/docs/services/references.rst b/docs/services/references.rst new file mode 100644 index 00000000..6e6e9595 --- /dev/null +++ b/docs/services/references.rst @@ -0,0 +1,13 @@ +.. _`Cisco Discovery Protocol`: https://en.wikipedia.org/wiki/Cisco_Discovery_Protocol +.. _ddclient: http://sourceforge.net/p/ddclient/wiki/Home/ +.. _`Foundry Discovery Protocol`: https://en.wikipedia.org/wiki/Foundry_Discovery_Protocol +.. _MIB: https://en.wikipedia.org/wiki/Management_information_base +.. _RFC2136: https://www.ietf.org/rfc/rfc2136.txt +.. _SNMP: https://en.wikipedia.org/wiki/Simple_Network_Management_Protocol +.. _SNMPv2: https://en.wikipedia.org/wiki/Simple_Network_Management_Protocol#Version_2 +.. _SNMPv3: https://en.wikipedia.org/wiki/Simple_Network_Management_Protocol#Version_3 +.. _SSH: https://en.wikipedia.org/wiki/Secure_Shell +.. _Squid3: http://www.squid-cache.org/ +.. _Squidguard: http://www.squidguard.org/ +.. _TFTP: https://en.wikipedia.org/wiki/Trivial_File_Transfer_Protocol + diff --git a/docs/services/snmp.rst b/docs/services/snmp.rst new file mode 100644 index 00000000..e11e3969 --- /dev/null +++ b/docs/services/snmp.rst @@ -0,0 +1,180 @@ +SNMP +---- + +Simple Network Management Protocol (SNMP_) is an Internet Standard protocol +for collecting and organizing information about managed devices on IP networks +and for modifying that information to change device behavior. Devices that +typically support SNMP include cable modems, routers, switches, servers, +workstations, printers, and more. + +SNMP is widely used in network management for network monitoring. SNMP exposes +management data in the form of variables on the managed systems organized in +a management information base (MIB_) which describe the system status and +configuration. These variables can then be remotely queried (and, in some +circumstances, manipulated) by managing applications. + +Three significant versions of SNMP have been developed and deployed. SNMPv1 is +the original version of the protocol. More recent versions, SNMPv2c and SNMPv3, +feature improvements in performance, flexibility and security. + +SNMP is a component of the Internet Protocol Suite as defined by the Internet +Engineering Task Force (IETF). It consists of a set of standards for network +management, including an application layer protocol, a database schema, and a +set of data objects. + +Overview and basic concepts +^^^^^^^^^^^^^^^^^^^^^^^^^^^ + +In typical uses of SNMP, one or more administrative computers called managers +have the task of monitoring or managing a group of hosts or devices on a +computer network. Each managed system executes a software component called an +agent which reports information via SNMP to the manager. + +An SNMP-managed network consists of three key components: + +* Managed devices + +* Agent – software which runs on managed devices + +* Network management station (NMS) – software which runs on the manager + +A managed device is a network node that implements an SNMP interface that +allows unidirectional (read-only) or bidirectional (read and write) access to +node-specific information. Managed devices exchange node-specific information +with the NMSs. Sometimes called network elements, the managed devices can be +any type of device, including, but not limited to, routers, access servers, +switches, cable modems, bridges, hubs, IP telephones, IP video cameras, +computer hosts, and printers. + +An agent is a network-management software module that resides on a managed +device. An agent has local knowledge of management information and translates +that information to or from an SNMP-specific form. + +A network management station executes applications that monitor and control +managed devices. NMSs provide the bulk of the processing and memory resources +required for network management. One or more NMSs may exist on any managed +network. + +.. figure:: /_static/images/service_snmp_communication_principles_diagram.png + :scale: 20 % + :alt: Principle of SNMP Communication + + Image thankfully borrowed from + https://en.wikipedia.org/wiki/File:SNMP_communication_principles_diagram.PNG + which is under the GNU Free Documentation License + +.. note:: VyOS SNMP supports both IPv4 and IPv6. + +SNMP protocol versions +^^^^^^^^^^^^^^^^^^^^^^ + +VyOS itself supports SNMPv2_ (version 2) and SNMPv3_ (version 3) where the +later is recommended because of improved security (optional authentication and +encryption). + +SNMPv2 +^^^^^^ + +SNMPv2 is the original and most commonly used version. For authorizing clients, +SNMP uses the concept of communities. Communities may have authorization set +to read only (this is most common) or to read and write (this option is not +actively used in VyOS). + +SNMP can work synchronously or asynchronously. In synchronous communication, +the monitoring system queries the router periodically. In asynchronous, the +router sends notification to the "trap" (the monitoring host). + +SNMPv2 does not support any authentication mechanisms, other than client source +address, so you should specify addresses of clients allowed to monitor the +router. Note that SNMPv2 also supports no encryption and always sends data in +plain text. + +Example +******* + +.. code-block:: sh + + # Define a community + set service snmp community routers authorization ro + + # Allow monitoring access from the entire network + set service snmp community routers network 192.0.2.0/24 + set service snmp community routers network 2001::db8:ffff:eeee::/64 + + # Allow monitoring access from specific addresses + set service snmp community routers client 203.0.113.10 + set service snmp community routers client 203.0.113.20 + + # Define optional router information + set service snmp location "UK, London" + set service snmp contact "admin@example.com" + + # Trap target if you want asynchronous communication + set service snmp trap-target 203.0.113.10 + + # Listen only on specific IP addresses (port defaults to 161) + set service snmp listen-address 172.16.254.36 port 161 + set service snmp listen-address 2001:db8::f00::1 + + +SNMPv3 +^^^^^^ + +SNMPv3 is an updated version that, among other things, supports encryption and +cryptographic authentication of clients. + +Example +******* + +.. code-block:: sh + + set service snmp v3 engineid '0x0aa0d6c6f450' + set service snmp v3 group defaultgroup mode 'ro' + set service snmp v3 group defaultgroup seclevel 'priv' + set service snmp v3 group defaultgroup view 'defaultview' + set service snmp v3 view defaultview oid '1' + + set service snmp v3 user testUser1 auth plaintext-key testUserKey1 + set service snmp v3 user testUser1 auth type 'md5' + set service snmp v3 user testUser1 engineid '0x0aa0d6c6f450' + set service snmp v3 user testUser1 group 'defaultgroup' + set service snmp v3 user testUser1 mode 'ro' + set service snmp v3 user testUser1 privacy type aes + set service snmp v3 user testUser1 privacy plaintext-key testUserKey1 + +After commit the resulting configuration will look like: + +.. note:: SNMPv3 keys won't we stored in plaintext. On ``commit`` the keys + will be encrypted and the encrypted key is based on the engineid! + +.. code-block:: sh + + vyos@vyos# show service snmp + v3 { + engineid 0x0aa0d6c6f450 + group defaultgroup { + mode ro + seclevel priv + view defaultview + } + user testUser1 { + auth { + encrypted-key 0x3b68d4162c2c817b8e9dfb6f08583e5d + type md5 + } + engineid 0x0aa0d6c6f450 + group defaultgroup + mode ro + privacy { + encrypted-key 0x3b68d4162c2c817b8e9dfb6f08583e5d + type aes + } + } + view defaultview { + oid 1 { + } + } + } + + +.. include:: references.rst diff --git a/docs/services/ssh.rst b/docs/services/ssh.rst new file mode 100644 index 00000000..4d96f8de --- /dev/null +++ b/docs/services/ssh.rst @@ -0,0 +1,150 @@ +SSH +--- + +Secure Shell (SSH_) is a cryptographic network protocol for operating network +services securely over an unsecured network.[1] The standard TCP port for SSH +is 22. The best known example application is for remote login to computer +systems by users. + +SSH provides a secure channel over an unsecured network in a client-server +architecture, connecting an SSH client application with an SSH server. Common +applications include remote command-line login and remote command execution, +but any network service can be secured with SSH. The protocol specification +distinguishes between two major versions, referred to as SSH-1 and SSH-2. + +The most visible application of the protocol is for access to shell accounts +on Unix-like operating systems, but it sees some limited use on Windows as +well. In 2015, Microsoft announced that they would include native support for +SSH in a future release. + +SSH was designed as a replacement for Telnet and for unsecured remote shell +protocols such as the Berkeley rlogin, rsh, and rexec protocols. +Those protocols send information, notably passwords, in plaintext, +rendering them susceptible to interception and disclosure using packet +analysis. The encryption used by SSH is intended to provide confidentiality +and integrity of data over an unsecured network, such as the Internet. + +Configuration +^^^^^^^^^^^^^ + +Enabling SSH only requires you to add ``service ssh port NN``, where 'NN' is +the port you want SSH to listen on. By default, SSH runs on port 22. + +.. code-block:: sh + + set service ssh port 22 + +Options +******* + +* Listening address - Specify the IPv4/IPv6 listening address for connection + requests. Multiple ``listen-address`` nodes can be defined. + + :code:`set service ssh listen-address <address>` + +* Allow ``root`` login, this can be set to allow ``root`` logins on SSH + connections, however it is not advisable to use this setting as this bears + serious security risks. The default system user posesses all required + privileges. + + :code:`set service ssh allow-root` + +* Allowed ciphers - A number of allowed ciphers can be specified, use multiple + occurances to allow multiple ciphers. + + :code:`set service ssh ciphers <cipher>` + + Available ciphers: + + * `3des-cbc` + * `aes128-cbc` + * `aes192-cbc` + * `aes256-cbc` + * `aes128-ctr` + * `aes192-ctr` + * `aes256-ctr` + * `arcfour128` + * `arcfour256` + * `arcfour` + * `blowfish-cbc` + * `cast128-cbc` + +* Disable password authentication - If SSH key authentication is set up, + password-based user authetication can be disabled. This hardens security! + + :code:`set service ssh disable-password-authentication` + +* Disable host validation - Disable the host validation through reverse DNS + lookups. + + :code:`set service ssh disable-host-validation` + +* MAC algorithms - Specifies the available MAC (message authentication code) + algorithms. The MAC algorithm is used in protocol version 2 for data + integrity protection. Multiple algorithms can be entered. + + :code:`set service ssh macs <macs>` + + Supported MACs: + + * `hmac-md5` + * `hmac-md5-96` + * `hmac-ripemd160` + * `hmac-sha1` + * `hmac-sha1-96` + * `hmac-sha2-256` + * `hmac-sha2-512` + * `umac-64@openssh.com` + * `umac-128@openssh.com` + * `hmac-md5-etm@openssh.com` + * `hmac-md5-96-etm@openssh.com` + * `hmac-ripemd160-etm@openssh.com` + * `hmac-sha1-etm@openssh.com` + * `hmac-sha1-96-etm@openssh.com` + * `hmac-sha2-256-etm@openssh.com` + * `hmac-sha2-512-etm@openssh.com` + * `umac-64-etm@openssh.com` + * `umac-128-etm@openssh.com` + + +Key Authentication +################## + +It is highly recommended to use SSH Key authentication. By default there is +only one user (``vyos``), and you can assign any number of keys to that user. +You can generate a ssh key with the ``ssh-keygen`` command on your local +machine, which will (by default) save it as ``~/.ssh/id_rsa.pub`` which is in +three parts: + + ``ssh-rsa AAAAB3NzaC1yc2EAAAADAQABAA...VByBD5lKwEWB username@host.example.com`` + +Only the type (``ssh-rsa``) and the key (``AAAB3N...``) are used. Note that +the key will usually be several hundred characters long, and you will need to +copy and paste it. Some terminal emulators may accidentally split this over +several lines. Be attentive when you paste it that it only pastes as a single +line. The third part is simply an identifier, and is for your own reference. + + +**Assign SSH Key to user** + +Under the user (in this example, ``vyos``), add the public key and the type. +The `identifier` is simply a string that is relevant to you. + +.. code-block:: sh + + set system login user vyos authentication public-keys 'identifier' key "AAAAB3Nz...." + set system login user vyos authentication public-keys 'identifier' type ssh-rsa" + +You can assign multiple keys to the same user by changing the identifier. In +the following example, both Unicron and xrobau will be able to SSH into VyOS +as the ``vyos`` user using their own keys. + +.. code-block:: sh + + set system login user vyos authentication public-keys 'Unicron' key "AAAAB3Nz...." + set system login user vyos authentication public-keys 'Unicron' type ssh-rsa + set system login user vyos authentication public-keys 'xrobau' key "AAAAQ39x...." + set system login user vyos authentication public-keys 'xrobau' type ssh-rsa + + + diff --git a/docs/services/tftp.rst b/docs/services/tftp.rst new file mode 100644 index 00000000..96b33a65 --- /dev/null +++ b/docs/services/tftp.rst @@ -0,0 +1,42 @@ +TFTP +---- + +Trivial File Transfer Protocol (TFTP_) is a simple lockstep File Transfer +Protocol which allows a client to get a file from or put a file onto a remote +host. One of its primary uses is in the early stages of nodes booting from a +local area network. TFTP has been used for this application because it is very +simple to implement. + +Example +^^^^^^^ + +.. code-block:: sh + + # If you want to enable uploads, else TFTP server will act as read-only (optional) + set service tftp-server allow-upload + + # Directory for TFTP server content + set service tftp-server directory '/config/tftpboot' + + # On which addresses we want to listen for incoming TFTP connections? (mandatory) + set service tftp-server listen-address '2001:db8:ffee::1' + set service tftp-server listen-address '10.10.1.1' + +.. note:: Choose your ``directory`` location carefully or you will loose the + content on image upgrades. Any directory under ``/config`` is save at this + will be migrated. + +.. note:: Configuring a listen-address is essential for the service to work. + +The resulting configuration will look like: + +.. code-block:: sh + + vyos@vyos# show service + tftp-server { + allow-upload + directory /config/tftpboot + listen-address 2001:db8:ffee::1 + listen-address 10.10.1.1 + } + diff --git a/docs/services/udp-broadcast-relay.rst b/docs/services/udp-broadcast-relay.rst new file mode 100644 index 00000000..9ea53826 --- /dev/null +++ b/docs/services/udp-broadcast-relay.rst @@ -0,0 +1,53 @@ +UDP broadcast relay +------------------- + +Certain vendors use broadcasts to identify their equipemnt within one ethernet +segment. Unfortunately if you split your network with multiple VLANs you loose +the ability of identifying your equiment. + +This is where "UDP broadcast relay" comes into play! It will forward received +broadcasts to other configured networks. + +Every UDP port which will be forward requires one unique ID. Currently we +support 99 IDs! + +Example #1: To forward all broadcast packets received on `UDP port 1900` on +`eth3`, `eth4` or `eth5` to all other interfaces in this configuration. + +.. code-block:: sh + + set service broadcast-relay id 1 description 'SONOS' + set service broadcast-relay id 1 interface 'eth3' + set service broadcast-relay id 1 interface 'eth4' + set service broadcast-relay id 1 interface 'eth5' + set service broadcast-relay id 1 port '1900' + +Example #2: To Forward all broadcasts packets received on `UDP port 6969` on +`eth3` or `eth4` to the other interface in this configuration. + +.. code-block:: sh + + set service broadcast-relay id 2 description 'SONOS MGMT' + set service broadcast-relay id 2 interface 'eth3' + set service broadcast-relay id 2 interface 'eth4' + set service broadcast-relay id 2 port '6969' + +Disable Instance(s) +^^^^^^^^^^^^^^^^^^^ + +Each broadcast relay instance can be individually disabled without deleting the +configured node by using the following command: + +.. code-block:: sh + + set service broadcast-relay id <n> disable + +In addition you can also disable the whole service without removing the +configuration by: + +.. code-block:: sh + + set service broadcast-relay disable + +.. note:: You can run the UDP broadcast relay service on multiple routers + connected to a subnet. There is **NO** UDP broadcast relay packet storm! diff --git a/docs/services/webproxy.rst b/docs/services/webproxy.rst new file mode 100644 index 00000000..d1c2ca2e --- /dev/null +++ b/docs/services/webproxy.rst @@ -0,0 +1,121 @@ +Webproxy +-------- + +The proxy service in VyOS is based on Squid3 and some related modules. + +Squid is a caching and forwarding HTTP web proxy. It has a wide variety of +uses, including speeding up a web server by caching repeated requests, +caching web, DNS and other computer network lookups for a group of people +sharing network resources, and aiding security by filtering traffic. Although +primarily used for HTTP and FTP, Squid includes limited support for several +other protocols including Internet Gopher, SSL,[6] TLS and HTTPS. Squid does +not support the SOCKS protocol. + +All examples here assumes that your inside ip address is ``192.168.0.1``. +Replace with your own where applicable. + +URL Filtering is provided by Squidguard_. + +Configuration +^^^^^^^^^^^^^^ + +.. code-block:: sh + + # Enable proxy service + set service webproxy listen-address 192.168.0.1 + + # By default it will listen to port 3128. If you wan't something else you have to define that. + set service webproxy listen-address 192.168.0.1 port 2050 + + # By default the transparent proxy on that interface is enabled. To disable that you simply + set service webproxy listen-address 192.168.0.1 disable-transparent + + # Block specific urls + set service webproxy url-filtering squidguard local-block myspace.com + + # If you want to you can log these blocks + set service webproxy url-filtering squidguard log local-block + + +Options +******* + +Filtering by category +^^^^^^^^^^^^^^^^^^^^^ + +If you wan't to use existing blacklists you have to create/download a database +first. Otherwise you will not be able to commit the config changes. + +.. code-block:: sh + + vyos@vyos# commit + [ service webproxy ] + Warning: no blacklists installed + Unknown block-category [ads] for policy [default] + + [[service webproxy]] failed + Commit failed + +* Download/Update complete blacklist + + :code:`update webproxy blacklists` + +* Download/Update partial blacklist + + :code:`update webproxy blacklists category ads` + + Use tab completion to get a list of categories. + +* To auto update the blacklist files + + :code:`set service webproxy url-filtering squidguard auto-update update-hour 23` + +* To configure blocking add the following to the configuration + + :code:`set service webproxy url-filtering squidguard block-category ads` + + :code:`set service webproxy url-filtering squidguard block-category malware` + +Authentication +^^^^^^^^^^^^^^ + +TBD: https://wiki.vyos.net/wiki/Web_proxy_LDAP_authentication + +Adjusting cache size +^^^^^^^^^^^^^^^^^^^^ + +The size of the proxy cache can be adjusted by the user. + +.. code-block:: sh + + set service webproxy cache-size + Possible completions: + <0-4294967295> + Disk cache size in MB (default 100) + 0 Disable disk caching + 100 + +Bypassing the webproxy +^^^^^^^^^^^^^^^^^^^^^^ + +Some services don't work correctly when being handled via a web proxy. +So sometimes it is useful to bypass a transparent proxy: + +* To bypass the proxy for every request that is directed to a specific + destination: + + :code:`set service webproxy whitelist destination-address 1.2.3.4` + + :code:`set service webproxy whitelist destination-address 4.5.6.0/24` + + +* To bypass the proxy for every request that is coming from a specific source: + + :code:`set service webproxy whitelist source-address 192.168.1.2` + + :code:`set service webproxy whitelist source-address 192.168.2.0/24` + + (This can be useful when a called service has many and/or often changing + destination addresses - e.g. Netflix.) + +.. include:: references.rst |